Elo TouchSystems E-Series Operating and safety instructions

Elo Touch Solutions
E-Series RAM removal/replacement
TS02052016 RevA
Elo Touch Technical Services

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 2 of 10
Copyright © 2016 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, including, but not limited to, electronic,
magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its affiliates
(collectively "Elo") makes no representations or warranties with respect to the contents herein, and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of Elo to
notify any person of such revisions or changes.
Trademark Acknowledgments
AccuTouch, CarrollTouch, Elo, Elo (logo), Elo Touch, Elo Touch Solutions, Elo TouchSystems, IntelliTouch, iTouch,
SecureTouch, TouchTools and VuPoint are trademarks of Elo and its affiliates. Windows is a trademark of Microsoft
Corporation. ADATA is a trademark of the ADATA company.

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 3 of 10
Table of Contents
Introduction ........................................................................................... 4
Tools Needed.......................................................................................... 5
Procedure ............................................................................................... 6

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 4 of 10
About This Manual
This document guides the user through removing/replacing the RAM on the Elo E-SeriesAIO
touchcomputer.
The intended audience of this document includes: IT engineers, system engineers, electrical
engineers, and end-users.
If after reading through this guide, you still have questions or need help getting your system up and
running, please contact an Elo Touch Solutions Technical Representative. www.elotouch.com

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 5 of 10
Tools Needed
The following hardware is needed:
Hardware:
Flat protective surface
Elo E-Series AIO Touchcomputer
Small Philipps Screwdriver
Replacement RAM module

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 6 of 10
Procedure
1. With E-Series lying back side down on flat protective surface, pull up on two side tabs to
remove front plastic cover. (If cover is secured with a screw, use the Philipps screwdriver to
remove it).
2. Using fingers or the Philipps screwdriver, remove the large black screw that holds the front
metal plate.

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 7 of 10
3. Grasp the HardDrive and push in upward direction to release the front metal plate of unit.
4. Lift front metal plate away from unit to gain access to the RAM module.

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 8 of 10
5. Using fingers push the RAM retainer clips outward to release the RAM module. The RAM will
spring upward when fully released.

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 9 of 10
6. Lift RAM module up out of unit.

© 2016 Elo Touch Solutions, Inc. All rights reserved.
Removing/Replacing RAM module on the Elo E-Series AIO
TS02052016 Rev A, Page 10 of 10
7. Replace or add RAM memory module with compatible RAM.
NOTE: RAM must be DDR3L (low voltage). Standard DDR3 will not work in this unit, it must be
low voltage. Maximum memory using 1 available slot; replacement for single, pre-installed
memory module. Replaceable up to 4GB maximum, SODIMM DDR3L-1333.
Check out our website
www.elotouch.com
Get the latest...
Product Information
Specifications
Upcoming events
Press releases
Software drivers
Getting in Touch with Us
To find out more about the extensive range of Elo touch solutions, visit our website at
www.elotouch.com, or simply call the office nearest you:
North America
Elo Touch Solutions
1033 McCarthy Blvd
Milpitas, CA 95035
Tel 800-ELO-TOUCH
Tel + 1 408 597 8000
Fax [phone]
[e-mail]
Europe
Tel [phone]
Fax [phone]
[e-mail]
Asia-Pacific
Tel [phone]
Fax [phone]
www.elotouch.com.cn
Latin America
Tel [phone]
Fax [phone]
www.elotouch.com