Bradley Verge LVA Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1850 Rev. G: ECO 22-08-019
© 2022 Bradley
Page 1 of 13 6/1/2022
LVAD2
Verge®Wash Basin – LVA-Series with
Evero®Natural Quartz Material
Read the instructions in this manual before beginning installation. Save these instructions and refer to
them for inspection, maintenance, and troubleshooting information.
For questions regarding the operation, installation or maintenance of this product, visit bradleycorp.com or call 800.BRADLEY (800.272.3539).
Product warranties and parts information may also be found under “Resources” on our website at bradleycorp.com.
Table of Contents
Safety Information .............................................................2
Supplies Required .............................................................2
Components ......................................................................3
Dimensions........................................................................4
Structural Rough-In ...........................................................6
Plumbing and Electrical Rough-In.....................................7
Bracket Mounting...............................................................8
Drain Assembly .................................................................8
Basin Bracket for Access Panel Installation –
Evero Matte only................................................................9
Faucet and Soap Installation.............................................9
Bowl Mounting (to Bracket and Wall)...............................10
Strainer and Drain Cap....................................................11
Adjust Temperature with Water Running .........................11
Access Panel...................................................................12
Cleaning and Maintenance for Evero..............................13
Cleaning and Maintenance Instructions for
Stainless Steel.................................................................13

LVAD2 Installation
26/1/2022 Bradley • 215-1850 Rev. G: ECO 22-08-019
Safety Information
WARNING
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation. Electrical
power MUST remain off until installation is complete.
Installer's hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 pounds.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file this
manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances
is the responsibility of the installer. Product warranties may be found under “Products” on our Website at
www.bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 33.5" distance from the fixture rim to the
finished floor.
Supplies Required
• (6) ³⁄₈" fasteners and wall anchors for bowl and wall bracket (minimum pull-out rating of 1,000 lb)
•(4) ¼" fasteners and wall anchors for access panel brackets (minimum pull-out rating of 100 lb)
•½" hot/cold or tempered stub-out
•1½" NPT drain stub-out(s)
•OPTIONAL: (1) 110V GFCI protected electrical outlets for 100–120VAC plug-in transformers only
•Screen filter(s) as needed, if not included with faucet(s)
• Drill
•Crescent wrench
•Tape measure
•Phillips screw driver
•Flat head screw driver
• Level

Installation LVAD2
Bradley • 215-1850 Rev. G: ECO 22-08-019 6/1/2022 3
Components
LVAD2BO
Contact your Bradley
Representative for color options
Individual Rough-In Option
Chrome P-Trap (S29-094)
Plastic P-Trap (269-1697)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain
Adapter
Prepack
(S45-2480)
Access Panel
(186-1912)
Wall Bracket
(140-1128)
Drain Cap
(111-140)
Drain Cap Spacer
(269-2540)
Trough Strainer
(173-039)
Trough Strainer Screw
(160-353)
TMV Supply Connections
Hose Prepack
(S45-2731)
Hose Prepack
(S45-2730)
TMV Valve
(¹⁄₂" NPTM Outlet)
(S45-2701)
Tempered Supply Connections
Plastic
Hose
Plastic
Hose
Plastic Hose
Stainless
Steel
Hose
Supply Fittings
(Standard)
(S45-2511)
and
(S45-3000)
for Verge Faucets
S53-3100, S53-3300,
S53-3500, & S53-3700
Supply Fittings
(Standard)
(S45-2510)
and
(S45-2999)
for Verge Faucets
S53-3100, S53-3300,
S53-3500, & S53-3700
Access Panel Wall Bracket
(140-1172)
#10 Access Panel
Thumb Screw
(160-536)
Access Panel Security
Screw Option
(S45-2880)
Evero Matte
Basin Bracket
for Access Panel
(140-1256)

LVAD2 Installation
46/1/2022 Bradley • 215-1850 Rev. G: ECO 22-08-019
Dimensions (mm)
Top View (shown with Crestt Faucet and Soap)
Front View
14³⁄₈"
(366)
21"
(534)
5" (127) 6" (152) 6" (152)
57¹⁄₁₆" (1449)
15" (381) 15" (381)
50" (1270)
59¾" (1518)
20"
(508)
3¾" (95)
60" (1524)

Installation LVAD2
Bradley • 215-1850 Rev. G: ECO 22-08-019 6/1/2022 5
Dimensions – Side View (mm)
Side View with Faucet Side View with WashBar Duo
4¼" (107)
6¼"
(158)
7"
(178)
13½"
(343)
A
B
3¾" (95)
C
20"
(508)
21" (534)
20°
5" (126)
7½" (190)
ADA/TAS
Standard Height
ADA/TAS Juvenile Height
(Children 6-12 years)
CSA
Standard Height
Dim A 33½" (851) 30½" (775) 33½" (851)
Dim B 27" (686) 24" (610) 29²⁹⁄₃₂" (760)
Dim C 13½" (343) 10½" (267) 13½" (536)
Notes At least one basin must meet the dimensional requirements
and have proper reach, knee, and toe clearance
At least one basin must meet the dimensional requirements
and have proper reach, knee, and toe clearance

