EMKO Trans-midiAUTO.MPU.232... User manual

Introduction Brochure. ENG TRANS-MIDIAUTO 01 V10 10/20
TRANS-MIDIAUTO
AUTOMATIC START UNIT
1.2 Warranty
EMKO Elektronik warrants that the equipment delivered is free from defects in material and workmanship.
This warranty is provided for a period of two years. The warranty period starts from the delivery date. This
warranty is in force if duty and responsibilities which are determined in warranty document and instruction
manual performs by the customer completely.
1.3 Maintenance
Repairs should only be performed by trained and specialized personnel. Cut power to the device before
accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of these
solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl alcohol or
water to clean the external plastic case.
1. Introduction
1.1 General Specifications
The unit provides automatic start and stop the engine and protect the generator system. Both
automatic and manual control is possible. A test mode is also available which allows the generator to
be run for checking the generator system.
The unit monitors J1939 ECU messages and provides remote start/stop control via J1939 protocol
(supported ECUs: Volvo EMS2, Volvo EDC4, Perkins, Scania S6 and standard messages).
The unit monitors generator operation and gives warning of any faults that are detected.
The configurable input-3 can be used as the water level sensing input.
The unit calculates engine RPM from Magnetic Pickup sensor input (Trans-MidiAUTO.MPU devices
only) and/or generator voltage signal. At Trans-MidiAUTO.CAN devices, unit gets engine RPM
information from J1939 ECU.

Ýçindekiler
A visual inspection of this product for possible damage occured during shipment is
recommended before installation. It is your responsibility to ensure that qualified mechanical
and electrical technicians install this product.
If there is danger of serious accident resulting from a failure or defect in this unit , power off
the system and seperate the electrical connection of the device from the system.
Keep the power off until all of the wiring is completed so that electric shock and trouble with
the unit can be prevented.
Before beginning installation of this product, please read the instruction
manual and warnings below carefully.
2. Installation
Ýçindekiler
2.1 Unit Configuration
Ýçindekiler
2.2 Panel Mounting
The unit is designed for panel mounting. Fixing is by two screw fixings.
Insert the unit in the panel cut-out from the front.
Insert the fixings in the slotted at the corners of the unit and tighten the fixing screws to secure
the unit against the panel.
1-
2-
During the equipment is putted in hole on the metal panel while mechanical
installation some metal burrs can cause injury on hands, you must be careful.
Figure 2.1 Front View Figure 2.2 Panel Cut-Out
The unit can be programmed using the buttons and LCD display on the front panel or PC
Software.
2
120mm
94mm
111mm
158mm
!
!

2.3 Electrical Connection
3
TRANS-MidiAUTO three phase connections schematic
1- Connect the unit as shown in the appropriate diagram. Be sure to connect the battery
supply the right way round and battery negative should be grounded.
2- The CAN interface requires that a 120 Ohms terminator is fitted to each end of the
communications link. This termination resistor is fitted internally into the unit. So it is not
required externally. The screen is grounded at one end ONLY.
Screened cable must be used for connecting the Magnetic Pickup, ensuring that the
screen is grounded at one end ONLY.
i
3-
4- Current transformers secondary should be grounded. The CT of 5VA s recommended.
!
37
Level Sender or
Configurable Analog Input
Temperature Sender
Oil Sender
36 35 18
19
BATTERY -
BATTERY +
38
Sender Common
21 20
16 17
15
22
RX TX
RS-232
J1939 ECUs
34
BATTERY -
33 32 31 30 29
High Temperature or
Configurable Input-5
Low Oil Pressure or
Configurable Input-4
Remote Start or
Configurable Input-2
To Engine
Earth
GND
FUSE-4
*
*IT CAN BE USED
AS A DIGITAL INPUT
BY SELECTING
FROM THE PROGRAM
PARAMETERS
*
*
1
Configurable Output-4
26 25 24 23
Configurable Output-3
TRANSISTOR OUTPUTS MAX. 1 A
BATTERY +
SCR +
MPU
Emergency Stop or
Configurable Input-1
23
8A
145
L1
GENERATOR
L2
L3
N
TO
LOAD
G
11 12 13 14
Generator
Contactor
Relay
FUSE-1
FUSE-2
FUSE-3
4
!
!
3
!
2
!
Fuel Or Output-1Configurable
Crank Or Output-2Configurable
D+(W.L.)
Charge Alt.
Max. 300VV
FUSE-1 8A. T
FUSE-2, FUSE-3
FUSE-4 6A. T
2A. T
28 27
Configurable Output-5
Configurable Output-6
Water Level or
Configurable Input-3
H(+)
L(-)
-
SCR

4
3. Changing And Saving Parameters Values
Enter password with cursor
(Right, Left, )
.
Up and Down
buttons
Press the Up or Down
buttons to select the main
parameter group you wish
to view/change.
Parameter can be changed
with Up and Down buttons.
Press Enter button to
access to all parameters in
currently parameter page.
GENERATOR
V12: 380V V1: 220V
V23: 380V V2: 220V
V31: 380V V3: 220V
On load
ü
ü
Operation Screen
Press the Up or
Down buttons to
select the section
you wish to
view/change.
Press the
Enter
button.
Press the Enter button to confirm
password. If the password is
incorrect, the unit will drop out of
program mode.
Note1: If Enter button is pressed
and the technician password is
zero, Password screen will be
ignored.
Press Enter button to access to
all parameters page in current
main parameter group.
Press Enter button
to confirm the changed
value.
Program
Language
Event Log
PROGRAM
Operator setting
Technician setting
Factory adjustment
TECHNICIAN SETTING
Password
0162
TECHNICIAN SETTING
Password
0000
TECHNICIAN SETTING
System
Generator
Engine
Inputs
TECHNICIAN SETTING
System
Generator
Engine
Inputs
GENERATOR
Volt level
Frequency level
Current level & act.
Power level
GENERATOR VOLT LEVEL
Under volt shutdown
320 Vac
GENERATOR VOLT LEVEL
volt reset
Over volt shutdown
Under volt shutdown
Under volt prealarm
Under
Press the Enter
button to view
parameter value.
GENERATOR VOLT LEVEL
Under volt shutdown
325 Vac
GENERATOR VOLT LEVEL
volt reset
Over volt shutdown
Under volt shutdown
Under volt prealarm
Under
Operation
Screen
To exit from
programming mode any
time, press Stop/Reset
button for 2 seconds.
ü
PROGRAM
Operator setting
Technician setting
Factory adjustment
ü
ü
ü ü
ü ü
ü ü
ü ü
GENERATOR
V12: 380V V1: 220V
V23: 380V V2: 220V
V31: 380V V3: 220V
On load
Press Enter button to
access the menu options.
Press Enter button to
access the wished
menu item.
GENERATOR
Volt level
Frequency level
Current level & act.
Power level
When the Stop/Reset button
is pressed any time, previous
page can be accessed.

