Bennett Pacific eNVy 1000 Series User manual

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456
USA 800-235-7618 ~ Outside USA 231-798-1310
[e-mail] ~ www.bennettpump.com
Bennett Pacific eNVy Series
1000 Series Remote Dispensers (Spec. 100 & Spec. 200)
Installation Manual
127542 Rev N 3/13/19
Only Trained Personnel May Work on This Equipment
READ THIS MANUAL
This manual has important information for safe installation and operation of this equipment. Read and understand
this manual before applying power. Keep this manual and tell all service personnel to read this manual. If you do not
follow the instructions, you can cause bodily injury, death, or damage to the equipment.

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456
USA 800-235-7618 ~ Outside USA 231-798-1310
[e-mail] ~ www.bennettpump.com
The material included in this installation manual is accurate at the date of publication. The intent of this manual is to
assist. If further assistance is required, please contact the Bennett Technical Service Department at 1-800-423-6638.
Bennett Marketing Services can be contacted by mail, facsimile, telephone or e-mail at the locations specified below:
Bennett Pump Company
1218 East Pontaluna Road
Spring Lake, MI 49456
Telephone from USA 1-800-235-7618
Telephone from outside USA 231-798-1310, Extension 287, or 269
Facsimile: 231-799-6200
Email: [email protected] or [e-mail]
Website: www.bennettpump.com
For new manuals, visit our web page at http://www.bennettpump.com
IMPORTANT
Examine the shipment immediately upon arrival to make certain there has been no damage or loss in transit.
Bennett Pump Company, as shipper, is not liable for the hazards of transportation. Please make damage
claims directly to the truck line.
NOTICE: This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interface, and (2) this device must accept interference
received, including interference that may cause undesired operation.
Not all equipment covered in this manual is listed by Underwriters Laboratories.
REV LEVEL
DATE
DESCRIPTION
A
B
8/21/16
C
4/26/16
D
6/22/16
Add Wire Clips and Fasteners to Wiring Section per UL
E
8/15/16
Add 819 Metal Cover Removal Instructions per UL.
Update Product Supply Lines for Model Number 1X44M2
Update Pacific Extended Blender Installation Diagram –Footprint to Rev B
F
9/14/16
Update dispenser image.
Update DIN 1K 1000 Series Pacific to Rev J
G
12/2/16
Add Health, Security, Safety, Environment (HSSE) disclaimer to Safety Instructions.
Update DIN Sheet
H
1/17/17
Add Bennett International Limited Warranty for Dispensers and Pumps
Update P4525 Configuration Drawings Pacific Extended Blender
Update Pacific Extended Blender Installation Diagram –Footprint to Rev C
Add Generic Current Loop Wiring Diagram
J
4/17/17
Update Footprint 129212-P1247 to Rev H
K
5/2/17
Add 919 Upper CPU TS1
Update all Wiring Diagrams to Revision D.
L
1/23/18
Update Warranties
Add Spec. 200 DIN
Update Standard Footprint to Rev J & Extended Blender Footprint to Rev D
Update Wiring Diagrams to Rev E
Removed Models 1X44B1 and 1X48B2
Added EMV Payment Systems wiring instructions Note: Coming Soon
M
8/7/18
Added “Note” to Data Communication Wiring per UL
N
3/12/19
Add Model 1X53M1 and 1X56M2
Remove Ethernet and 2-Wire Description
Update Standard Footprint to Rev K & Extended Blender Footprint to Rev G
Update Wiring Diagrams to Rev F

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456
USA 800-235-7618 ~ Outside USA 231-798-1310
[e-mail] ~ www.bennettpump.com

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456
USA 800-235-7618 ~ Outside USA 231-798-1310
[e-mail] ~ www.bennettpump.com