LVAD2 Installation
66/1/2022 Bradley • 215-1850 Rev. G: ECO 22-08-019
Mounting for Standard, ADA, and TAS height shown.
Structural Rough-In (mm)
Points A, B, and C require sufficient backing
compliant with local building codes.
A
A
B
B
C
L
CODE DESCRIPTION QTY.
AInstall (1) ³⁄₈" wall anchor with a minimum pull-out force of 1,000 lb per local codes at locations shown 2
B Provide structural backing compliant with local building codes. 2
C Install wall anchor with a minimum pull-out force of 100 lb per local codes at locations shown 4
Wall Bracket
RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE
33½" No Adjustment Standard Height, ADA, TAS, and CSA
30½" Subtract 3" Juvenile, ADA, and TAS
C
C
29⁵⁄₈"
(753)
Bottom
of
Bracket
33½"
(851)
14¼"
(362)
15³⁄₈"
(391)
27⁵⁄₈" (701) 27⁵⁄₈" (701)
24¹⁄₈" (612) 24¹⁄₈" (612)
¾"
(19)
36½" (927)
25" (635) 25" (635)
25¼"
(640)
Secure bracket to wall using min. (2) ³⁄₈" anchor bolts to
the left of C/L and min. (2) ³⁄₈" anchor bolts to the right of
C/L. The (2) anchor bolts to the right of C/L must be min.
16" apart from the anchor bolts to the left of C/L. When
mounting is complete, check to ensure the bracket is level.
See Step 1: Bracket Mounting for more information.
31½"
(800)
WARNING The bracket is not designed to support the
bowl. Wall bracket is a temporary support until
bowl is mounted at location "A". Ensure bowl
is completely seated in the wall bracket and
securely fastened to the wall at point A.

Installation LVAD2
Bradley • 215-1850 Rev. G: ECO 22-08-019 6/1/2022 7
(mm)
5⁹⁄₁₆"
(141)
24¹⁄₈"
(613)
23¾"
(603)
27¼"
(692)
24⁷⁄₈"
(633)
17½"
(444)
A
F F
F F
E
H C
1" (25)
Finished Floor
Approx. Soap
Battery Box
Location
Approx. Soap
Battery Box
Location
25" (635)19" (482)
19" (482)
8¹⁄₈"
(205)
3¹⁄₈"
(80) 7¾"
(198)
4½"
(114)
¼"
(5)
3¹⁄₈"
(80)
3¼" (83)
E
G GG G
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E110V GFI protected electrical outlet
WashBar Duo requires 120 VAC, GFCI outlet properly grounded 2
F #10 Anchors for Faucet Control Box Installation 4
G #10 Anchors for Soap Tank Installation 4
Plumbing and Electrical Rough-In
Mounting for Standard, ADA, and TAS height shown.
Verge™ deck-mounted soap dispenser and faucet rough-in is shown below.
For rough-in information on the LVAD2 Verge Wash Basin with WashBar Duo,
refer to the WashBar Duo WBD1 tech data.

LVAD2 Installation
86/1/2022 Bradley • 215-1850 Rev. G: ECO 22-08-019
Bracket Mounting
Typical installation is shown. It may be necessary to repair the wall
after mounting. The fixture may not cover all of the wall modifications.
1
Mounting height per structural rough-in drawing.
For ease of drain installation, lay the bowl on its back.
2Drain Assembly
C
L
16"
(406mm)
min.
O-Ring
Drain
Adapter
Packing
Washer
#10-24 x 1/2"
Screw
Assemble the remaining components as
shown and thread the four screws through
the drain adapter and into the basin inserts.
Ensure the screws compress the drain
adapter evenly onto the basin.
A
Install wall bracket to wall per
the Structural Rough-In drawing.
Check to ensure bracket is level.
(Example anchor locations are
shown below.)
A

Installation LVAD2
Bradley • 215-1850 Rev. G: ECO 22-08-019 6/1/2022 9
For ease of installation, leave the bowl laying on its back.
Follow the installation instructions shipped with the faucet and soap
units for assembly and installation information.
Basin Bracket for Access Panel Installation – Evero Matte only
Faucet and Soap Installation
3
4
Attach the supplied basin bracket for access
panel (140-1256) using the #10 fasteners
provided into the three threaded insert locations
on the bowl.
A
#10 Fasteners
Basin Bracket
for Access Panel
(Evero Matte only)
Evero Matte
Basin Bracket
for Access Panel
Locations

LVAD2 Installation
10 6/1/2022 Bradley • 215-1850 Rev. G: ECO 22-08-019
Bowl Mounting (to Bracket and Wall)
5
Position bowl above wall bracket.
Press firmly on the back of the bowl
to seat the bowl flange into the wall
bracket lip. Ensure bowl is level.
ASecure the bowl to the wall anchors
using fasteners per the structural
rough-in requirement (supplied by
installer).
B
WARNING Ensure bowl is completely seated in the wall bracket
and securely fastened to the wall at point A.
CAUTION Bracket is not intended to support the weight of bowl
for an extended period of time. Be sure to secure the
bowl to the wall using appropriate fasteners.
CAUTION Positioning bowl onto bracket may require two people.