Belson Outdoors Park King User manual

(4) PARK KING
“J” LEG
700204
(2) TOP “L” BRACKET
700023
(1) CENTER
CHANNEL
700063
(1) CENTER BRACKET
700043
www.belson.comWeb Site:North Aurora, IL 60542-0207 1-630-897-0573Fax:P.O. Box 207 1-630-897-8489Phone:111 North River Road 1-800-323-5664Toll Free:Principal Plant and General Offices
(2) SUPPORT BRACE
700081 (1) HARDWARE BAG
702304
PARK KING
PK-WF FRAME KIT CONTENTS:
Thank you for buying a BELSON OUTDOORS quality product.
Please read and follow assembly instructions. Refer to appropriate page depending on the table you
wish to put together. If the lumber is not provided by Belson, follow drilling instructions on page (2).
LUMBER CONTENTS AND WOOD DRILLING INST.2)
WOOD TABLE 6’ ASSEMBLY INSTRUCTIONS3)FRAME KIT CONTENTS1)
INDEX
OUTER HOLES
MID RANGE
HOLES
CENTER HOLE
TOP HOLE
1
700304

WOOD PICNIC TABLE DRILL PATTERN
RECOMMENDED LUMBER: 2” x 10” Nominal (1-1/2” thick by 9-1/4” wide).
1.-Make sure all 5 boards are of consistent length, roughly 6’.
2.-Lay all 5 boards on a flat surface that will not damage the wood with the best side down.
3.-Draw centered Vertical and Horizontal Lines, then two Lateral Lines 29-1/2” from Vertical
Center Line on all boards (this will be your reference for hole locations).
4.-Drill 3/8” diameter holes in boards per drill pattern and notes indicated above.
5.-If desired, cut miters as per top of page lumber kit details and paint or seal before assembly.
6’
59”
VERTICAL CENTER LINE
29-1/2” 29-1/2”
DRILL
DRILL
HORIZONTAL
DRILL
DRILL
CENTER LINE
DRILL
DRILL CENTER HOLE
ON 3 TOP BOARDS ONLY
LAT. LINE
LAT. LINE
2-1/2”
2-1/2” 2-1/2”
2-1/2”
TOOLS NEEDED: drill, 3/8” drill bit, pencil and tape measure or ruler.
BELSON PRE CUT & PRE DRILLED LUMBER KIT (OPTIONAL)
LUMBER KIT CONTENTS:
CENTER (1) NO MITERED CORNERS, 5 HOLES
SIDE (2) 2 MITERED CORNERS, 5 HOLES
SEAT (2) 4 MITERED CORNERS, 4 HOLES
NATURAL REDWOOD ACQ
S.Y.PINE STAINED TREATED
CENTER 6' 700111 700112 700113
SIDE 6' 700131 700132 700133
SEAT 6' 700151 700152 700153
2
700304

6’
W
OOD PARK KING
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED: 9/16” wrench and hammer.
6.- Place brace
between 2 table “J”
Legs and insert 3-1/2”
long bolt.
Hand fasten nut.
7.- Attach Leg set to
inside Top “L” Bracket.
Use 2” bolts / nuts.
8.- Attach loose end of Brace
to Center Bracket mid range
holes using 1” bolts / nuts.
Note: Do not fully tighten
any of the nuts from steps
6-8 until step 11 below.
9.- Flip the partial table assembly into
an upright position.
10.- Attach Seats to Frame using 3-1/2”
carriage bolts / nuts as shown.
SIDE
SIDE
CENTER
SEAT
SEAT
3
700304
1.- Insert 2-1/4” carriage bolts through 3 Top Boards best face and lay (Side with 2 miters facing out - Center no miters - Side
with 2 miters facing out ) on a non-abrasive flat surface that will not damage the lumber with the best side facing down.
2.- Align Top Boards and space them about 1/8” apart.
3.- Place 2 Top “L” Brackets as shown and hand tighten nuts in place.
4.- Place the Center Channel with the legs up as shown and hand tighten the 2 outer nuts. Attach
Center Bracket’s center hole to the center bolt and hand tighten nut.
5.- Make sure Top Boards are aligned and spaced. Then tighten all 15 nuts.
11.- Tighten all nuts firmly, including assembled parts in
steps 6, 7 and 8.
12.- The Picnic Table is finished.