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456
USA 800-235-7618 ~ Outside USA 231-798-1310
[e-mail] ~ www.bennettpump.com
PCI SSC’s approval only applies to PEDs that are identical to the PED tested by a PCI Security Standards Council
recognized laboratory. If any aspect of the PED is different from that which was tested by the laboratory - even if the
PED conforms to the basic product description contained the letter, then the PED model should not be considered
approved, nor promoted as approved. For example, if a PED contains firmware, software, or physical construction that
has the same name or model number as those tested by the laboratory, but in fact are not identical to those PED
samples tested by the laboratory, then the PED should not be considered or promoted as approved.
No vendor or other third party may refer to a PED as “PCI Approved” nor otherwise state or imply that PCI SSC has, in
whole or part, approved any aspect of a vendor or its PEDs, except to the extent and subject to the terms and
restrictions expressly set forth in a written agreement with PCI SSC, or in an approval letter. All other references to PCI
SSC’s approval are strictly and actively prohibited by PCI SSC.
When granted, an approval is provided by PCI SSC to ensure certain security and operational characteristics important
to the achievement of PCI SSC’s goals, but the approval does not under any circumstances include any endorsement
or warranty regarding the functionality, quality, or performance of any particular product or service. PCI SSC does not
warranty any products or services provided by third parties. Approval does not, under any circumstances, include or
imply any product warranties from PCI SSC, including, without limitation, any implied warranties of merchantability,
fitness for purpose or noninfringement, all of which are expressly disclaimed by PCI SSC. All rights and remedies
regarding products and services, which have received an approval, shall be provided by the party providing such
products or services, and not by PCI SSC or the payment brand participates.
PCI SSC Legal Terms and Conditions

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456
USA 800-235-7618 ~ Outside USA 231-798-1310
[e-mail] ~ www.bennettpump.com
Page Intentionally Left Blank

Bennett Pacific eNVy Series Installation Manual Table of Contents
i
Bennett Limited Warranty for Product Installed in the United States –Pacific eNVy & XB Series
Bennett International Limited Warranty for Dispensers and Pumps
PCI SSC Legal Terms and Conditions
Safety Instructions iii
Introduction 1
Related Documents........................................................................................................................................................................................................1
Power Requirements .....................................................................................................................................................................................................1
Environmental Requirements ....................................................................................................................................................................................1
Dimensions........................................................................................................................................................................................................................1
Codes and Standards ....................................................................................................................................................................................................1
Recommended Equipment and Materials............................................................................................................................................................2
Customer Supplied Materials ....................................................................................................................................................................................2
Abbreviations and Acronyms.....................................................................................................................................................................................3
Determining the Number of Product Supply Pipes Needed........................................................................................................................6
Determining the Correct Position of the Product Supply Pipes .................................................................................................................7
General Installation 10
General Installation Information............................................................................................................................................................................ 10
Underground Installation Requirements ........................................................................................................................................................... 10
Existing Installations Receiving New Dispensers........................................................................................................................... 10
Plumbing Requirements ........................................................................................................................................................................................... 10
Pipelines and Dispenser-Containment Sumps ............................................................................................................................... 11
Dispenser Containment Sumps............................................................................................................................................................. 11
Shear Valve Installation (Remote Dispensers) ................................................................................................................................ 12
Determining Stub Up Positions in the Containment Sump ...................................................................................................... 12
How to Lift and Transport the Pacific eNVy Series........................................................................................................................................ 13
Dispenser Mounting Instructions.......................................................................................................................................................................... 14
Pacific eNVy 919 Electronics Standard Installation Diagram - Footprint............................................................................................. 14
Pacific eNVy 919 Extended Blender Installation Diagram –Footprint .................................................................................................. 16
Wiring Installation 19
Determining the Number of Wires Required................................................................................................................................................... 19
Step 1 –Dispenser Power........................................................................................................................................................................ 19
Step 2 –Communications Wiring ........................................................................................................................................................ 19
Step 3 –Remote Dispensers (Submerged Pump) Wiring.......................................................................................................... 20
General Wiring Requirements ................................................................................................................................................................................ 21
Beginning the Wiring Process ................................................................................................................................................................................ 21
Instructions for Earth Grounding Equipment................................................................................................................................................... 22
AC Power Installation................................................................................................................................................................................................. 22
Electronic Power Connections................................................................................................................................................................................ 22
Rules to Ensure Proper Operation........................................................................................................................................................................ 22
Connecting Submersible Pump Motor Power for Remote Dispensers................................................................................................. 23
Data Communication Wiring .................................................................................................................................................................................. 24
Current Loop Fuel Wire Termination: (Current Loop Personality Module TS1 & TS2).................................................. 24
Generic Current Loop Fuel Wire Termination: (Current Loop Personality Module TS1 & TS2)................................. 25
RS-485 Fuel Wire Termination: (RS-485 Personality Module TS1)......................................................................................... 25
RS-485 Card Reader Wire Termination: (Upper 819 CPU Board TS3)................................................................................... 25
RS-485 Card Reader Wire Termination: (Upper 919 CPU Board TS1)................................................................................... 25
Table of Contents

