Erreka DINGO Operating instructions

5
DINGO
Quick installation and programming guide English
WARNING
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The most recent version of this guide and the
installation manual are available at the "Downloads" section on Erreka's website:
http://www.erreka-automation.com
The options and functions described in this guide apply for the firmware version indicated on the circuit. The
firmware, as part of a process of continuous improvement, is subject to new functionalities or upgrades being
included as a result of new versions which are not necessarily compatible with previous ones. For this reason,
some options or functions may differ or be unavailable if your firmware is older than shown in this guide.
Electrical wiring
A: Main power supply
B/E: Flashing light with
antenna
C: Photocells (Tx / Rx)
D: Pushbutton/wall key
E259A
Install the rack at a height between 75 and 95 mm.
90 mm is recommended as the reference height.
Elements of the complete installation
Assembly levels
180º
D259A
180º
D259B
Unlocking
Motorised operation locking:
•Insert the key and turn it anti-clockwise 180º as far as
it will go. The pinion will return to its work position, in
contact with the rack.
•Activate a key device in order for the gate to carry out
a "reset".
Unlocking Locking
Unlocking for manual operation:
•Insert the key (1) and turn clockwise 180º without
forcing it: the rack drive pinion will come down from
its operating position, releasing the rack.
MSM-043/01 Firmware V1.0 or later

6
ADN01
General connections
L: line
N:neutral
T: earth
F:mainsfuse
230Vac: 2.5A
125Vac: 4A
Disconnect the power
supply before connecting
or disconnecting any
component.
The A.T., A.P. SG.C, SG.A and STOP devices must be voltage-free
in order to prevent any damage to the control board.
DL13 24Vac power supply
DL36 5Vdc power supply
DL37 Closing relay activated
DL38 Opening relay activated
M259C
EnterEsc
D1 and D2:
CL (static) Gate closed
CL (flashing) Gate closing
OP (static) Gate open
OP (flashing) Gate opening
PC (flashing) Pedestrian door closing
PO (static) Pedestrian door open
PO (flashing) Pedestrian door opening
XX (countdown) Gate on standby
StOP Operator unlocked
PA (static) Pause (operation not complete)
rS (flashing) Gate searching for close position (reset)
D3 and D4:
C4 Opening safety device activated
C5 Closing safety device activated
E1 Encoder motor shutdown
F1 Force limit exceeded
bA (static) Battery working
bA (flashing) Battery voltage too low
(the board does not carry out any operations)
Ftço Photocells defective (testing)
Display indications

7
P71Y
P71X
P71Z
Turning direction change and check (C1)
P71V
P71W
This operation is only necessary if the operator opens the leaf instead of closing it when making a reset (rS).
I
II
P157E
Total opening radio code programming P1 (with RSD receiver only, C801)
 If a receiver other than
RSD
is used, see the cor-
responding instructions.
Select the option C801
(RSD receiver) before
starting programming.
Pedestrian opening radio code programming, P2 (with RSD receiver only, C801)
This procedure is the same as for total opening, but using parameter P2 instead of P1.
I
II
OWait whilst the gate
carries out the
open/close
Open/close programming (P3)

8
Complete programming chart
D1 D2 Parameter D3 D4 Preset option Options or values
C1Motor turning direction 01x
02
4Opening safety device (photocell or strip) 00xDevice not installed
10 Device without testing
11 Device with testing
5Closing safety device (photocell or strip)
Closing photocell with C520 or C521, also
prevents the start of gate opening
00xDevice not installed
10 Device without testing
11 Device with testing
20 Device without testing
21 Device with testing
8Radio receiver 01 RSD card (non-decoding)
02xTwin-channel decoder card
P1Total opening radio code programming oç
2Pedestrian opening radio code programming oç
3Gate travel programming oç
F1Functioning mode 01 Automatic
02xStep-by-step
2Standby in automatic mode 0...5ÿ 0...915 59= 59 sec.; 2ÿ5 = 2 min. 50 sec, etc
3Pedestrian opening 00xPedestrian opening is not carried out
10 10% of total opening
20 20% of total opening
30 30% of total opening
40 40% of total opening
50 50% of total opening
A0Flashing light 01xNo pre-warning
02 With pre-warning
1Garage light time 0...5ÿ 0...903 59= 59 secs; 2ÿ5 = 2 min. 50 secs, etc
2Gate speed 01...503 01: minimum speed;
05: maximum speed
3Slow down speed 01...503 01: minimum speed;
05: maximum speed
4Slowdown distance 00...503 00: minimum distance;
05: maximum distance
5Reverse after closing (to offset the expansion
of the gate)
A50x: stops in selected position without
making contact
A51x: makes contact and reverses back to
the selected position
0...10...904 x0: no reverse;
x9: maximum reverse
6Maximum force 0...10...908 01: minimum force; 10: maximum force
7Closing photocell used during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
8Pushbutton operation during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
9Opening mode 01xOpening in accordance with the mode
selected in the main functions (F)
02 Collective opening (the control board
does not obey the key commands during
opening)
03 Step-by-step opening (the gate stops if
a key device is activated during opening.
The gate closes when operated again)
ç1Operations carried out XX Indicates the hundreds of cycles
completed (for example, 68 indicates
6,800 cycles completed)