5
Note: dis = disable
4.1 Operator Parameters
4. Parameters
600
60(dis)
60
60
600
600
600
VV
VV
VV
VV
60(dis)
Min Default Max
Generator Under Voltage Shutdown
Generator Under Voltage Pre-Alarm
Generator Under Voltage Pre-Alarm Reset
Generator Over Voltage Shutdown
Generator Over Voltage Pre-Alarm
320
dis
350
440
60(dis) 600
60 600
dis
400
Generator Over Voltage Pre-Alarm Reset
VV
VV
Under volt shutdown
Under volt prealarm
Under volt reset
Over volt shutdown
Over volt prealarm
Over volt reset
Unit
Shutdown delay time
Generator Voltage Shutdown Delay Time
GENERATOR VOLT LEVEL ( )Generator-> levelVolt
0.0 10.0 1.0 Sec
75.0
30.0(dis)
75.0
75.0
Hz
30.0(dis)
Min Default Max
Generator Under Frequency Pre-Alarm
Generator Under Frequency Pre-Alarm Reset
Generator Over Frequency Shutdown
Generator Over Frequency Pre-Alarm
Generator Over Frequency Pre-Alarm Reset
Dis
46.0
58.0
Dis
54.0
Generator Frequency Shutdown Delay Time
Hz
Hz
Hz
Hz
30.0
30.0(dis)
30.0
75.0
75.0
Under freq prealarm
Under freq reset
Over freq shutdown
Over freq prealarm
Over freq reset
Shutdown delay time
Unit
GENERATOR LEVEL ( )FREQ Generator-> levelFrequency
75.0
75.0
Hz
30.0
Nominal Alternator Frequency 50.0
43.0 Hz
Nominal frequency
Under freq shutdown Generator Under Frequency Shutdown 30.0(dis)
0.0 10.0 1.0 Sec
4.1.1 Generator
9999
9999
9999
9999
9999
9999
kVA
kVA
kVA
kVA
0
0(dis)
0
0
0(dis)
0
Min Default Max
Generator Under SetPower
Generator Under Pre-AlarmPower
Generator Under Pre-Alarm ResetPower
Generator Over SetPower
Generator Over Pre-AlarmPower
0
5
Generator Over Pre-Alarm ResetPower
kVA
kVA
Under setpower
Under prealarmpower
Under resetpower
Over setpower
Over prealarmpower
Over resetpower
Unit
Reverse power set
Reverse Power Set
GEN LEVEL ( )POWER Generator->Power level
-9999 0 0 kW
dis
0
0
dis
Min Default Max
Generator Under Current Pre-Alarm Reset
Generator Over Current IDMT Alarm
Generator Over Current Set
Generator Over Current Pre-Alarm
Generator Over Current Pre-Alarm Reset
Under cur. reset
Over cur. IDMT alarm
Over cur. set
Over cur. prealarm
Over cur. reset
Unit
GENERATOR ( )CUR LEVEL Generator->Current level
Generator Under Current Set
Under cur. set
Under cur. prealarm Generator Under Current Pre-Alarm
0 9999 9980 AV
0
0(dis)
0
0
0(dis)
9999
9999
9999
9999
9999
1
dis
5
DISBL
9999
Dis
AV
AV
AV
AV
AV
ENABL/DISBL

6
4.2 Technician Parameters
4.2.1 System
Min Default Max
Current Transformer Ratio
Voltage Transformer Ratio
Select AC system;
Generator Phase Sequence (dis, L123 or L321)
Generator kVA rating set
Power unit
kVA kW kVAr point position;, ,
CT ratio
PT ratio
Type of AC system
Phase sequence
Generator kVA rating
Power unit
kVA,kW,kVAr point
Unit
SYSTEM NETWORK ( )System->Network
3
9999
100
kVA
0
0
1
1
150
kVA
1
DISBL
0- 1 Phase 2 Wire
1- 3 Phase 4 Wire
2- 2 Phase 3 Wire L1-L2
3- 2 Phase 3 Wire L1-L3
DISBL, L123, L321
99991 20
kVA/kW
30 0
0-> 0
1-> 0.0
2-> 0.00
3-> 0.000
Min Default Unit
LCD DISPLAY ( )System->LCD display Max
Language Selection
Contrast Setting
Auto Backlight Off
ENGLISH/TURKISH
5
4 9
Contrast
Auto backlight off
Language
Auto Scroll Time
Auto Scroll Number
Scroll Time For Error Messages
0
0 (dis) 250 Sec
5
18
2
1 250
Auto scroll number*1
Err. mesg scroll time
Auto scroll time
Sec
1
ENGLISH
ENA DISBLBL/ DISBL
Min Default Unit
BREAKERS ( )System->Breakers
Max
Hardware Breaker Selection
Gen Close Breaker Contact Type
Gen Close Breaker Relay Type
Gen Close Timer
1
Gen Open Breaker Relay Type
0(dis) 3
Gen Open Timer
NO / NC 0
NOR / PULS
5
1 250
0
Sec
0
NOR / PULS
1 250 5
0.0
0.0
0
10.0
10.0
250 2
Breaker Close Pulse Time
Breaker Open Pulse Time
Transfer Time
Spring Loading Time
Retry Number
Gen.brk.cls.contact
Gen.brk.cls.relay
Gen.brk.cls.time
Gen.brk.open relay
Gen.brk.open time
Type of Breaker
Break.close puls.time
Transfer time
Spring loading time
Retry number
Break.open pulse time
Sec
0.5
0.5
Sec
Sec
Sec
Sec
3
5
1 250
1 250
Note: = Max. value of this parameter is equal to 24 at Trans-MidiAUTO.CAN devices
dis = disable
*1
NOR / PULS : Normal / Pulse
NO / NC : Normally Open / Normally Close