Bennett Pacific eNVy Series Installation Manual Table of Contents
ii
Installing the Wire Separator.................................................................................................................................................................................. 26
Battery (DC Power) Installation.............................................................................................................................................................................. 26
Dispenser Start-Up...................................................................................................................................................................................................... 27
Before applying AC power to the dispenser, follow this procedure: .................................................................................... 27
Turn on 115 or 230 Volts circuit breaker to supply AC electronic power to the unit: ................................................... 27
Checking the Submersible Pump Motor Circuit ............................................................................................................................ 28
Replace the Safety Covers........................................................................................................................................................................................ 28
Purging Air from Remote Dispensers.................................................................................................................................................................. 28
Wiring Diagrams 29
Current Loop Communication................................................................................................................................................................................ 29
Generic Current Loop Communication............................................................................................................................................................... 30
RS-485 Communication ............................................................................................................................................................................................ 31
Wiring Diagram Notes............................................................................................................................................................................................... 32
Final Installation Checklist 33
Information Resources 34
Pacific eNVy Site Audit Report 1
Table of Contents

Bennett Pacific eNVy Series Installation Manual Safety Instructions
iii
Safety Instructions
For safe installation of this equipment, read and understand all dangers, warnings, and cautionary information. Save
this safety information in a readily accessible location. Look for the following warnings throughout the manual:
Red and White “DANGER” means: If you do not follow the instructions, severe injury or death will occur.
Orange and Black “WARNING” means: If you do not follow the instructions, severe injury or death can occur.
Yellow and Black “CAUTION” means: If you do not follow the instructions, damage can occur to the dispenser.
Blue and White “IMPORTANT” means: Helpful tips and other recommendations on equipment installation,
usage, and maintenance should be observed.
DANGER PELIGRO DANGER
FIRE, EXPLOSION, INJURY, OR DEATH WILL OCCUR IF FUEL FILTERS ARE CHANGED BY
UNTRAINED PERSONNEL. MAKE SURE, ONLY TRAINED PERSONNEL CHANGE FILTERS.
TO PREVENT INJURY TO YOU FROM VEHICLES AND ONLOOKERS, ALWAYS PLACE A
BARRIER AROUND THIS EQUIPMENT BEFORE PERFORMING SERVICE OR MAINTENANCE.
GASOLINE AND FUEL ETHANOL IS FLAMMABLE. NO SMOKING OR OPEN FLAME.
FUEL ETHANOL IS POISONOUS AND SHOULD NOT BE INGESTED.
DENATURED ETHANOL FOR BLENDING E85 OR OTHER ETHANOL BLENDS SHOULD NOT BE
STORED DUE TO THE RISK OF EXPLOSION.
DISCONNECT ALL POWER TO THIS EQUIPMENT AND ASSOCIATED SUBMERGED PUMP(S)
DURING INSTALLATION, SERVICE, OR ANY MAINTENANCE I.E., CHANGING FILTERS.
WARNING ADVERTENCIA MISE EN GARDE
You must have training in the installation, service, or maintenance of this equipment (dispenser,
pump, console, control box, or submerged pump) before working on it. Maintenance repairs must
be done by authorized personnel only. Warranty work may only be performed by Bennett certified
technicians.
To prevent electric shock, keep the electrical parts of the dispenser dry.
Electronic components are static sensitive. Use proper static precautions (e.g. static straps) before
working on the equipment.
The emergency shut-off valve (also called the fire valve, shear valve, or impact valve) must be
closed when service or maintenance is performed on this equipment.
You must have training in the operation and programming of this dispenser before using it. READ
THE OPERATORS MANUAL.
Make sure this equipment is correctly grounded. Failure to do will cause injury or damage
equipment or improper operation. Improper grounding voids the warranty.
When anchoring the dispenser, always level the dispenser with shims before bolting to the island.
DO NOT shim the middle of base rails to bolt down the dispenser.
CAUTION PRECAUCIÓN MISE EN GARDE
Do not drill holes in fuel dispensers. Holes can cause failure of the electronic equipment. THE
WARRANTY WILL BECOME VOID. Use only adhesive backed sign mounting brackets.

