Elo TouchSystems 1528L User manual

USER MANUAL
Elo Touch Solutions
1528L Touchmonitors
SW2000095 Rev A

UserManual:1528L
SW200095RevA,Page2of39
Copyright 2012 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, including, but not limited to, electronic,
magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any implied
warranties of merchantability or fitness for a particular purpose. Elo Touch Solutions, Inc. reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of Elo Touch
Solutions, Inc. to notify any person of such revisions or changes.
Trademark Acknowledgments
AccuTouch, CarrollTouch, Elo Touch Solutions, Elo TouchSystems, IntelliTouch, SecureTouch, and TouchTools are
trademarks. Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies.

UserManual:1528L
SW200095RevA,Page3of39
Warnings and Cautions
Warning
Danger — Explosion hazard. Do not use in the presence of flammable anesthetics.
To prevent fire or shock hazards, do not immerse the unit in water or expose it to rain or
moisture.
Do not use the unit with an extension cord receptacle or other outlets unless the prongs
of the power cord can be fully inserted.
RISK OF ELECTRICAL SHOCK — DO NOT OPEN. To reduce the risk of electrical
shock, DO NOT remove the back of the equipment or open the enclosure. No user-
serviceable parts are inside. Refer servicing to qualified field service engineers only.
Uninsulated voltage within the unit may have sufficient magnitude to cause electrical
shock. Avoid contact with any part inside the unit.
Caution
Before connecting the cables to your Elo TouchSystems touchmonitor, make sure all
components are powered OFF.
The use of ACCESSORY equipment not complying with the equivalent safety
requirements of this equipment may lead to a reduced safety of the resulting system.
Consideration relating to the choices of accessory equipment should include:
Use of accessory in the patient vicinity.
Evidence that the safety certification of the accessory has been performed in
accordance to the appropriate IEC 60601-1 and/or IEC 60601-1-1 harmonized national
standard.
For continued safety —
- This unit only complies to the above standards if used with a medical grade power
cord.
- A medical grade power adaptor, such as the one specified, is required for use in a
medical application.

UserManual:1528L
SW200095RevA,Page4of39
CAUTION-Life Support
Care must be taken when this touchmonitor is a critical component of a Life support
system or device. In case of failure of this touchmonitor, appropriate redundant
systems should be incorporated into the system or device to prevent injury to the user
or patient.
The following should be an integral part of the safety design of a Life support system or
device using this touchmonitor for a critical function.
An Alternate interface or fail-safe must be available should the touchscreen fail to
operate.
The touchscreen interface must not be the only means of control of a critical
function.
An Alternate video monitor should be incorporated into the safety design if used
to monitor a critical function.
The internal speakers of this touchmonitor must not be the sole method of
warning of a critical function.
Critical functions are:
1. Life support devices or systems are devices or systems which, (a) are intended
for surgical implant into the body, or (b) support or sustain life, or (c) whose
failure to perform when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result in significant injury
to the user.
2. A critical component is any component of a life support device or system whose
failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.

UserManual:1528L
SW200095RevA,Page5of39
Classification
With respect to electrical shock, fire in accordance with ANSI/AAMI ES60601-1 and
CAN/CSA C22.2 No. 60601-1-08
This monitor is a CLASS 1 (GROUNDED) DEVICE.
This monitor is classified NO APPLIED PARTS EQUIPMENT.
Protection against harmful ingress of water:
INGRESS PROTECTION (IPX1)
This monitor shall be classified as ORDINARY EQUIPMENT, not intended or evaluated
for use in the presence of flammable anesthetic mixture with air, oxygen, or nitrous
oxide.
Mode of Operation: CONTINUOUS OPERATION.
Environmental conditions for transport and storage
Temp. Operating 0°C to 40°C
Storage -20°C to +60°C
Humidity (non-
condensing)
Operating 20% to 80%
Storage 5% to 90%
Altitude
Operating
0 to + 3658m [12000 ft.]. Equiv. to 14.7 to 10.1 psia.
Storage 0 to + 12 192m [40 000 ft]. Equiv. to 14.7 to 4.4 psia.
For full Product Specifications refer to Chapter 7.