7
Min DefaultDATE & TIME SET ( )System->Date & time set Max
Year
Month
0 99
112
Date 131
Day of week 17
Hour 023
Minute 059
Second 059
Year
Month
Day
Week
Hour
Minute
Second
Unit
Min Default Unit
PASSWORD SETTINGS ( )System->Password settings Max
Operator Password
Technician Password
0
0 9999
09999 0
Operator password
Technician password
Min Default Unit
DEFAULT SETTINGS ( )System->Default settings Max
Save setting to default
Reset default sets
Save setting to def.
Reset default sets
YES / NO NO
Reset factory sets
Reset factory sets
YES / NO NO
YES / NO NO
Min Default Unit
COMMUNICATION ( )System->Communication Max
Slave Address 1
1 247
05 3
Baud Rate: 0 - 1200 baud
1 - 2400 baud
2 - 4800 baud
3 - 9600 baud
4 - 19200 baud
5 - 38400 baud
Datalog Period
Timeout
Local/Remote selection
Stop Bit (0-> 1 stop bit,1-> 2 stop bit)
020
0.0(dis)
0(dis)
0
999.9
999
1
1.0
3
0-LOCAL
0
Slave address
Baud rate
Parity
Datalog period
Timeout
Local/Remote select.
Stop bit
Parity: 0 -
1 -
2 -
NONE
ODD
EVEN
Min
Min
LOCAL/REMOTE

600
60(dis)
60
60
600
600
600
VV
VV
VV
VV
60(dis)
Min Default Max
Generator Under Voltage Shutdown
Generator Under Voltage Pre-Alarm
Generator Under Voltage Pre-Alarm Reset
Generator Over Voltage Shutdown
Generator Over Voltage Pre-Alarm
320
dis
350
440
60(dis) 600
60 600
dis
400
Generator Over Voltage Pre-Alarm Reset
VV
VV
Under volt shutdown
Under volt prealarm
Under volt reset
Over volt shutdown
Over volt prealarm
Over volt reset
Unit
Shutdown delay time
Generator Voltage Shutdown Delay Time
GENERATOR VOLT LEVEL ( )Generator-> levelVolt
0.0 10.0 1.0 Sec
75.0
30.0(dis)
75.0
75.0
Hz
30.0(dis)
Min Default Max
Generator Under Frequency Pre-Alarm
Generator Under Frequency Pre-Alarm Reset
Generator Over Frequency Shutdown
Generator Over Frequency Pre-Alarm
Generator Over Frequency Pre-Alarm Reset
dis
46.0
58.0
dis
54.0
Generator Frequency Shutdown Delay Time
Hz
Hz
Hz
Hz
30.0
30.0(dis)
30.0
75.0
75.0
Under freq prealarm
Under freq reset
Over freq shutdown
Over freq prealarm
Over freq reset
Shutdown delay time
Unit
GENERATOR LEVEL ( )FREQ Generator-> levelFrequency
75.0
75.0
Hz
30.0
Nominal Alternator Frequency 50.0
43.0 Hz
Nominal frequency
Under freq shutdown Generator Under Frequency Shutdown 30.0(dis)
0.0 10.0 1.0 Sec
4.2.2 Generator
8
Note: dis = disable
Min Default Max
Generator Under Current Pre-Alarm Reset
Generator Under Current Actions Delay Time
Generator CurrentOver IDMT Alarm
Generator Over Current Set
Generator Over Current Pre-Alarm
Generator Over Current Pre-Alarm Reset
Generator Over Current Actions Delay Time
Generator Short Circuit Current Set
Under cur. reset
Under cur. act.
Under act. delay time
Over cur. IDMT alarm
Over cur. set
Over cur. prealarm
Over cur. reset
Over cur. act.
Over act. delay time
Short circuit cur.
Unit
GEN ( )CUR LEVEL & ACT Generator->Current level & act.
Generator Under Current Set
Under cur. set
Under cur. prealarm Generator Under Current Pre-Alarm
0
0(dis)
0
0
9999
3
99
9999
9980
dis
2
9999
AV
AV
0
0(dis)
0
0(dis)
0
0
0(dis)
9999
9999
9999
3
99
9999
9999
1
dis
5
dis
2
9999
dis
AV
AV
AV
AV
AV
Sec
Sec
Generator Under Current Actions
Disable
Warning (Alarm Only, No Shutdown)
Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
Shutdown (Alarm And Shutdown)
0 -
1 -
2 -
3 -
Generator Over Current Actions
Disable
Warning (Alarm Only, No Shutdown)
Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
Shutdown (Alarm And Shutdown)
0 -
1 -
2 -
3 -
Unbalance Load Set
Unbalance Load Actions Delay Time
Unbalance load set
Unbalance load act.
Unbalance act. delay
0
0(dis)
0
9999
3
99
0
dis
2
AV
Sec
Unbalance Load
0 -
1 -
2 -
3 -
Actions
Disable
Warning (Alarm Only, No Shutdown)
Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
Shutdown (Alarm And Shutdown)
ENABL/DISBL DISBL

