Belson Outdoors PTST6 User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # PTST6 Instructions Sheet
www.belson.com
RECYCLED PLASTIC STEP THROUGH PICNIC TABLES

www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
A - TABLE TOP
( 1 ) - ONE TABLE TOP
D - SEAT
( 2 ) TWO SEATS
E - UNDER SEAT SUPPORT
( 2 ) - TWO UNDER SEAT SUPPORTS
B - RIGHT LEG
( 2 ) TWO RIGHT LEGS
F - ANGLE SUPPORT
( 2 ) - TWO ANGLE SUPPORTS
I - CENTER SUPPORT
( 1 ) - ONE CENTER SUPPORT
H - LEG CROSS BLOCK
( 2 ) TWO LEG CROSS BLOCKS
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK
C - LEFT LEG
( 2 ) - TWO LEFT LEGS
G - SEAT SUPPORT
( 4 ) - FOUR SEAT SUPPORTS

www.belson.com
10 - 3/8” X 5“ HEX HEAD BOLT
18 - 3/8” X 4“ HEX HEAD LAG BOLT
2 - 3/8” X 2-1/2” HEX HEAD LAG BOLT 8 - 3/8” NYLON LOCK NUT
38 - 3/8” FLAT WASHER 2 - 5/8” X 1” CROSS DOWEL
18 - #12 X 3” FLAT HEAD PHILLIPS SCREW
ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
1 - #3 PHILLIPS DRIVE BIT 2 - 9/16” SOCKET WRENCH
1 - 1/4” FLAT HEAD SCREWDRIVER
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.

www.belson.com
STEP #1:
WHILE LEGS ARE PLACED IN THE CONFIGURATION AS SHOWN ABOVE PLACE A LEG CROSS BLOCK
BETWEEN THE TWO LEGS AND ALIGN THE HOLES, INSERT ( 1 ) - ONE 3/8” X 4” HEX HEAD LAG BOLT
WITH ( 1 ) - ONE 3/8” FLAT WASHER PER HOLE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
LEG CROSS BLOCK
3/8” FLAT WASHER
3/8” X 4” HEX HEAD LAG BOLT

3/8” FLAT WASHER
3/8” NYLON LOCK NUT
3/8” X 5” HEX HEAD BOLT
3/8” FLAT WASHER
www.belson.com
STEP #2:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE LEGS TO THE UNDER TOP SUPPORTS BEING SURE
THAT THE COUNTER BORES ARE POINTING TOWARD THE CENTER OF THE TABLE AS SHOWN ABOVE.
USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) 3/8” NYLON LOCK
NUT AND ( 1 ) ONE 3/8” FLAT WASHER PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

NOTE: LEG HAS BEEN REMOVED FOR CLARITY.
PLEASE DO NOT REMOVE LEG.
3/8” X 4” LAG BOLT
3/8” FLAT WASHER
3/8” FLAT WASHER
3/8” X 2-1/2” LAG BOLT
www.belson.com
STEP #3:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE CROSS SUPPORTS TO THE LEGS. USE ( 1 ) ONE
3/8” X 4” HEX HEAD LAG BOLT ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER PER HOLE TO SECURE. FASTEN
THE CROSS SUPPORTS TO THE TABLE TOP. USE ( 1 ) ONE 3/8” X 2 - 1/2” HEX HEAD BOLT ALONG WITH
( 1 ) ONE 3/8” FLAT WASHER PER HOLE TO SECURE.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

www.belson.com
STEP #4:
WHILE TABLE IS UP-SIDE-DOWN SLIDE THE CROSS DOWEL INTO THE CROSS SUPPORT BOARD ON BOTH
ENDS. THEN ALIGN THE HOLES WITH THE HOLES ON THE LEG CROSS BLOCKS. SLIDE A 3/8” X 5” HEX HEAD
BOLT INTO THE FRONT SIDE OF THE LEG CROSS BLOCK AND THREAD IT INTO THE CROSS DOWEL IN THE
CROSS SUPPORT BOARD.
NOTE: DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
CROSS DOWEL
MAKE SURE YOU ALIGN THE HOLE
IN THE CROSS DOWEL WITH THE
TAP BOLT HOLE THEN THREAD THE
4” HEX HEAD TAP BOLT
TOGETHER.
3/8” FLAT WASHER
3/8” X 5” HEX HEAD BOLT

3/8” X 5” HEX HEAD LAG BOLT
3/8” FLAT WASHER
NOTE: BE SURE TO TIGHTEN AL L THE LOOSE BOLTS AFTER THIS STEP IS COMPLETE.
STEP #5:
WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE UNDER SEAT SUPPORTS TO THE SEAT CROSS
SUPPORTS. USE ( 1 ) ONE 3/8” X 5” HEX HEAD LAG BOLT AND ( 1 ) ONE 3/8” FLAT WASHER PER
HOLE TO SECURE.
www.belson.com

STEP #6:
FLIP THE TABLE UPRIGHT ONTO THE LEGS. PLEASE TAKE CAUTION WHILE FLIPPING THE
TABLE. AT THIS POINT IN THE ASSEMBLY THE TABLE WEIGHS APPROXIMATELY 260 POUNDS.
STEP #7:
WHILE TABLE IS IN THE UP RIGHT POSITION ALIGN THE HOLES ON THE SEAT SUPPORTS WITH THE
PRE DRILLED HOLES IN THE LEG AND SCREW A #12 X 3” PHILLIPS HEAD SCREW TIGHT.
www.belson.com
#12 X 3” FLAT HEAD PHILLIPS SCREW

#12 X 3” FLAT HEAD PHILLIPS SCREW
STEP #8:
WHILE THE TABLE IS UPRIGHT FASTEN THE SEATS TO THE SEAT CROSS SUPPORTS AND UNDER SEAT
SUPPORTS BEING SURE TO CENTER ALL HOLES OVER BOARDS. USE ( 1 ) ONE #12 X 3” FLAT HEAD
PHILLIPS SCREW PER HOLE TO SECURE.
www.belson.com