UserManual:1528L
SW200095RevA,Page6of39
Explaination of Symbols
Symbol Description
UL Classification means that UL has tested and evaluated samples
of the product with respect to certain properties of the product.
(look on page 9 )
For those EU Directives that permit it, the CE mark indicates product
compliance with standards indicated in the "Certificate of
Conformance" which accompanies the product packing information.
The Directive may or may not require verification by a Notified Body.
The LVD, EMC and MDD Directives permit products to indicate
conformity by the CE mark. MDD products may also require a
Notified Body mark.
Indicates tested to comply with FCC standards.
Indicates compliance with the European Community WEEE directive
2002/96/EC. Dispose of according to federal, state or local
regulations.
This symbol alerts the user to consult accompanying documents for
important information concerning the operation and maintenance of
this unit, which should be read carefully to avoid problems.
EMC Guidance
Guidance and manufacturer’s declaration – electromagnetic emissions
The 1528L is intended for use in the electromagnetic environment specified below. The customer or the user of the
1528L should assure that it is used in such an environment.
Emissions test Compliance Electromagnetic environment – guidance
RF emissions
CISPR 11
Group 1 The 1528L uses RF energy only for its internal function. Therefore, its RF
emissions are very low and are not likely to cause any interference in nearby
electronic equipment.
RF emissions Class B
Harmonic
emissions
IEC61000-3-2
Not applicable
Voltage
fluctuations/
flicker emissions
IEC61000-3-3
Complies

UserManual:1528L
SW200095RevA,Page7of39
Guidance and manufacturer’s declaration – electromagnetic immunity
The 1528L is intended for use in the electromagnetic environment specified below. The customer or the user of the
1528L should assure that it is used in such an environment.
Immunity test IEC60601
test level Compliance level Electromagnetic environment –
guidance
Electrostatic discharge
(ESD)
IEC61000-4-2
±6 kV Contact
±8 kV air
±6 kV Contact
±8 kV air
Floors should be wood, concrete or
ceramic tile. If floors are covered with
synthetic material the relative humidity
should be at least 30 %
Electrical fast
transient/burst
IEC61000-4-4
±2 kV for power supply
lines
±1 kV for input/output
lines
±2 kV for power supply
lines
±1 kV for input/output
lines
Main power quality should be that of a
typical commercial or hospital
environment.
Surge
IEC6100-4-5
±1 kV differential mode
±2 kV common mode
±1 kV differential mode
±2 kV common mode
Main power quality should be that of a
typical commercial or hospital
environment.
Voltage dips, short
interruptions and voltage
variations on the power
supply input lines
IEC61000-4-11
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
<5 % UT
(>95 % dip in UT)
for 5 sec
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
<5 % UT
(>95 % dip in UT)
for 5 sec
Main power quality should be that of a
typical commercial or hospital
environment. If the user of the 1528L
requires continued operation during
power mains interruptions, it is
recommended that the 1528L be
powered from an uninterruptible power
supply or a battery.
Power frequency
(50/60 Hz)
Magnetic field
IEC61000-4-8
3 A/m 3 A/m, 30 A/m Power frequency magnetic fields
should be at levels characteristic of a
typical location in a typical commercial
or hospital environment.
NOTE UTis the ac. mains voltage prior to application of the test level.

