Elo TouchSystems 15A2 for wireless card User manual

Reconnect the power adapter and
power on the touchcomputer.
Insert the software CD into the
DVD drive (or USB DVD drive) and
follow the on-screen instructions to
complete the Wireless Card software
installation.
Installing the Wireless card for the 17A2/15A2
Revision B
P/N E247787
2008 Tyco Electronics.
North America
Elo TouchSystems
301 Constitution Drive,
Menlo Park, CA 94025
www.elotouch.com
Europe
Tel [phone]
Fax [phone]
[email protected]
Asia-Pacific
Tel [phone]
Fax [phone]
www.tps.co.jp
Latin America
Tel [phone]
Fax [phone]
www.elotouch.com.ar
Elo Technical Support
:
www.elotouch.com/go/websupport
www.elotouch.com/go/contactsupport
Online self-help
Technical Support contacts in your region:
15A2
17A2
78
56
34
12
Turn off power to the touchcomputer
and unplug the power adapter from
the unit.
Align the pins of the Wireless card
with the connector at an angle and
push it in until the pins are in place.
Then push the Wireless card down
until it clicks. If the two side locks
on the connector do not click into
place, remove the card and repeat
the installation until the card clicks
securely in place.
Unscrew the security screw and
remove the MiniPCI cover.
If there is an installed DVD drive,
remove the two screws attaching
the DVD drive flap and remove
the flap. Then pull on the DVD
drive so it slides out of the
touchcomputer.
Unscrew the shielding that is
connected by four screws and
remove it.
Take the cable labeled “Wireless
card” and connect it to the connector
labeled “MAIN” on the Wireless card.
Reinstall the MiniPCI cover with the
security screw and reinstall the
shielding with the four screws.
Replace the back cover insert.
If the DVD drive flap was previously
removed, reinstall the flap with the
two screws and reinsert the DVD
drive, verifying that the drive locks
securely in place.
Note: This wireless card is intended to be used only with a 17A2 or
15A2 touchcomputer. Elo Touchsystems is not liable for any damages
incurred while using this device in any non-specified manner.
9 10 11
9
6
35
12
Turn off power to the touchcomputer
and unplug the power adapter from
the unit.
Align the pins of the Wireless card
with the connector at an angle and
push it in until the pins are in place.
Then push the Wireless card down
until it clicks. If the two side locks
on the connector do not click into
place, remove the card and repeat
the installation until the card clicks
securely in place.
Unscrew the shielding that is
connected by six screws and
remove it.
Take the cable labeled “Wireless
card” and connect it to the connector
labeled “MAIN” on the Wireless card.
Reinstall the shielding with the six
screws.
Replace the back cover insert.
For current Elo news, product updates and announcements, register to receive our TouchMonitor newsletter
at www.elotouch.com/go/news
Reconnect the power adapter and
power on the touchcomputer.
Insert the software CD into the
DVD drive (or USB DVD drive) and
follow the on-screen instructions to
complete the Wireless Card software
installation.
821107901201
DVD/ CD
DVD/ CD
Carefully place the touchcomputer
facedown on a soft, flat surface.
Turn touchcomputer upside down
and take off the back cover insert.
Carefully place the touchcomputer
facedown on a soft, flat surface.
Turn touchcomputer upside down
and take off the back cover insert.
●
Note: Always handle the component by its edges.
●
Installer must be electrically grounded while performing installation steps.
(B)
(A)
4
Remove the existing hard drive. Replace the hard drive into the hard
drive space. Push the hard drive
up until it snap locks into the
connector.
(B)
(A)
7810