DEFA Solid 712800 User manual

1=8A
EV Charging Station
(EN) Installation manual

iii defa.com
Table of Contents
Safety information............................................................................................... 4
Main parts.......................................................................................................... 6
Installation planning............................................................................................ 7
Installation......................................................................................................... 8
Testing and verification........................................................................................ 15
Hand-over.......................................................................................................... 16
Technical specification......................................................................................... 17
Contact information ............................................................................................ 18

EN
defa.com 4
Safety information
Important! Read this document before installing the device. Failure to follow any of the
instructions or warnings can result in material damage or personal injury.
Important! The charging station must be installed, uninstalled or repaired by a licensed electrician
and the installation must be executed in accordance with national and local regulations.
Important! Make sure there is no power in the cable during the installation of the device.
Important! Disregard of, or actions contrary to the safety information and instructions contained
in the comprehensive manuals and printed on the device, may lead to electric shock, fire and/or
severe injury.
Special notes
DANGERSections marked with this symbol draw attention to electrical voltages that
represent a danger to life and limb. Actions contrary to these safety notices may lead to
severe or fatal injury. Actions contrary to these safety notices must not be carried out
under any circumstances.
WARNINGSections marked with this symbol draw attention to additional hazards that
may lead to damage to the cable itself or to other electrical devices. Actions marked
with this symbol must be carried out with special care.
i
NOTICESections marked with this symbol draw attention to additional important
information and special features that are necessary for the reliable operation of the
device. Actions marked with this symbol should be carried out as required.

EN
5 defa.com
Danger
Do not install if the outer shell
has been damaged. Do not install if the charging cable is defective or appears
cracked, broken or otherwise
damaged.
Do not carry out physical re-
pairs on the charging station.

EN
defa.com 6
Main parts
Charging station
1=8A
A
B
C
D
E
F
G
H
J
K
L
M
A. End cap
B. Charging unit
C. Display
D. Charging cable
E. Terminal block
F. Rotary switch
G. Wall bracket
H. Spirit level
Included
J. 2 x end cap
screws
K.1 x fixing screw
L. 4 x wall screws
M. 4 x wall plugs

EN
7 defa.com
Installation planning
Requirements for the cable
• Maximum size for the installation cable is 4 mm2.
• If a new cable is to be installed, apply only cable dimensions suitable for the entire circuit,
including the fuse.
• Note the maximum current (A) for the entire circuit. Consider possible additional electrical
devices connected to the same fuse, for later current settings in the charging station.
Requirements for the installation site
• Do not install the charging station in a spot where the maximum operating temperature is
exceeded. See chapter Technical specification for maximum temperature.
• Ideally, the installation site should be covered.
• The installation site must not be in an area subject to flooding, close to water, or in areas
used to store objects, or containers containing liquids.
• The installation site must not be in explosive atmosphere areas.
• The installation site must offer sufficient air circulation.
• Make sure there is 55 mm of free space above the bracket so the charging unit can slide
easily on and there is space for the top cover.
55mm
Tools needed
• Installation tools for correct wiring, including stripping tool.
• Cross recessed screwdriver for wall bracket screws.
• Torx tool size Tx 15 with space for safety pin.

EN
defa.com 8
Installation
DANGERMake sure there is no power in the cable during the installation.
WARNINGIf the charger or charging cable is damaged, the installation should
immediately be discontinued or, if the charger is already installed, it should be taken out
of operation. No additional use of the charger is permitted in this case.
1. Turn the power/fuse off.
2. Check that all parts and tools required for the installation are available.
3. Guide and fix the installation cable to the spot where the charging station will be installed.
– If necessary, find and reveal the cable inlet in the wall bracket. The cable can be
inserted from the top, left, right, or bottom. Make sure that the cable is long enough.
See image in step 6 below for details.
4. Place the wall bracket with a clearance of 55mm to any obstacles above the installation area.
5. Attach the wall bracket. Use the built-in spirit level to ensure that the wall bracket is installed
at a level angle. Use the four screws delivered with the product. The holes are made for
screws with Ø4.2mm.
6. Remove the jacket (from A to B) with a length of 140mm. Strip all single wires with 9-11mm.

EN
9 defa.com
Spirit level
A
B
Top Right Left Bottom
7. Place the cable in the groove that points the conductor toward the hole in the upper left
corner.
8. Slide the charging unit from the top, so that all the conductors fit into the cable entry in the
inner end piece. Make sure that the grooves at the top and bottom are firmly in place.

EN
defa.com 10
9. Attach the fixing screw to secure the charging unit to the wall bracket.

EN
11 defa.com
1=
8A
Fixing screw
Cable entry
Rotary switch
10. Set the maximum current rating for the charging station by turning the rotary switch to the
correct position. Follow the table next to the rotary switch on the charging unit or in the
image below.
11. Insert the conductors L, N and PE (earth) into the terminal block (see image below), and
check that they are all firmly attached.
i
NOTICEIf the PE conductor is not isolated, add an insulation tube or electrical tape in
the exposed area.
12. Place the cable in the position shown in the image below.

EN
defa.com 12
13. Note the settings from the rotary switch by marking the cell with an X below the relevant
fields in the table found in the user manual, see chapter Set the required charging level.
14. Attach a sticker with the set rating - max charging power - on the underside of the vehicle
plug (over the existing rating label).

EN
13 defa.com
18 A 6 C18 A
4,1 kW
16 A 5 C16 A
3,7 kW
15 A 4 C15 A
3,5 kW
13 A 3 C13 A
3,0 kW
10 A 2 C10 A
2,3 kW
8 A 1 C8 A
1,8 kW
6 A 0 C6 A
1,4 kW
20 A 7 C
15. Attach outer end cap with two screws on top of the charging unit to close the installation
area.

EN
defa.com 14
16. Coil charging cable around the charging unit.
17. Turn the power/fuse on.

EN
15 defa.com
Testing and verification
Make sure the charging station is ready to use by checking which signals are displayed on the
display before, during, and after charging the vehicle. See chapter Charge the vehicle in the user
manual.
Display view
B
A
C
D
A. Power Input Indication
B. Select Button
C. Charger Status Indication
D. Vehicle Connection Indication

EN
defa.com 16
Hand-over
Follow these instructions before handing over the device to the user:
• Show which rating the installation has.
• Demonstrate how to use the device.
• Inform how to find further information about their device
• Inform what to do if they experience issues with their device.
• Hand over the user manual.

EN
17 defa.com
Technical specification
Item number 712800
Rated voltage 230 VAC (1-phase, 50-60Hz)
Rated current 6A - 20A
Charger type Mode 3
Connection to vehicle Type 2
RCD 30 mA AC & 6mA DC
GRID type TN- and IT-power grid
Overheat protection Internal sensor
Operating temperature -40 °C to +50 °C
Storage temperature -50 °C to +85 °C
Size (L x W x T) 312 x 85 x 70 mm
Material charging unit Aluminum
IK rating IK 08
IP rating IP 44
Weight 2,3 kg
Certification CE, IEC61851, IEC62955
Recycling EE-waste

EN
defa.com 18
Contact information
If you have any questions, contact your local vendor, visit defa.com or call DEFA support:
• Phone (Norway/International): [phone]
• Phone (Sweden/International): [phone]
• Phone (Finland): [phone]
If you have any feedback on how the system or support can be improved, feel free to give us your
input at [email protected]