UserManual:1528L
SW200095RevA,Page8of39
Guidance and manufacture’s declaration – electromagnetic immunity
The 1528L is intended for use in the electromagnetic environment specified below. The customer or the user of the
1528L should assure that it is used in such an environment.
Immunity Test IEC60601 test level Compliance
level
Electromagnetic environment – guidance
Conducted RF
IEC61000-4-6
Radiated RF
IEC61000-4-3
3 Vrms
150 kHz to 80 MHz
10 Vrms
80 MHz to 2.5 GHz
3 V
3 V/m
Portable and mobile RF communications equipment
should be used no closer to any part of the
[EQUIPMENT or SYSTEM], including cables, than the
recommended separation distance calculated from the
equation applicable to the frequency of the transmitter.
Recommended separation distance
__
d= 1,2 √P
__
d= 1,2 √P80 MHz to 800 MHz
__
d= 2,3 √P800 MHz to 2,5 GHz
where Pis the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in meters (m).b
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,cshould
be less than the compliance level in each frequency
range.d
Interference may occur in the vicinity of equipment
marked with the following symbol:
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
aThe ISM (industrial, scientific, and medical) bands between 150 kHz and 80 MHz are 6,765 MHz to 6,795 MHz;
13,553 MHz to 13,567 MHz; 26,957 MHz to 27,283 MHz; and 40,66 MHz to 40,70 MHz.
bThe compliance levels in the ISM frequency bands between 150 kHz and 80 MHz and the frequency range 80
MHz to 2,5 GHz are intended to decrease the likelihood that mobile/portable communications equipment could
cause interference if it is inadvertently brought into patient areas. For this reason, an additional factor of 10/3 is
used in calculating the recommended separation distance for transmitters in these frequency ranges.
cField strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast cannot be predicted theoretically with accuracy. To
assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the 1528L is used exceeds the applicable RF
compliance level above, the 1528L should be observed to verify normal operation. If abnormal performance is
observed, additional measures may be necessary, such as reorienting or relocating the [EQUIPMENT or
SYSTEM].
dOver the frequency range 150 kHz to 80 MHz, field strengths should be less than [V1] V/m.

UserManual:1528L
SW200095RevA,Page9of39
Recommended separation distances between
Portable and mobile RF communications equipment and the 1528L
The 1528L is intended for use in which radiated RF disturbances are controlled. The customer or the user of the 1528L can help
prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications
equipment (transmitters) and the 1528L as recommended below, according to the maximum output power of the communications
equipment.
Separation distance according to frequency of transmitter
M
Rated maximum output power of
transmitter
W 150 kHz to 80 MHz
__
d= 1,2 √P
80 MHz to 800 MHz
__
d= 1,2 √P
800 MHz to 2,5 GHz
__
d= 2,3 √P
0,01 0,12 0,12 0,23
0.1 0,38 0,38 0.73
1 1,2 1,2 2,3
10 3,8 3,8 7,3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can
be estimated using the equation applicable to frequency of the transmitter, where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection
from structures, objects and people.
This device complies with all applicable electromagnetic emission and immunity standards for medical
device equipment. This device is designed to not cause harmful interference, and to accept any
interference received, including interference that may cause undesired operation. The performance of this
device is limited to the emission and immunity standards that have been applied. Other devices which are
not designed to withstand emission levels as specified in the medical device standards may be susceptible
to interference from this device. Subjecting the device to conditions beyond the rated performance
capabilities may result in emissions in excess of the standard. If it is determined that this device produces
electromagnetic or other interference it must be disconnected from power until the cause of the problem
has been determined and resolved. If it is determined that this device is functioning improperly due to
electromagnetic and other interference it must be disconnected from power until the cause of the problem
has been determined and resolved.

UserManual:1528L
SW200095RevA,Page10of39
Table of Contents
Chapter 1: Introduction.....................................................11
Chapter 1: Introduction.....................................................11
Chapter 2: Installation and Setup ....................................12
Chapter 3: Operation.........................................................19
Chapter 4: Troubleshooting .............................................23
Chapter 5: Native Resolution ...........................................24
Chapter 6: Touchmonitor Safety......................................25
Chapter 7: Technical Specifications................................27
Chapter 8: Contact Elo Touch Solutions ........................35
Chapter 9: Regulatory Information..................................36
Chapter 10: Warranty ........................................................38