Belson Outdoors HB96A User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # HB96A Instructions Sheet
www.belson.com
MONARQUE BENCH WITH ARMRESTS

BENCH END
( 4 ) - FOUR BENCH ENDS
D - BENCH BOARD W/ ARM HOLE
( 3 ) - BENCH BOARDS W/ ARM HOLES
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
( 4 ) FOUR BENCH BOARDS
FP - FASTENER PACK
( 1 ) - ONE FASTENER PACK
C - ARM
( 2 ) - TWO ARMS

www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED.
6 - 3/8” X 2 1/2” HEX HEAD LAG BOLT
6 - 3/8” FLAT WASHER
56 - #12 X 2” PAN HEAD PHILLIPS SCREW
ALSO NEED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS:
1 - 9/16” SOCKET WRENCH
1 - #3 PHILLIPS DRIVE BIT

www.belson.com
STEP #1:
STAND ( 1 ) ONE BENCH END UPRIGHT AND PLACE ( 1 ) ONE BENCH BOARD ( A ) ON POSITION 1 BEING
SURE TO ALIGN THE PILOT HOLES TO THE PRE-DRILLED HOLES IN THE BENCH END. AFTER THE HOLES
ARE PROPERLY ALIGNED, FASTEN WITH ( 1 ) ONE #12 X 2” PAN HEAD PHILLIPS SCREW IN THE
PRE-DRILLED HOLE ON THE RIGHT SID OF THE BENCH END.
DO NOT TIGHTEN BOLTS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.
FIG # 1:
IN ORDER TO MAKE THE ASSEMBLY OF THIS MONARQUE BENCH WITH ARMS EASIER WHILE
GOING THROUGH THE ASSEMBLY PROCESS THE BOARD POSITIONS ARE NUMBERED AND
WILL BE REFERENCED IN LATER STEPS.
NOTE: STAND BENCH ENDS FLAT ON GROUND. VIEW IS ONLY TO SHOW DETAIL.
#12 X 2” PAN HEAD
PHILLIPS SCREW

#12 X 2” PAN HEAD
PHILLIPS SCREW
www.belson.com
STEP #2:
STAND THE OTHER ( 3 ) THREE BENCH ENDS UPRIGHT, ONE AT A TIME, AND PLACE THE BENCH BOARD
ALREADY ATTACHED TO THE FIRST BENCH END, ON POSITION 1 BEING SURE TO ALIGN THE PILOT
HOLES WITH THE PRE-DRILLED HOLES IN THE BENCH END. AFTER THE HOLES ARE PROPERLY ALIGNED,
FASTEN WITH ( 1 ) ONE #12 X 2” PAN HEAD PHILLIPS SCREW IN THE PRE-DRILLED HOLE ON THE RIGHT
SIDE OF THE BENCH END.
DO NOT TIGHTEN SCREWS COMPLETELY. THIS WILL BE DONE IN A LATER STEP.

#12 X 2” PAN HEAD
PHILLIPS SCREW
www.belson.com
STEP #4:
PLACE A SECOND BENCH BOARD ( A ) ON POSITION 7. REPEAT STEPS 1 - 3 TO ATTACH. USE ( 1 )
ONE #12 X 2” PAN HEAD PHILLIPS SCREW PER HOLE TO FASTEN.
STEP #3:
ALIGN THE PILOT HOLES ON THE BENCH BOARD TO THE PRE-DRILLED HOLES ON THE LEFT SIDE
OF THE BENCH ENDS. AFTER THE HOLES ARE PROPERLY ALIGNED, FASTEN WITH ( 1 ) ONE #12 X 2”
PAN HEAD PHILLIPS SCREW PER BENCH END.
NOTE: BE SURE TO TIGHTEN SCREWS COMPLETELY AFTER THIS STEP.

www.belson.com
STEP #5:
REPEAT STEPS 1 - 3 TO ATTACH BENCH BOARDS WITH ARM HOLES ( B ) ON POSITIONS 2 & 5.
USE ( 1 ) ONE #12 X 2” PAN HEAD PHILLIPS SCREW PER HOLE TO FASTEN.
#12 X 2” PAN HEAD
PHILLIPS SCREW

www.belson.com
STEP #6:
REPEAT STEPS 1 - 3 TO ATTACH BENCH BOARDS WITH ARM HOLES ( B ) ON POSITIONS 3, 4 & 6.
USE ( 1 ) ONE #12 X 2” PAN HEAD PHILLIPS SCREW PER HOLE TO FASTEN.
#12 X 2” PAN HEAD
PHILLIPS SCREW

www.belson.com
STEP #7:
PLACE THE ARMS ON THE BENCH BOARDS FASTENED TO POSITIONS 3, 4 & 6. ALIGN THE
PRE-DRILLED HOLES ON THE BENCH BOARDS WITH THE PILOT HOLES IN THE ARMS. AFTER THE
HOLES ARE PROPERLY ALIGNED, FASTEN WITH ( 3 ) THREE 3/8” FLAT WASHERS ALONG WIH ( 3 )
THREE 3/8” X 2 1/2” HEX HEAD LAG BOLTS.
3/8” FLAT
WASHER
3/8” X 2 1/2”
HEX HEAD
LAG BOLT