Bennett Pacific eNVy Series Installation Manual Safety Instructions
iv
IMPORTANT IMPORTANTE IMPORTANT
All trained technicians must work in accordance to all requirements, standards, and guidelines
specified by the suppliers Environmental Standards® Health, Safety, Security & Environment
(HSSE) policies. Note: Bennett Pump highly recommends all technicians observe HSSE policies
defined by the supplier. Bennett Pump does not impose any restrictions or additional
requirements contained in Environmental Standards® Health, Safety, Security & Environment
(HSSE) policies.
!! READ AND UNDERSTAND ALL WARNING LABELS ATTACHED TO THE DISPENSER !!
Safety Instructions

Bennett Pacific eNVy Series Installation Manual Introduction
1
Introduction
This manual contains installation instructions for installing the Pacific eNVy Series dispenser. Included are mechanical,
transporting, wiring, and start-up instructions. Please refer to the original manufacturer’s installation instructions for
proper installation on underground liquid storage systems, shear valves, hoses, and breakaways.
Related Documents
Bennett 515 Pump Controller Installation & Service Manual---------------------------------------------Part# 105022
Bennett Pacific eNVy Series Operators Manual -----------------------------------------------------------Part# 128503
Bennett Pacific eNVy Series Parts Manual ----------------------------------------------------------------Part# 128504
Pacific eNVy Maintenance Schedule and Log-------------------------------------------------------------Part# 130886
Pacific eNVy Series Audit Report -------------------------------------------------------------------------Part# 112827
Simply Secure Payment PCI 3.1 (SSP Color) Programming, Service, and Part Manual ------------------Part# 124184
Simply Secure Payment PCI 3.1 (SSP Large Display) Programming, Service, and Parts Manual --------Part# 128203
Simply Secure Payment (SSP Large Display w/ SBC2) Programming, Service, and Parts Manual -------Part #132544
Power Requirements
AC Power Input, Electronic ..........................................................................................................120/240 VAC, 50/60 Hz. 350 Watts Max.
DC Power Supply Output ....................................................................................................................................... +12 VDC at 2.0 Amps Max.
+24 VDC at 2.0 Amps Max.
Lead-Acid Battery Output ......................................................................................................................................+12 VDC at 5.0 Amp Hours
Nickel-Cadmium Battery Output.............................................................................................................. +3.6 VDC at 250 Milliamp Hours
Environmental Requirements
Operating Temperature Range............................................................................................................. -40°C to +65°C (-40°F to +150°F)
Humidity...............................................................................................................................................................................0-95% non-condensing
Dimensions
1000 eNVy Series Maximum ................................................................................................... * 49” (width) x 22” (depth) x 91” (height)
*without valance
1000 eNVy Series Base ...................................................................................................................43 3/8” (width) x 15 1/8” (depth) - INSIDE
44 ½” (width) x 19 ¼” (depth) - OUTSIDE
1000 Extended Blender Series Maximum .......................................................................... * 65” (width) x 22” (depth) x 90” (height)
*without valance
1000 Extended Blender Series Base ...................................................................................52 3/16” (width) x 14 13/16” (depth) - INSIDE
52 5/8” (width) x 20 5/16” (depth) - OUTSIDE
1000 Series Estimated Shipping Weight..........................................................................................................650 pounds/295 kilograms
Codes and Standards
NFPA 30 – Flammable and Combustible Liquids Code
NFPA 30A – Code for Motor Fuel Dispensing Facilities and Repair Garages
NFPA 70 – National Electric Code®
ASME B31.3 – Process Piping
International Fire Code – 2000 Edition