9999
9999
9999
9999
9999
9999
kVA
kVA
kVA
kVA
0
0(dis)
0
0
0(dis)
0
Min Default Max
Generator Under SetPower
Generator Under Pre-AlarmPower
Generator Under Pre-Alarm ResetPower
Generator Over SetPower
Generator Over Pre-AlarmPower
0
5
Generator Over Pre-Alarm ResetPower
kVA
kVA
Unit
Generator Over Delay TimePower Action
Reverse Power Set
Reverse Power Action Delay Time
0
-9999
0(dis)
0
99
0
3
99
2
0
0(dis)
2
Sec
kW
Sec
dis
0
0
dis
Reverse Power Actions
Disable
Warning (Alarm Only, No Shutdown)
Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
Shutdown (Alarm And Shutdown)
0 -
1 -
2 -
3 -
Under setpower
Under prealarmpower
Under resetpower
Over setpower
Over prealarmpower
Over resetpower
Over act. delay time
Reverse power set
Reverse power act.
Rv.pow.act.delay time
GEN LEVEL ( )POWER Generator->Power level
Generator Under Delay TimePower Action
0(dis)
0
3
99
0(dis)
2Sec
Generator Under Actions
Disable
Warning (Alarm Only, No Shutdown)
Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
Shutdown (Alarm And Shutdown)
Power
0 -
1 -
2 -
3 -
Under power act.
Under act. delay time
0(dis) 3 0(dis)
Generator Over Actions
Disable
Warning (Alarm Only, No Shutdown)
Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
Shutdown (Alarm And Shutdown)
Power
0 -
1 -
2 -
3 -
Over power act.
Min Default Unit
GENERATOR GENERAL ( )Generator->General Max
Sensing Options Generator Frq En/Dis
Sens.option gen.freq ENABL
ENABL/DISBL
0( )dis
Sensing Opt Pickup En/Dis & Flywheel DISBL1000
All Warnings Are Latched En/Dis
Sens.opt.pickup&flywh*2
All warning are latch ENABL/DISBL DISBL
9
Note: *2= This parameter is only available at Trans-MidiAUTO.MPU
dis = disable

4.2.3 Engine
ENABL/DISBL
Sec
Min Default Unit
ENGINE START OPTIONS ( )Engine->Starting options Max
Audible Alarm Prior To Starting En/Dis
Number Of Start Attempts
Cranking Time
Crank Rest Time
DISBL
3
5
1
1
10
99
10
5 99
Pickup Sensor Fail Delay
3.0
0.1 10.0
Horn prior start
No. of crank attemp
Cranking time
Crank rest time
Pickup fail dely*3Sec
Sec
10
Note: *3= This parameter is only available at Trans-MidiAUTO.MPU
dis = disable
Min Default Unit
ENGINE SPEED SETS ( )Engine->Speed settings Max
Engine Under Speed Shutdown
Engine Under Speed Prealarm
Engine Under Speed Prealarm Reset
dis
Engine Over Speed Shutdown
500(dis) 5000
500(dis) RPM
500
500 5000
Engine Over Speed Prealarm Reset
Engine Speed Shutdown Delay Time
500
1.0
RPM
RPM
RPM
RPM
RPM
Sec
5000
500(dis) 5000
5000
5000
10.0
Engine Over Speed Prealarm
Under speed shutdown
Under speed prealarm
Under speed reset
Over speed shutdown
Over speed prealarm
Over speed reset
Shutdown delay time
500
0.0
Nominal Speed 1500
500 5000 RPM
Nominal speed
dis
dis
dis
500(dis)
Min Default Unit
ENG. CRANK DISCONNECT ( )Engine->Crank disconnect Max
Crank Disconnect On Gen. Frequency
Crank Disconnect On Gen. Voltage
Crank Disconnect On Charge Alt. Voltage
30.0
Crank Disconnect On Oil Pressure En/Dis
Crank Disconnect On Oil Pressure Value
Check Oil Pressure Before Start
10.0 75.0 Hz
500
100
1.0
6000 RPM
300
60 (dis) 600 VV
dis
6.0 (dis) 30.0 VZ
1.0
30.0 BAR
Generator frequency
Engine speed
Generator volt
Charge alt. volt
Oil pres. enab./dis.
Oil pressure value
Check oil befor.start
Crank Disconnect On Engine RPM
ENABL/DISBL DISBL
ENABL/DISBL ENABL
Min Default
ENGINE PLANT BATTERY ( )Engine->Plant battery Max
Battery Undervolts Warning
Battery Undervolts Shutdown
Battery Undervolts Warning Reset
Battery Undervolts Volts Delay
Battery Overvolts Warning
Battery Overvolts Shutdown
11.0
dis
Battery Overvolts Warning Reset
6.0(dis)
6.0(dis)
30.0
30.0
11.5
6.0
1.0
0.0 9.9
29.0
dis
28.5
Charge Alternator Warning dis
30.0
30.0
30.0
6.0 30.0
Battery Overvolts Delay 1.0
0.0 9.9
30.0
6.0(dis)
6.0(dis)
6.0(dis)
Under volt warning
Under volt shutdown
Under volt reset
Under volt delay
Over volt warning
Over volt shutdown
Over volt reset
Over volt delay
Alt. chg. warning
Unit
VZ
VZ
VZ
VZ
VZ
VZ
Sec
Sec
VZ

11
dis = disable
Note: Parameters in this table are only available at= Trans-MidiAUTO.CAN*4
CANBUS ECU ( )Engine->CanBus ECU *4
Baud rate
J1939 ECU type
Device address
SPN version
Min Default UnitMax
07 4
32 0
0 255 17
1 3 1
kBaud
ECU remote control
Speed control enable
Oil pres cont. enab
Temp. control enable
ENABL
Device Address
0(dis)
SPN version
ECU Remote Control via J1939
Speed Control via J1939
Oil Pressure Control via J1939
Coolant Temperature Control via J1939
Speed correction 50
Speed Correction Value
%
0 100
Speed set point 1500
1500 1800/
Speed Set Point Selection
RPM
ENABL/DISBL
ENABL/DISBL
ENABL/DISBL
ENABL/DISBL
ENABL
DISBL
DISBL
Baud Rate:
0: 20, 1: 50, 2: 100, 3: 125,
4: 250, 5: 500, 6: 800, 7: 1.000
J1939 ECU Type Selection:
0 - Disable
1 - Standard
2 - Volvo EMS1
3 - Volvo EMS2
4 - Volvo EMS2b
5 - Volvo EDC3
6 - Volvo EDC4
7 - Deutz EMR2
8 - Deutz EMR3
9 - Perkins 1300
10 - Perkins ADEM3
11 - Perkins ADEM4
12 - Scania S6
13 - MAN MFR
14 - Cummins ISB
15 - Cummins CM570
16 - Cummins CM850
17 - Cummins CM2150E
18 - Cummins CM2250
19 - Detroit DDEC
20 - John Deere
21 - MTU ADEC
22 - MTU ECU8
23 - MTU ECU8 SAM
24 - Yuchai
25 - Kubota
26 - Baudouin WISE10B
27 - Baudouin WISE15
28 - Perkins 1600
29 - Perkins A4E2
30 - Perkins A5E2
31 - Perkins A5E2v2
32 - Hatz EDC17

