Bradley S19-310AC User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-163AC Rev. C; ECN 17-05-039
© 2017 Bradley
Page 1 of 13 7/18/2017
S19-310AC
Combination Drench Shower and
Eye/Face Wash
Combiné douche oculaire/faciale
Combinación de ducha de aspersión
y lavador de ojos/rostro
Table of Contents
Pre-Installation Information ............................................................ 2
Supplies Required...........................................................................3
Secure base to floor........................................................................3
Assemble components....................................................................3
Connect water supply......................................................................3
Assembly of Components ...............................................................4
Parts List .........................................................................................5
Table des matières
Avant l’installation........................................................................... 6
Equipements nécessaires...............................................................7
Fixation de la bride au sol...............................................................7
Assemblage des composantes .......................................................7
Raccordement de l’alimentation en eau..........................................7
Assembage des composantes........................................................8
Liste des piéces ..............................................................................9
Contenido
Información previa a la instalación............................................... 10
Materiales necesarios ...................................................................11
Fijar la base al piso.......................................................................11
Montar los componentes...............................................................11
Conectar el suministro de agua ....................................................11
Armado de los componentes ........................................................12
Lista de piezas ..............................................................................13

2
S19-310AC Installation
7/18/2017 Bradley • 215-163AC Rev. C; ECN 17-05-039
WARNING
Flush the water supply lines before beginning installation and after installation is complete. Test
the unit for leaks and adequate water flow. Main water supply to the eyewash should be “ON” at all
times. Provisions shall be made to prevent unauthorized shutoff.
CAUTION
Emergency equipment must be supplied with tepid water (60°F to 100°F/15.6°C to 37.8°C). Any
prolonged exposure to near freezing water affects the body's ability to maintain body temperature,
increasing the risk of hypothermia.
NOTICE
Before installing this product, ensure that there are adequate clearances around the product and
activation of the product does not interfere with other products or obstructions.
Avoid cleaners containing organic solvents, alcohols and hydrocarbons. Rinse with water after
cleaning.
IMPORTANT
The installation and location of all safety drench showers, eye and eye/face washes must comply
with the requirements of ANSI/ISEA Z358.1.
Read this installation manual completely to ensure proper installation, then file it with the owner or
maintenance department. Compliance and conformity to drain requirements and other local codes
and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding any
packaging material. If any parts are missing, do not begin installation until you obtain the missing
parts.
The ANSI/ISEA Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley plumbed
emergency fixtures require a minimum of 30 PSI (0.21MPa) flowing pressure.
Self-closing spring-loaded valves are not UL classified to ANSI/ISEA Z358.1.
Weekly activation must be conducted on all plumbed emergency equipment to ensure a suitable
flushing fluid supply is present and any sediment build-up in the supply line is cleared. Emergency
equipment should be inspected monthly to address any maintenance issues ensuring the
equipment is in good operating condition and that there are no signs of wear.
Workers who may come in contact with potentially hazardous materials should be trained regarding
the placement and proper operation of emergency equipment per ANSI/ISEA Z358.1.
For questions regarding the operation or installation of this product, visit www.bradleycorp.com or
call 800-BRADLEY (272.3539).
Product warranties and parts information may also be found under ”Products” on our web site at
bradleycorp.com.

3
Installation S19-310AC
Bradley • 215-163AC Rev. C; ECN 17-05-039 7/18/2017
Supplies Required
• (3) 3/8" floor anchors and bolts
• Teflon tape and pipe sealant
• Piping to 1-1/4" NPT water supply inlet and 1-1/4" NPT
drain outlet on unit
• Adequate supply pipe supports
• Minimum 4" (102mm) drain to accommodate 30 gallons
(115 liters) per minute discharge for shower waste
• OPTIONAL: sign-mounting hardware
All dimensions assume standard thread
engagement. Variations in manufacturing
allow for +/- ¹⁄₈" (3mm) per threaded joint.
To find the tolerance of a dimension, add
the number of thread joints in between a
dimension and multiply it by ¹⁄₈" (3mm).
Top View From Bowl
25¼"
(641mm)
Ø 3¹⁄₁₀"
(79mm)
4½"
(114mm)
86"
(2184mm)
to Floor
65¾"
(1670mm)
to Floor
Ø 9" (229mm)
Flange with (3)
Ø ³⁄₈" (10mm)
Holes on Ø 8"
(203mm) Bolt
Circle
Ø 10¾"
(273mm)
10½"
(267mm)
9½"
(241mm)
36¹⁄₈"
(918mm)
to Floor
25-1/2"
(648mm)
6"
(152mm)
Local codes may require the installation of a backflow
prevention valve to complete proper installation.
Compliance with local codes is the responsibility of the
installer. Valve must be tested annually to verify that it
is functioning properly. Backflow prevention valves are
not included with the fixture and may be supplied by the
contractor or purchased from Bradley Corporation.
Secure base to floor
1. Install three suitable anchors (supplied by installer)
for 3/8" bolts in the floor.
2. Bolt the base to the floor anchors using 3/8" bolts
(supplied by installer).
Assemble components
1. Assemble the remaining unit components as shown
on page 4.
2. Apply pipe sealant (by installer) to all male-threaded
pipe joints.
3. Use the rubber grip pad provided or a strap wrench
around pipes when tightening to prevent marring.
Place the grip pad on the pipe, then put the wrench
over the grip pad and turn the pipe with the wrench.
4. When connecting the steel chain, first connect the
chain to the “S” hook on the foot treadle. Then, with
the foot treadle raised up, straighten the chain and
connect a link to the “S” hook on the valve handle.
Make sure the chain is pulled tight. The length of
chain will vary.
Connect water supply
NOTICE! Do not rely on Bradley’s Combination Unit
to support supply piping.
1. Connect water supply piping to 1¼" NPT inlet on unit
(piping by installer). Provide adequate supports (by installer)
for supply pipe using pipe hangers or other means.
2. Connect drain piping to 1¼" NPT drain outlet on unit (piping
by installer).
3. Hang the safety sign from the unit with the curtain hooks
provided (or mount it to the wall using sign-mounting
hardware by installer).
Bottom edge of the showerhead should be 86"
(2184mm) from floor.

