Bpt GSM/i10K User manual

GSM/i10K GSM INTERCOM
Installation Manual
NEW INSTRUCTIONS

11
12
21
5
521 8 1112 14
USB
Connector
GSM INTERCOM
Gate station unit (typically on gooseneck)
11
12
6
G
21
5
screened
G12 6 21 511
12 VDC (13.8)
-
+
Rel 1 Rel 2 Rel 3
Rel 4
Keypad
up to 20m
GSM INTERCOM
Gate station unit (typically on gooseneck)
join at audio module side
(recommended)
521 8 1112 5
Dial No. 2
Dial No. 3
Dial No. 1
4 Button
12V
NOTE: All relays are normally open contacts Page 1
Antenna connector
M000042
USB
Connector
12 VDC (13.8)
-
+
Rel 1 Rel 2 Rel 3
Rel 4
Antenna connector
G12 6 21 511 7
7
Dial No. 4
MicroSIM
Slide and
open hinge
MicroSIM
Slide and
open hinge
up to 20m

11
12
21
5
GSM INTERCOM
11
12
6
G
21
5
Two gate stations
NOTE: All relays are normally open contacts
11
12
21
5
11
12
6
G
21
5
521 8 1112 14 521 8 1112 14
up to 20m
A B
To add two gate stations configure each
keypad as A or B. This is done by holding (about 2seconds)
* and 0 for A or # and 0 for B when applying
power to the keypad. confirmation can be heard
by a beep and an orange illuminated LED.
There after send the following SMS to the unit:
*2222 DUAL 1 where 2222 is your password.
to Disable Dual gate station:
*2222 DUAL 0 where 2222 is your password.
NB!!!
Page 2
USB
Connector
G12 6 21 511
12 VDC (13.8)
-
+
Rel 1 Rel 2 Rel 3
Rel 4
Antenna connector
7
MicroSIM
Slide and
open hinge
GSM/i10K

GSM INTERCOM
11
12
21
5
11
12
6
G
21
5
1
2
Access control
The gatestation with access control module is now equipped with the ability to trigger the relays on
the GSM master board by entering in a password on the keypad. This is useful in the case where
entry and exit maybe be provided to home owners and guests, in addition to the missed call feature
of the intercom.
Programming access control
2. A beep will be heard which signifies programming mode.
4. Press the red *
1. To enter programming mode enter 1 2 3 4 5 and hold down the red * button
The unit has now exited from programming mode and the programmed password may be used by pressing the
password followed by the green #.
2. All numbers less than 4 characters are interpreted as a unit number, therefore choose a password of 5
numbers or more for access control.
All passwords for access control are programmed via the keypad. Four passwords may be programmed to activate the
respective four relays on the GSM master board.
(1 2 3 4 5 is the default master password).
3. Press numbers 1 - 4 to program the password for relays 1 - 4
5. Enter the password (up to 8 numbers) and press the red*
6. An acknowledgment tone will be heard.
1. Password 1 is the also master password - changing this will change the programming password.
NOTES:
3. If an incorrect password is entered 3 times the keypad will prevent any input for the following 20 seconds.
Reactivation is indicated by a beep.
Resetting the master password:
4. A single invalid tone indicates an unprogrammed unit number has been entered
5. A double invalid tone indicates an invalid access control password has been entered
1. Hold down the numbers 1 9 while applying power until a beep is heard.
2. Enter in the new password followed by the green # button
3. Power-cycle the unit
Page 3
GSM/i10K
M000042

CONNECTING A HANDSET
5
7
8 9
11
12
6
G
21
5
9 8 52165
330e
47e 100uF
+
Connection unit
may be purchased
from supplier
Page 4
M000042
USB
Connector
G12 6 21 511
12 VDC (13.8)
-
+
Rel 1 Rel 2 Rel 3
Rel 4
Antenna connector
7
MicroSIM
Slide and
open hinge
GSM/i10K

The GSM intercom may have up to a 4 digit number (9999 max)
The unit will give and audible message acknowledging that the call is in progress. If an unprogrammed unit is dialed, an error message will be heard.
NB: all numbers added must contain the country code ie, 27821234123 and no +’s
Should the caller wish to cancel the phone call at any stage they may press either of the dial buttons to hung up.
The unit may be programmed via PC software through the USB port or via SMS.
On power up all LEDs will be on. As the unit passes the various tests the LEDs will turn off.
Remove the USB cable after programming and the unit will proceed with the boot sequence.
Booting sequence
Only when the green and blue LEDs are flashing slowly is the unit in the normal running state. “System ready” audio notification will be played through the
gatestation.
Please note that if the unit is connected to a computer via the USB cable, none of the SMS or dialing capabilities will work.
Programming
The following are the structure of the SMSs for the various programming options. The default password is 2222 and must be changed. All messages start
and end with a * (asterisk)
Add airtime: *2222 NETW XXXXXXXXXXX
eg *2222 NETW *136*01*12345678912345#
where XXXXXXXXXX is the recharge USSD Command and voucher pin
Retrieve airtime available: *2222 NETW XXXXXX
where XXXXXXX is the USSD command from the network
eg. *2222 NETW *136#*
Set automatic hang-up time to 60s: *2222 HANG XX*
Set the status number: *2222 STAT 27821234123
Change password from 1234 to 7788: *2222 PASS 7788
XX - hangup time seconds (25 seconds default)
Each unit may have two numbers associated with it. By pressing the unit number and either the * or # dial buttons the associated number will be dialed. (# for
number 1 and * for number 2)
The status number will SMS’d on a weekly basis
Adding & Calling numbers (Keypad Version)
At any point during the conversation the home owner may key in on their keypad the number 1 or 2 or 3 or 4. This will activate one of the 4 relays at the unit
respectively which will typically trigger the gate to be opened.
*2222 ADDN AAAAAAAAA,BBBB,C,D
D - missed call permission (1- relay1, 2 relay2)
Examples
BBBB - unit number 1-9999
AAAAAAAAA - telephone number eg 27821231234
Missed-call activation
Add number 2 for unit 123 and allow missed call relay 1: Add number 1 for unit 32 and allow missed call relay 2:
Gate triggering
Clear telephone list: *2222 CLRN
*2222 ADDN 27821234123,123,2,1 *2222 ADDN 27821234123,32,1,2
C - user number 1,2
Remove a number: *2222 DELN 27821234123
The GSM unit comes equipped with a missed call function. Only programmed numbers may activate this function. When the caller phones the number of the
SIM card in the GSM intercom, the unit will proceed to hang up the called and activate relay 1 and no charge to the caller.
Page 5
PROGRAMMING
M000042
GSM/i10K