12
Min Default Unit
CANBUS ERROR SET ( )Engine->CanBus error set *5Max
Can Fault Actions:
0- Disable
1- Warning Non-Latching
2- Warning (Alarm Only, No Shutdown)
3- Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
4- Shutdown (Alarm And Shutdown)
0
0 2
0
0(dis) 4
CAN fault activation
CAN fault actions
SecCan Fault Delay 10
2 250
CAN fault delay
Can Fault Activation:
0- Active From Starting
1- Active From Safety On
2- Always Active
J1939 Amber Warning Lamp Actions:
0- Disable
1- Warning Non-Latching
2- Warning (Alarm Only, No Shutdown)
3- Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
4- Shutdown (Alarm And Shutdown)
2
0 2
0
0(dis) 4
Amber warn.activation
Amber warn.actions
SecJ1939 Amber Warning Lamp Delay 2
0 250
Amber warn.delay
J1939 Amber Warning Lamp Activation:
0- Active From Starting
1- Active From Safety On
2- Always Active
J1939 Red Stop Lamp Actions:
0- Disable
1- Warning Non-Latching
2- Warning (Alarm Only, No Shutdown)
3- Electrical Trip (Alarm/Off Load Generator
Followed By Shutdown After Cooling)
4- Shutdown (Alarm And Shutdown)
2
0 2
0
0(dis) 4
Red stop activation
Red stop actions
SecJ1939 Red Stop Lamp Delay 2
0 250
Red stop delay
J1939 Red Stop Lamp Activation:
0- Active From Starting
1- Active From Safety On
2- Always Active
Note: = Parameters in this table are only available at Trans-MidiAUTO.CAN
dis = disable
*5

Min Default
LOAD EXERCISE ( )Engine->Load exercise Max Unit
0-DISABLE
Disable/enable select Disable, No Load or On Load Selection 0-DISABLE
1-NO LOAD
2-ON LOAD
13
Note: dis = disable
Min Default
ENGINE MAINTENANCE ( )Engine->Maintenance Max
Running Hours Interval
Maintenance Date Interval
Force Engine Shutdown When Maintenance Is Due
Engine Running Hour (Lsb)
600
Engine Running Hour
0(dis) 9999
Engine Running Hour(Msb)
ENABL/DISBL
0
0 255
DISBL
0
0
0(dis) 12 6
0 255
0 14
Maint. date interval
Eng. stop when maint
Eng. running hour(lsb)
Eng. running hour
Eng. running hour(msb)
Running hour interval
Unit
Hour
Month
Maintenance Okay NO
Maintenance okay YES/NO
Min Default Max
Exercise Disable or Enable
Exercise Start Time on Monday1
Exercise Start Time on Monday2
Exercise Start Time on Monday3
Exercise Start Time on Monday4
Exercise Stop Time on Monday1
Exercise Stop Time on Monday2
Exercise Stop Time on Monday3
Exercise Stop Time on Monday4
Exercise Start Time on Tuesday1
Exercise Start Time on Tuesday2
Exercise Start Time on Tuesday3
Exercise Start Time on Tuesday4
Exercise Stop Time on Tuesday1
Exercise Stop Time on Tuesday2
Exercise Stop Time on Tuesday3
Exercise Stop Time on Tuesday4
Exercise Start Time on Wednesday1
Exercise Start Time on Wednesday2
Exercise Start Time on Wednesday3
Exercise Start Time on Wednesday4
Exercise Start Time on Thursday1
Exercise Start Time on Thursday2
Exercise Start Time on Thursday3
Exercise Start Time on Thursday4
Disable/enable select
Start time on monday1
Start time on monday2
Start time on monday3
Start time on monday4
Stop time on monday1
Stop time on monday2
Stop time on monday3
Stop time on monday4
Start time on tues.1
Start time on tues.2
Start time on tues.3
Start time on tues.4
Stop time on tuesday1
Stop time on Tuesday2
Stop time on tuesday3
Stop time on tuesday4
Start time on wednes.1
Start time on wednes.2
Start time on wednes.3
Start time on wednes.4
Start time on thurs.1
Start time on thurs.2
Start time on thurs.3
Start time on thurs.4
Unit
Stop time on wednes.1
Stop time on wednes.2
Stop time on wednes.3
Stop time on wednes.4
Stop time on thurs1 .
Stop time on thurs2 .
Stop time on thurs3 .
Stop time on thurs4 .
Exercise Stop Time on Wednesday1
Exercise Stop Time on Wednesday2
Exercise Stop Time on Wednesday3
Exercise Stop Time on Wednesday4
Exercise Stop Time on Thursday1
Exercise Stop Time on Thursday2
Exercise Stop Time on Thursday3
Exercise Stop Time on Thursday4
EXERCISE ( )Engine->Exercise
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
DISBL ENABL/ DISBL

