Comeup CWL-200 User manual

Compact Winch
Model: CWL-200
PN: 372400 220V 371160 230V
372588 240V
Introduction
XFeature
Lifting capacity: 200 kg wire rope top layer
Lifting height: 45 m
Lifting speed: 11 – 16 m/min
Motor output: 1.5kw x 7.5A at 220-240V
Brake: Electromagnetic and mechanical ratchets
Control: Pendant switch powers the winch
XUnpacking
．Winch assembly 1pc
．Wire rope 5 mm x 46 m with weight hook CHW-0031 1pc
．Power lead 1.5 mm2
x 3C x 3 m and plug 1pc
．Pendant switch PB-317 w/cord 1.25 mm2
x 6C x 10 m 1pc
XRead this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
XInformation requesting or parts ordering
Please specify the followings information:
．Winch PN
．Serial number
．Part description
．Replacement part number
．Quantity for each part

Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be clear and dry.
XWire rope replacement
．Insert the wire rope into the hole of drum and fix it with a P. T. screw, then
press the "UP" button of switch for rotate the drum in the lifting direction.
．Wind the wire rope accurately around the drum, and an irregular winding
will cause the load to be swing, thus damaging the wire and reducing the
life of winch.
．When replacing, according to the following procedures.
*Pull out a R-dowel "D" from the round head pin "C".
*Pull out a round head pin "C” from hook body "A".
*Put a wire rope "B" into the hole of hook body "A", and insert a round
head pin "C" through wire rope and fixture hole of hook body "A".
*Insert a R-dower "D" into the hole of round head pin "C".
XWiring Diagram

Warning
．The winch is not intended to be used in any manner for the movement or
lifting of personnel.
．The lifting capacity shown is based on the top layer of rope on the drum.
．The rope winding on the drum shall remain 5 wraps from the drum.
Parts List
Item No. Description Part No. Qty
1 Gearbox rear cover kit 880546 1
2 Ratchet stopper kit 880547 2
3 2nd shaft 880548 1
4 3rd gear kit 880549 1
5 Brake kit 881516 1
6 Tie bar kit 880552 1
7 Tie bar kit A 880553 2
8 Wire rope 880554 1
9 Weight hook 880384 1
10 Gearbox support rack kit 880555 1
11 Output shaft kit 880556 1
12 Drum kit 881518 1
13 Motor coupling kit 881515 1
14 Motor support rack kit 880558 1
15 Torque shaft kit 881517 1
16 Motor housing kit 880561 1
17 Carbon brush holder kit 880472 1
18 Carbon brush 880563 2
Armature core, 220/230 V 880976
19 Armature core, 240 V 880977 1
20 Cooling cover 880564 1
Armature winding, 220/230 V 880518
21 Armature winding, 240 V 880519 1
22 Motor rear cover kit 880566 1
23 Terminal upper cover 880535 1
Control panel w/lead & 3 flat pins 881233
24 Control panel w/lead & 3 round pins 881232 1
25 Lower plate 880567 1
26 Remote control , PB-317 881601 1
27 P type hanger kit 881574 1

Winch Assembly