BLK BOX Goliath User manual

170kg
OWNERS MANUAL & QUICK START GUIDE
DOUBLE HALF RACK GOLIATH
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
PRODUCT SPECIFICATION
21-0110-0G
#MADEINBELFAST
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
-125kg
300kg
1200mm x 2408mm x 980mm
-
-
-
-2700mm x 3272mm x 3580mm
2
-

WARNING
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
PARTS & ATTACHMENTS
No. Name SKU QTY
1 2.4 UPRIGHT DNA60
WITH FEET
21-0036-0A 6
2 1.2 DOUBLE BRANDING
BOX CM DNA60
21-0018-0D 1
3 1.2 BOX CM DNA60 21-0013-0A 2
4 0.4 BOX CM DNA60 21-0036-0A 4
5 0.4 BOX & BAR CM
DNA60
21-0009-0A 4
6 MULTIGRIPS DNA60 21-0151-0A 1
7 M10X80 SLEEVE
ANCHOR
10-0031 18
8 M10X90 BOLT 10-0008 102
9 M10 NYLOCK NUT 10-0024 102
10 M10 FLAT WASHER 10-0019 120
11 J-HOOKS PAIR 16-0001 1
1
2
3
4
11
7
8
910
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS ENSURE
BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER REDUCE RISK OF
INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE).
WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT.
EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS LEVEL
OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
6
5
xx
Nm

ASSEMBLY
x
8
x
4
1
BOLT 1QTY 1.2 DOUBLE BRANDING BOX (21-0018-0D] AND 1QTY 1.2 BOX (21-0013-0A)
BETWEEN 2QTY UPRIGHTS (21-0036-0A) WITH BOLTS ASSEMBLY AS SHOWN.
ENSURE LOGOS ON UPRIGHTS ARE FACING OUTWARDS AND ALL BOLTS FACING
INWARDS.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST

2
BOLT 1QTY 1.2 BOX (21-0013-0A) BETWEEN 2QTY UPRIGHTS (21-0036-0A) AND CONNECT TO
EXISTING ASSEMBLY USING 2QTY 0.4 BOX & BAR (21-0009-0A) AND 2QTY 0.4 BOX (21-0036-0A)
WITH BOLT ASSEMBLY AS SHOWN. BOLT 1QTY MULTIGRIPS (21-0151-0A) TO 1QTY 1.2 BOX
(21-0013-0A) WITH BOLT ASSEMBLY AS SHOWN ENSURE LOGO ON UPRIGHTS ARE FACING
OUTWARDS AND BOLTS ARE FACING INWARD.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST
10.0008
10.0019 x2
10.0024

x
4
x
4
x
4
x
8
x
6
x
8
3
BOLT 1QTY 1.2 BOX (21-0013-0A) BETWEEN 2QTY UPRIGHTS (21-0036-0A) AND CONNECT TO
EXISTING ASSEMBLY USING 2QTY 0.4 BOX & BAR (21-0009-0A) AND 2QTY 0.4 BOX (21-0036-0A)
WITH REUSED BOLT ASSEMBLYS AS SHOWN. BOLT 1QTY MULTIGRIPS (21-0151-0A) TO 1QTY 1.2 BOX
(21-0013-0A) WITH BOLT ASSEMBLY AS SHOWN ENSURE LOGO ON UPRIGHTS ARE FACING
OUT AND BOLTS ARE FACING INWARD.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024

x
6
x
1
2
30
Nm
4
TIGHTEN ALL BOLT ASSEMBLIES WITHIN THE CIRCLE TO SPECIFIED TORQUE. ENSURE ALL
UPRIGHTS ARE PLUMB. DRILL AND SECURE THE MIDDLE HOLE ON EACH UPRIGHT AS SHOWN
IN GUIDE. REMOVE ALL BOTTOM CROSSMEMBERS, DRILL AND SECURE REMAINING HOLES ON
UPRIGHTS AS SHOWN IN GUIDE. REATTACH THE BOTTOM CROSSMEMBERS .
10.0031
10.0019
VACUUM
HAMMER
IN BOLT
10.0031
10.0019
SLEEVE ANCHOR
BOLT FITTING
-DRILL
10MM HOLE
THROUGH
FLOOR
COVERING,
90MM DEEP
USING PLATE
AS A GUIDE.
-VACUUM
OUT THE
DUST.
-HAMMER
SLEEVE
ANCHOR
DOWN INTO
THE HOLE.
-TIGHTEN
SLEEVE
ANCHOR TO
SPECIFIED
TORQUE
USING 13MM
SPANNER.
#MADEINBELFAST
xx
Nm
90MM
DRILL
HOLE
TIGHTEN
x50

#MADEINBELFAST
5
TIGHTEN ALL BOLT ASSEMBLIES WITHIN THE CIRCLE TO SPECIFIED TORQUE.
30
Nm
x30

#MADEINBELFAST
1:1 SCALE FASTENERS
FOR TERMS AND CONDITIONS VISIT OUR WEBSITE AT
www.blkboxfitness.com/pages/terms-conditions
GET IN TOUCH
TEL: [phone]
EMAIL: [e-mail]
DISCOVER MORE AT:
www.blkboxfitness.com
M10x80 SLEEVE ANCHOR
10-0031
NYLOCK NUT
10-0024
M10 FLAT WASHER
10-0019
M10x90 BOLT
10-0008