Bennett Pacific eNVy Series Installation Manual Introduction
2
Recommended Equipment and Materials
IMPORTANT: Any alternative fuel dispenser must only use UL (Underwriters’ Laboratories, Inc.) Listed
equipment (hoses, nozzles, shear valves, filters, pipe sealants, and breakaways) for fueling.
Anchor Bolts
Any additional installation equipment and/or tools required for (hanging hardware, nozzles, hoses, valance, etc.)
Any optional kits (hanging hardware, valance, etc.)
Classified Pipe Joint Sealing Compound
Fasteners (e.g. cable tie, zip tie)
Lift Straps
Lifting device to lift and transport the dispenser.
Minimum Schedule 40 Steel Inlet Pipe
Multi-Meter
Personal Barriers
Potting Compound National Fire Protection Agency NFPA 70: National Electrical Code (NEC) approved.
Static Straps
Voltmeter
Customer Supplied Materials
DANGER: IMPACT SAFETY VALVES ARE TO BE INSTALLED WITH SHEAR SECTION IN LINE WITH
SURFACE OF ISLAND WITHIN + ¾”. DEPENDING ON VALVE TO BE USED A LONGER OR
SHORTER INLET NIPPLE MAY BE REQUESTED.
CAUTION: Dispenser must be installed with provisions for expansion relief, which will relive at
pressures not exceeding 50psi (345MPa). Do not use line check valve between dispenser
and tank unless provided with relief valve.
CAUTION: Use only UL Listed Rigid metal conduit and UL listed sealing fittings with conductor seals.
The following items are to be supplied by the customer.
A minimum of 4 bolts with a minimum diameter of ½”.
Conduit
Fittings to Electrical and Plumbing Inlets
Ground Joint Union
Inlet Pipes 1-1/2”, Threaded for Inlet Manifold (NPT Thread)
Introduction

Bennett Pacific eNVy Series Installation Manual Introduction
3
Abbreviations and Acronyms
Term
Description
AC
Alternating Current
API
America Petroleum Institute
DC
Direct Current
DIN
Dispenser Identification Number
E10
10% ethanol, 90% gasoline
E15
15% ethanol, 85% gasoline
E85
An ethanol/gasoline blend containing 51% to 83% ethanol
EPA
Environmental Protection Agency
Hz
Hertz
IFC
International Fire Code
NEC
National Electrical Code
NFPA
National Fire Protection Agency
NPT
National Pipe Taper
National Pipe Thread
NREL
National Renewable Energy Laboratory
OEM
Original Equipment Manufacturer
OSHA
Occupational safety and Health Administration
PEI
Petroleum Equipment Institute
PVC
Polyvinyl Chloride
STP
Submersible Turbine Pump
THHN
Thermoplastic High Heat-resistant Nylon-coated
TIA/EIA
Telecommunications Industry Association/Electronic Industries Alliance
UL
Underwriters Laboratories, Inc.
UST
Underground Storage Tank
VAC
Voltage Alternating Current
VDC
Voltage Direct Current
VOM
Volt-Ohm meter
Introduction