4
S19-310AC Installation
7/18/2017 Bradley • 215-163AC Rev. C; ECN 17-05-039
Assembly of Components
10
P.O. BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FA X:(262-251-5817)
http://www.bradleycorp.com
114-052
P.O. Box 309, Menomonee Falls,WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1STWÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chosequi ne va pas fait
un rapport immédiatement.
14
21.3
21.11
21.1
21.2
25
26.2
26.3
26.4
26.3
26.5
26.1
26.6
24
21
26
24.3
6
24.5
24.4
24.2
24.1
5
27
17
4
3
20
2
22
15
19
7
1
10.31
10.2
10.4
28
3
2
8
9
23 17
2
11
12
13
10.3
10.5
25.1
25.2
25.3
20 18
20
21.4
Items 10.1–10.5 come preassembled as Item 10.
Items 24 and 25 come preassembled.
1¼" NPT
Supply Inlet
1¼" NPT
Drain Outlet
If tee (Item 7) is used as a supply inlet,
use plug (Item 8) on tee (Item 2)
Optional 1-1/4" NPT Supply
Inlet (best for rigid support)
NOTE: Use
teflon tape
only.

5
Installation S19-310AC
Bradley • 215-163AC Rev. C; ECN 17-05-039 7/18/2017
Parts List
Prepack S30-071 includes items 21.11, 21.2, 21.3, 21.4
Prepack S45-1789 includes items 24.2, 24.4, 24.5
Item Part No. Qty. Description
1 131-059 1 Base
2 169-727 3 Pipe Tee 1¼" NPT
3 113-006LW 2 Pipe 1¼" NPT x 22½"
4 S06-136 1 Plugged Nipple 1¼" NPT x 3"
5 169-841 1 Reducing Tee
6 113-006LC 1 Pipe 1¼" NPT x 27½"
7 169-722 1 Reducing Tee
8 169-724 1 Pipe Plug 1¼" NPT
9 113-006LL 1 Pipe 1" NPT x 9"
10 S30-059 1 Stay-Open Ball Valve Assembly
1" NPT
10.2 128-201 1 Handle
10.3 S27-278 1 1" Ball Valve with Jam Nut
10.31 110-214 1 Jam Nut only
10.4 153-489 1 Adapter
10.5 124-048 1 Washer, Friction
11 113-006LK 1 Pipe 1" NPT x 12"
12 169-847 1 90° Elbow 1" NPT
13 151-001 2 Curtain Hook
14 S24-188 1 Showerhead Assembly
15 128-156A 1 Pull Rod - 24" Long
16 269-915 1 Grip Pad (not shown)
17 169-025 2 Elbow ½" NPT
18 169-726 1 Union ½" Female NPT
19 113-006QX 1 Pipe 1¼" NPT x 7³⁄₃₃"
20 113-006LQ 3 Pipe 1/2" NPT x 3½"
21 S30-070 1 ½" Valve/Handle Prepack
Item Part No. Qty. Description
21.1 S27-282 1 ½" Ball Valve with Jam Nut
21.11 110-215 1 Jam Nut only
21.2 S08-336 1 Handle Assembly
21.3 142-002DA 1 Lockwasher
21.4 153-372R 1 Adapter
22 169-764 1 90° Pipe Elbow 1¼" NPT
23 113-006LE 1 Pipe Nipple 1¼" NPT x 3"
24 S90-094 1 Stainless Steel Eyewash Bowl
24.1 111-039 1 Inlet-Drain Fitting
24.2 124-028 1 Center Seal Gasket
24.3 187-053 1 Dust Cover Assembly
24.4 173-009 1 Cup Strainer
24.5 113-1150 1 Stem Pipe Assembly
25 S05-064D 1 EFW Assembly
25.1 S05-091P 1 Eye/face wash Yoke
25.2 S45-2453 1 Service Kit EFW - Black
Sprayheads
25.3 S53-063 2 Tethered Dust Cover
26 S45-572 1 Foot Treadle Kit
26.1 161-163 1 Nut
26.2 128-136 1 Valve handle
26.3 269-646 2 “S” Hook
26.4 134-009A 1 Stainless Steel Chain
26.5 181-014 1 Treadle
26.6 160-382 1 Screw
27 114-052 1 Safety Sign
28 204-421 1 Emergency Inspection Tag