14
Note: dis = disable
Min Default Unit
ENGINE GENERAL ( )Engine->General Max
Engine Fuel Selection 1-DIESEL
Stop Solenoid Time 1 2099
Ignition Delay 1 599 Sec
Gas Valve Delay 1 599 Sec
Minimum Ignition Speed 10 2001500 RPM
Fuel selection
Stop solenoid time
Ignition delay
Gas valve delay
Min. of ignition speed
Sec
Choke time Choke Time Sec
0.0 0.830.0
0-GAS
1-DIESEL
2-GASOLINE
Exercise Start Time on1 Friday
Exercise Start Time on2 Friday
Exercise Start Time on3 Friday
Exercise Start Time on4 Friday
Exercise Start Time on1 Saturday
Exercise Start Time on2 Saturday
Exercise Start Time on3 Saturday
Exercise Start Time on4 Saturday
Exercise Start Time on day1 Sun
Exercise Start Time on day2 Sun
Exercise Start Time on day3 Sun
Exercise Start Time on day4 Sun
Exercise Stop Time on1 Friday
Exercise Stop Time on2 Friday
Exercise Stop Time on3 Friday
Exercise Stop Time on4 Friday
Exercise Stop Time on day1 Satur
Exercise Stop Time on day2 Satur
Exercise Stop Time on day3 Satur
Exercise Stop Time on day4 Satur
Exercise Stop Time on day1 Sun
Exercise Stop Time on day2 Sun
Exercise Stop Time on day3 Sun
Exercise Stop Time on day4 Sun
Start time on day1 fri
Start time on day2 fri
Start time on day3 fri
Start time on day4 fri
Start time on1 satur.
Start time on2 satur.
Start time on3 satur.
Start time on4 satur.
Start time on day1 sun
Start time on day2 sun
Start time on day3 sun
Start time on day4 sun
Stop time on day1 fri
Stop time on day2 fri
Stop time on day3 fri
Stop time on day4 fri
Stop time on1 satur.
Stop time on2 satur.
Stop time on3 satur.
Stop time on4 satur.
Stop time on day1 sun
Stop time on day2 sun
Stop time on day3 sun
Stop time on day4 sun
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
23.59
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
H.Min
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00

15
4.2.4 Inputs
0 - Disable
1 - Enable From Safety
On (3min. delayed)
2 - Always Enable
Min Default Unit
SENDER INPUTS ( )Inputs->Sender inputs Max
Oil Pressure Input Type
Oil Pressure Pre-Alarm
Oil Pressure Sensor Break
Oil Pressure Pre-Alarm Reset
Coolant Temperature Input Type
1.2
0.0 (dis) 30.0 BAR
1.4
0.0 30.0 BAR
1.0
0.0 30.0 BAR
0 - Not Used (Disable)
1 - Digital NC
2 - Digital NO
3 - VDO 5 BAR
4 - VDO 7 BAR
5 - VDO 10 BAR
6 - DATCON 5 BAR
7 - DATCON 7 BAR
8 - MURPHY 7 BAR
9 - User Configured
90
0 (dis) 300
88
0 300
95
0 300
0 (dis) 3000 %
0 3000
3000
Temperature Sensor Break
High Temperature Pre-Alarm
Oil Pressure Shutdown
High Temp. Pre-Alarm Reset
High Temperature Shutdown
C
C
C
Temp. sensor break
High temp. prealarm
High temp. reset
High temp. shutdown
Conf. AI1 type
Conf. AI1 low prealrm
Cnf.AI1 sens err.shut
Temp. input type
Oil pressure shutdown
Oil pressure reset
Oil pressure prealarm
Oil pres.sensor break
Oil press. input type
%
%
0 (dis)
60
0 (dis) 70
Low Temperature Warning C
Low temp. warning
Conf. AI1 unit
Configurable Analog Input-1 Type
Conf. AI1 low shutdwn
0 (dis)
0 - Not Used (Disable)
1 - Digital NC
2 - Digital NO
3 -
4 - 5
5 - DATCON
6 - MURPHY
7 - PT100
8 - User Configured
VDO 120 ºC
VDO 1 0 ºC
0 (dis)
0 - Not Used (Disable)
1 - Digital NC
2 - Digital NO
3 - VDO OHM (10-180)
4 - VDO TUBE (90-0)
5 - US OHM (240-33)
6 - EMS OHM (0-190)
7 - FORD (73-10)
8 - User Configured
0 (dis)
0 (dis)
0 (dis)
0 (dis)
Oil Pressure Unit
Oil pressure unit BARBAR/PSI/KPA
Coolant Temperature Unit
Temperature unit ºCºC/ºF
BAR/PSI/KPA/ºC/ºF/%/Lt %
Configurable Analog Input-1 Unit
Configurable Analog Input-1
Low Pre-Alarm
Configurable Analog Input-1
Sensor error shutdown
Conf. AI1 low reset
Configurable Analog Input-1
Low Reset
Configurable Analog Input-1
Low Shutdown
0 (dis)
0 (dis) 300
Coolant Heater Control On C
Heater control ON
0300
Coolant Heater Control Off C
Heater control OFF
45
DISBL ENABL/ ENABL
5
0 9999
Water Pump On Time
Water pump on time
09999
Water Pump Off Time Sec
Water pump off time
5
Sec
DISBL ENABL/ ENABL
0 (dis)

16
Note: dis = disable
0%
75
Conf. AI1 control OFF Configurable Analog Input-1
control OFF
3000
0 (dis)
0 (dis) 3000 %
Conf. AI1 control ON
Configurable Analog Input-1
control ON
Conf. AI1 high shutd.
Configurable Analog Input-1
High Shutdown
0 (dis) 3000 %
0 (dis)
90
0 3000 %
Conf. AI1 high reset
Configurable Analog Input-1
High Reset