Bennett Pacific eNVy Series Installation Manual Introduction
4
Determine the model number of the dispenser from the serial tag located inside the unit on side 1 on the electronics
deck. Utilizing the chart below determine the features of the dispenser to be installed. Understanding the features of
the dispenser to be installed will be helpful in understanding the proper installation of the dispenser.
How a model for the Pacific eNVy Series dispenser is made up.
Introduction
Figure 1 –Spec. 100 DIN Sheet

Bennett Pacific eNVy Series Installation Manual Introduction
5
SPEC. 200
Introduction
Figure 1a –Spec. 200 DIN Sheet

Bennett Pacific eNVy Series Installation Manual Introduction
6
Determining the Number of Product Supply Pipes Needed
Determine the dispenser’s model number from the serial tag located on side 1 inside the unit on the deck. Locate the
model number in the table below to determine the number of product pipes required.
Step 1 The dispenser will require a submerged pump and pressurized supply line for each product.
Step 2 Determine the number of product pipes required by finding the model number below. Note: The use of X
in the model number indicates a field where the entry in not important to this discussion.
Model Number
(Side 1 or Side 2)
Product Supply Lines Required
Chassis
(outside width)
1X11N1-XXXX
1X12N2-XXXX
Use 1 product line plumbed to inlet position A
44 ½”
1X21M1-XXXX
1X22M2-XXXX
Use 1 product line plumbed to inlet position A
Use 1 product line plumbed to inlet position C
44 ½”
1X22N1-XXXX
1X24N2-XXXX
Use 1 product line plumbed to inlet position B
Use 1 product line plumbed to inlet position C
44 ½”
1X22N2-XXXX
Use 1 product line plumbed to inlet position A
Use 1 product line plumbed to inlet position C
44 ½”
1X31B1-XXXX
1X32B2-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
Use 1 product line plumbed to inlet position C for high-grade product
44 ½”
1X31M1-XXXX
1X32M2-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
Use 1 product line plumbed to inlet position B for middle grade product
Use 1 product line plumbed to inlet position C for high-grade product
44 ½”
1X33N1-XXXX
1X36N2-XXXX
Use 1 product line plumbed to inlet position A for mid-grade product
Use 1 product line plumbed to inlet position B for high-grade product
Use 1 product line plumbed to inlet position D for low-grade product
52 5/8”
1X41B1-XXXX
1X42B2-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
Use 1 product line plumbed to inlet position C for high-grade product
44 ½”
1X42B1-XXXX
1X44B2-XXXX
Use 1 product line plumbed to inlet position A for low grade product
Use 1 product line plumbed to inlet position C for high-grade product
Use 1 product line plumbed to inlet position B non-blended product
44 ½”
1X42M1-XXXX
1X44M2-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
Use 1 product line plumbed to inlet position B for mid-grade product
Use 1 product line plumbed to inlet position C for non-blended product
Use 1 product line plumbed to inlet position D for high-grade product
52 5/8”
1X51B1-XXXX
1X52B2-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
Use 1 product line plumbed to inlet position C for high-grade product
44 ½”
1X56B1-XXXX
1X56B2-XXXX
Use 1 product line plumbed to inlet position A, for low-grade product
Use 1 product line plumbed to inlet position B for non-blended product
Use 1 product line plumbed to inlet position C for alternative product
Use 1 product line plumbed to inlet position D for high grade
52 5/8”
1X56E1-XXXX
1X56E2-XXXX
Use 1 product line plumbed to inlet position A for low-grade and alternative product
Use 1 product line plumbed to inlet position B for high-grade product
Use 1 product line plumbed to inlet position D for alternative product
52 5/8”
1X53M1-XXXX
1X56M2-XXXX
Use 1 product line plumbed to inlet position A, for low-grade product
Use 1 product line plumbed to inlet position B for non-blended product
Use 1 product line plumbed to inlet position C for alternative product
Use 1 product line plumbed to inlet position D for high grade
52 5/8”
Introduction