17
Min Default Unit
SENDER LINEARISATION ( )Inputs->Sender linearisation Max
Oil Pressure Sender Point-1
Oil Pressure Sender Point-2
Oil Pressure Sender Point-3
Oil Pressure Sender Point-4
Oil Pressure Sender Point-5
Oil Pressure Sender Point-6
Oil Pressure Sender Point-7
Oil Pressure Sender Point-8
Oil Pressure Sender Point-9
Oil Pressure Sender Point-10
Temperature Sender Point-1
Temperature Sender Point-2
Temperature Sender Point-3
Temperature Sender Point-4
Temperature Sender Point-5
Temperature Sender Point-6
Temperature Sender Point-7
Temperature Sender Point-8
Temperature Sender Point-9
Temperature Sender Point-10
Configurable Analog Input-1 Sender Point-1
Configurable Analog Input-1 Sender Point-2
Configurable Analog Input-1 Sender Point-3
Configurable Analog Input-1 Sender Point-4
Configurable Analog Input-1 Sender Point-5
Oil Pressure Point-1
Oil Pressure Point-2
Oil Pressure Point-3
Oil Pressure Point-4
Oil Pressure Point-5
Oil Pressure Point-6
Oil Pressure Point-7
Oil Pressure Point-8
Oil Pressure Point-9
Oil Pressure Point-10
Temperature Point-1
Temperature Point-2
Temperature Point-3
Temperature Point-4
Temperature Point-5
Temperature Point-6
Temperature Point-7
Temperature Point-8
Temperature Point-9
Temperature Point-10
Configurable Analog Input-1 Point-1
Configurable Analog Input-1 Point-2
Configurable Analog Input-1 Point-3
Configurable Analog Input-1 Point-4
Configurable Analog Input-1 Point-5
15
31
49
66
85
101
117
132
149
178
579
404
342
250
179
136
103
77
67
63
10
30
50
70
90
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
1300
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
10.0
28
35
40
50
60
70
80
90
95
98
0
11
22
33
44
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BAR
BAR
BAR
BAR
BAR
BAR
BAR
BAR
BAR
BAR
ºC
ºC
ºC
ºC
ºC
ºC
ºC
ºC
ºC
ºC
%
%
%
%
%
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
30.0
30.0
30.0
30.0
30.0
30.0
30.0
30.0
30.0
30.0
300
300
300
300
300
300
300
300
300
300
3000
3000
3000
3000
3000
Oil pressure sender 1
Oil pressure sender 2
Oil pressure sender 3
Oil pressure sender 4
Oil pressure sender 5
Oil pressure sender 6
Oil pressure sender 7
Oil pressure sender 8
Oil pressure sender 9
Oil pressure sender 10
Temperature sender 1
Temperature 2sender
Temperature 3sender
Temperature 4sender
Temperature 5sender
Temperature 6sender
Temperature 7sender
Temperature 8sender
Temperature 9sender
Temperature 0sender 1
Conf. AI1 sender 1
Conf. AI1 sender 2
Conf. AI1 sender 3
Conf. AI1 sender 4
Conf. AI1 sender 5
Oil pressure 1
Oil pressure 2
Oil pressure 3
Oil pressure 4
Oil pressure 5
Oil pressure 6
Oil pressure 7
Oil pressure 8
Oil pressure 9
Oil pressure 10
Temperature 1
Temperature 2
Temperature 3
Temperature 4
Temperature 5
Temperature 6
Temperature 7
Temperature 8
Temperature 9
Temperature 01
Conf. AI1 value 1
Conf. AI1 value 2
Conf. AI1 value 3
Conf. AI1 value 4
Conf. AI1 value 5

18
Configurable Analog Input-1 Sender Point-6
Configurable Analog Input-1 Sender Point-7
Configurable Analog Input-1 Sender Point-8
Configurable Analog Input-1 Sender Point-9
Configurable Analog Input-1 Sender Point-10
Configurable Analog Input-1 Point-6
Configurable Analog Input-1 Point-7
Configurable Analog Input-1 Point-8
Configurable Analog Input-1 Point-9
Configurable Analog Input-1 Point-10
110
130
150
170
190
0
0
0
0
0
1300
1300
1300
1300
1300
55
66
77
88
100
0
0
0
0
0
R
R
R
R
R
3000
3000
3000
3000
3000
Conf. AI1 sender 6
Conf. AI1 sender 7
Conf. AI1 sender 8
Conf. AI1 sender 9
Conf. AI1 sender 10
Conf. AI1 value 6
Conf. AI1 value 7
Conf. AI1 value 8
Conf. AI1 value 9
Conf. AI1 value 10
%
%
%
%
%

19
Note-1 : x = 1(input ), 2( ), 3( ), 4( ), or 5input input input (input )
-
-
25 -
26 - Low Oil Level
26 -
dis = disable
Note-
Note-3 :
-1 -2 -3 -4 -5
Emergency Stop (for only input-1)
Low Oil Pressure (for only input-4)
High Temperature (for only input-5)
(for only input-4)
Emergency Stop No-Latching (for only input-1)
2 : 25
25
Min Default Unit
CONF. INPUT-X ( )Inputs->Conf. input-x Max
20(dis)
10
4
20
0
2500 Sec
0
Dis,user conf.or list
Polarity
Indication
Activation
Select from list
Active delay
0- Disable
1- User Configured
2- Select From List
0- Normally Open (Close To Activate)
1- Normally Close (Open To Activate)
If User Configured
0- Status
1- Warning Non-Latching
2- Warning Latching
3- Electrical Trip
4- Shutdown
If User Configured
0- Active From Starting
1- Active From Safety On
2- Always Active
Input active delay
in =26
in2=24
in3=24
in4=26
in5=25
1 in =25
in2=0
in3=4
in4=25
in5=25
1
in1, 2=2
in3=1
in4, 5=2
in1=0
in2=0
in3=4
in4=0
in5=0
in1, 2=2
in3, 4=2
in5=2
in1, 2=0
in3=5
in4, 5=0
in1, 3=1
in2, 4=0
in5=0
If Select From List
0-Remote Start On Load
1-Remote Start Off Load
2-Reserved
3-Remote Control Active
4-Reserved
5-Reserved
6-Simulate Auto Button
7-Simulate Test Button
8-Reserved
9-Simulate Start Button
10-Simulate Stop Button
11-Generator Closed Auxiliary
12-Generator Load Inhibit
13-Reserved
14-Reserved
15-Auto Restore Inhibit
16-Auto Start Inhibit
17-Panel Lock
18-Scheduled Runs(Exercise) Inhibited
19-Reserved
20-Transfer To Generator/Open Mains
21-Reserved
22-Remote Inhibit
23-Being Found Alive
24-Reserved
25 - Emergency Stop (for only input-1)
25 - Low Oil Pressure (for only input-4)
25 - High Temperature (for only input-5)
26 - Low Oil Level (for only input-4)
26 - Emergency Stop No-Latching (for only input-1)

20
4.2.5 Outputs
Min Default Unit
CONF. OUTPUT-1 ( )Outputs->Conf. output-1 Max
010
1310 43
Polarity
Function
0- Normally Open (Close To Activate)
1- Normally Close (Open To Activate)
0-NOT USED
1-AIR FLAP CONTROL
2-ALARM RESET
3-AUDIBLE ALARM
4-AUTO START INHIBIT
5-RESERVED
6-BATTERY HIGH VOLTAGE
7-BATTERY LOW VOLTAGE
8-CALLING FOR SCHEDULED RUN(EXERCISE)
9-CAN ECU POWER
10-CAN ECU STOP
11-CHARGE ALTERNATOR FAILURE
12-COMMON ALARM
13-COMMON ELECTRICAL TRIP ALARM
14-COMMON SHUTDOWN ALARM
15-COMMON WARNING ALARM
16-COOLING FAN AFTER START
17-COOLING FAN AFTER STOP
18-COOLANT TEMPERATURE HIGH PRE-ALARM
19-COOLANT TEMPERATURE HIGH SHUTDOWN
20-COOLING DOWN TIMER IN PROGRESS
21-CRANK RELAY ENERGISED
22-DELAYED ALARMS ACTIVE
23-DIGITAL INPUT1 ALARM
24-DIGITAL INPUT2 ALARM
25-DIGITAL INPUT3 ALARM
26-DIGITAL INPUT4 ALARM
27-DIGITAL INPUT5 ALARM
28-RESERVED
29-RESERVED
30-RESERVED
31-RESERVED
32-RESERVED
33-RESERVED
34-RESERVED
35-RESERVED
36-RESERVED
37-RESERVED
38-RESERVED
39-EMERGENCY STOP
40-FAIL TO START ALARM
41-FAIL TO STOP ALARM
42-CONF. AI1 CONTROL
43-FUEL RELAY ENERGISED
44-GAS ENGINE IGNITION OUTPUT
45-GENERATOR AT REST
46-GENERATOR AVAILABLE
47-GENERATOR CLOSED AUXILIARY
48-GENERATOR FAILED TO CLOSE
49-GENERATOR FAILED TO OPEN
50-GENERATOR HIGH FREQUENCY PRE-ALARM
51-GENERATOR HIGH FREQUENCY SHUTDOWN
52-GENERATOR HIGH VOLTAGE PRE-ALARM
53-GENERATOR HIGH VOLTAGE SHUTDOWN
54-GENERATOR LOAD INHIBIT
55-GENERATOR LOW FREQUENCY PRE-ALARM
56-GENERATOR LOW FREQUENCY SHUTDOWN
57-GENERATOR LOW VOLTAGE PRE-ALARM
58-GENERATOR LOW VOLTAGE SHUTDOWN
59-GENERATOR STOPPING
60-GENERATOR OPEN BREAKER
61-HORN OUTPUT LATCHED
62-HORN OUTPUT PULSED
63-LAMP TEST
64-RESERVED
65-LOSS OF MAGNETIC PICK-UP SPEED SIGNAL
66-LOW TEMPERATURE
67-MAINTENANCE DUE ALARM
68-RESERVED
69-RESERVED
70-RESERVED
71-RESERVED
72-RESERVED
73-RESERVED
74-RESERVED
75-RESERVED
76-RESERVED
77-RESERVED
78-NO LOADING COMMAND
79-OIL PRESSURE LOW PRE-ALARM
80-OIL PRESSURE LOW SHUTDOWN
81-CONF.AI1.HIGH PREA
82-CONF.AI1.HIGH SHUT
83-OVER CURRENT PRE-ALARM
84-OVER CURRENT
85-OVER POWER PRE-ALARM
86-OVER POWER SHUTDOWN
87-OVERSPEED PRE-ALARM
88-OVERSPEED SHUTDOWN
89-PANEL LOCK
90-PRE-HEAT(during preheat timer)
91-PRE-HEAT(until end of cranking)
92-PRE-HEAT(until end of warming)
93-PRE-HEAT(until end safety on)
94-REMOTE START PRESENT
95-REMOTE STOP DELAY IN PROGRESS
96-SHORT CIRCUIT
97-SMOKE LIMITING
98-STARTING ALARM
99-STARTING ALARMS ARMED
100-STOP RELAY ENERGISED
101-SYSTEM IN AUTO MODE
102-SYSTEM IN MANUAL MODE
103-SYSTEM IN STOP MODE
104-SYSTEM IN TEST MODE
105-UNDER CURRENT PRE-ALARM
106-UNDER CURRENT
107-UNDER POWER PRE-ALARM
108-UNDER POWER SHUTDOWN
109-UNDERSPEED PRE-ALARM
110-UNDERSPEED SHUTDOWN
111-WAITING FOR GENERATOR
112-RESERVED
113-LOAD SUPPLY FROM GENERATOR
114-RESERVED
115-CONFIGURABLE ANALOG INPUT 1 LOW PRE-ALARM
116 CONFIGURABLE ANALOG INPUT 1 LOW SHUTDOWN
117-RESERVED
118-RESERVED
119-RESERVED
120-RESERVED
121-CHOKE ACTIVE
122-REMOTE CONTROL ACTIVE
123-REVERSE POWER
124-RESERVED
125-RESERVED
126-RESERVED
127-RESERVED
128-HEATER CONTROL
129-REMOTE OUTPUT
130-UNBALANCE LOAD
131-WATER PUMP
(only available at Trans-MidiAUTO.CAN)
(only available at Trans-MidiAUTO.CAN)
(only available at Trans-MidiAUTO.MPU)
-