Bennett Pacific eNVy Series Installation Manual Introduction
7
Determining the Correct Position of the Product Supply Pipes
The diagrams shown in Figure 2, Figure 3, and Figure 4 indicates the relationship of the product inlets to the nozzle
boots. Find the model number of the dispenser you are installing shown on the previous page and determine the
number of product inlets and their location. Exact inlet locations can be found on the base diagrams (footprints) later
in this manual. Note: UL Listed ethanol equipment must be used if an alternative fuel product is being dispensed.
Introduction
Figure 2 - Product Supply Positions View 1

Bennett Pacific eNVy Series Installation Manual Introduction
8
Introduction
Figure 3 –Product Supply Positions View 2

Bennett Pacific eNVy Series Installation Manual Introduction
9
Introduction
Figure 4 - Product Supply Positions View 3

Bennett Pacific eNVy Series Installation Manual General Installation
10
General Installation
General Installation Information
Examine the shipment immediately upon arrival to make certain there has been no damage or loss in transit. Bennett
Pump Company, as shipper, is not liable for the hazards of transportation. Please make damage claims directly to the
truck line.
Please read these instructions carefully and read all tags attached to the dispenser before starting installation. A
dispenser that is not properly installed will not perform properly and will void the limited warranty. All other
equipment manufacture’s installation instructions must be followed. Bennett Pump does not provide other
manufacture’s installation instructions and are not responsible for any potential problems
Installation must be in accordance with the National Fire Protection Agency NFPA 70: National Electrical Code (NEC),
NFPA 30A: Code for Motor Fuel Dispensing Facilities and Repair Garages, NFPA 30: Flammable and Combustible Liquids
Code, International Fire Code (IFC), and all state and local codes.
For complete reference instructions for installing underground liquid storage systems, order “Recommended Practices
for Installation of Underground Liquid Storage Systems” from the Petroleum Equipment Institute, P.O. Box 2380, Tulsa,
OK 74101 or at http://www.pei.org.
For complete reference instructions for installing underground liquid storage, systems when storing biofuels above
E10 or B20 refer to the EPA’s Office of Underground Storage Tanks guidance document, “Compatibility of
Underground Storage Tank Systems with Biofuels Blends” from the Office of Underground Storage Tanks, Washington,
D.C. 20460 or at http://www.epa.gov/oust.
Underground Installation Requirements
All installation specifications may vary from different locations. In all cases, the installation must be in accordance with
all National Electrical Codes, State, and Local Codes.
All installations must be performed by a technician who is trained and licensed in accordance to all codes, standards,
and regulations.
Installation of the Bennett product and all accessories (i.e. Nozzles, Hoses, and Breakaways) must be performed by a
technician who is trained and licensed in accordance to all codes, standards, and regulations.
Existing Installations Receiving New Dispensers
When a new dispenser is attached to an old underground installation, the tanks should be cleaned and tested for
leaks. Any water accumulation in the tank must be removed. Bennett Pump is not responsible for any damage to the
dispenser or for improper operation due to accidents, abuse, or faulty installation. We require installing new wires in
the underground metal conduits to validate the equipment warranty.
Plumbing Requirements
All piping must be clean of foreign debris such as oil, grease, and shavings. All connections must be liquid tight to
prevent leaks. Refer to the footprint diagrams for tube sizes and additional information.
All piping shall be supported and protected against physical damage, including damage from stresses arising from
settlement, vibration, expansion, or contraction.
Alternative fuels, such as E25, E85, and other ethanol blends, may require special piping materials or components.
Consult the piping manufacturer to determine if the piping material, fittings, and connectors are compatible with the
alcohol-blended fluid being used.