FabiaTech FB2530 Series User instructions

Version 1.3 FB2530 Series User’s Quick Setting Page 1/3
1. Brief
The FB2530 is an all-in-one, 3.5" disk size, NS Geode low power CPU board. This user’s quick
setting provides the jumper settings, connector location, and their pin assignment.
2. Board Placement
J5
J3
J1 CN3 CN6 J6
CN8
CN4
JP1
CN1
J2
BUS1
CN2 DB1 J7 CN11CN9
LM1
DB2 CN10
CN5 CN7
JP6
J4
JP3
JP4
JP5
JP2
J8
JP7
3. Packing List
1 FB2530 all-in-one CPU board.
1 44-pin hard disk drive interface cable.
1 20-pin to 34-pin floppy drive interface cable.
1 serial port adapter cable and 1 parallel port interface cable.
1 PS/2 keyboard and mouse port adapter cable.
1 audio adapter cable with FB4612B transfers board.
1 6-pin power adapter cable.
1 compact disc includes software utility.
1 hard copies of this quick setup manual.
4. Features
* On-board 200~300 MHz NS Geode GX1 CPU.
* NS CS5530A chipset with UMA architecture.
* 1 So-DIMM socket for up to 128MB PC-100 SDRAM.
* One or two 100/10 base-T Ethernet ports.
* Provides CRT and LCD with 1.5MB to 4MB shared memory.
* 1 parallel port, 1 RS-232, 1 RS-232/485/IrDA.
* 1 floppy port and 1 PCI IDE interface.
* PS/2 compatible keyboard and mouse interface.
* Provides header for external speaker.
* Flash BIOS with easy upgrade utility.
* AC97 audio function supports Line-In, Line-Out, and Mic-In.
* 2 USB ports and software programmable watchdog timer.
* 2 TTL input lines and 2 TTL output lines.
* Power requires +5V - 1.3A maximum, +12V - 0.1A maximum.
* 3.5" disk size, 145 mm x 102 mm (5.7” x 4.0”)
5. Connectors, Headers and Their Relative Jumpers
A. Reset Switch (J7)
J7 is a push bottom switch for system reset. Push and release the bottom will cause hardware
reset of FB2530 and restart system booting.
B. Power Connector (J6: 6-pin 2.5mm JST)
J6 Pin 1: Ground Pin 4: Ground
Pin 2: +5V Pin 5: Ground
Pin 3: +5V Pin 6: +12V
6 1
C. Keyboard and Mouse Connector (CN1: 6-pin 2.0mm JST))
CN1 provides PS/2 keyboard and mouse interface, use the included adapter cable to connect
between CN1 and standard PS/2 devices.
Pin 1: Mouse Data
Pin 2: Keyboard Data
Pin 3: Ground
Pin 4: +5V
Pin 5: Mouse Clock
Pin 6: Keyboard Clock
6
CN1
1
D. Serial Port Connectors and Jumpers (DB1, CN2, J2, J4, JP3, JP4, JP5, and JP6)
The serial port1 supports RS-232 only and the serial port 2 supports RS-232, RS-485 and
InfraRed interface. JP6 is used to select RS-232 or RS-485 of serial port 2 and JP3 provides
terminator select of RS-485 mode. Both ports also provide jumper for power output selection.
©2001-2002 FabiaTech Corp.

Version 1.3 FB2530 Series User’s Quick Setting Page 2/3
The following table lists jumpers and connectors of these 2 serial ports.
Functional connector, header,
and jumper of serial ports Serial Port 1 Serial Port 2
RS-232 Signal DB1 CN2
RS-485 Signal - CN2
RS-485 Select - JP6 & JP3
IrDA Interface - J4
Touch Screen Interface - J2
Power Output Select JP4 JP5
The included serial port cables are use to transfer CN2 to 9-pin D-type male connector. The
following table and figures show the pin definitions of DB1, CN2, J2, J4, JP3, JP4, JP5 and
JP6:
DB1 RS-232 CN2 RS-232 RS-485 9-pin D-sub
1 -DCD1 1 -DCD2 - 1
6 -DSR1 2 -DSR2 - 6
2 RXD1 3 RXD2 485- 2
7 -RTS1 4 -RTS2 7
3 TXD1 5 TXD2 485+ 3
8 -CTS1 6 -CTS2 8
4 -DTR1 7 -DTR2 4
9 -RI1 8 -RI2 9
5 Ground1 9 Ground2 5
Case Case Ground 10 Case Ground Case Ground Case
E. Parallel Port Connector (CN3: 26-pin 2.0mm IDC)
The included printer interface cable is used to transfer 26-pin connector into standard 25-pin
D-sub connector.
F. Floppy Connector (CN5: 20-pin 2.0mm IDC)
The included floppy drive interface cable is used to transfer 20-pin connector into standard
34-pin connector. Note that the included floppy cable supports only 720KB, 1.44MB, and
2.88MB floppy disk drives, not for 360KB and 1.2MB.
G. IDE Hard Disk Connector (CN7: 44-pin 2.0mm IDC)
Use 44-pin hard disk cable you can attach up to two 2.5” hard disk drives.
H. External Speaker Header (J5)
I. LAN Connectors and LED Indicators (CN9 & CN10: RJ45)
CN9 and CN10 both is RJ45 connector with 2 LEDs for LAN status. The left side LED (orange)
indicates data is accessing and the right side LED (green) indicates on-line status. (When
lighted indicates on-line and off indicates off-line). CN9 supports LAN port #1 and CN10 for LAN
port #2.
CRT Connector (DB2)
J5 Pin 1: Speaker+
Pin 2: Speaker-
2 1
1
5 10
DB2
(
Front View
)
6
11
15
Pin 1: Red
Pin 2: Green
Pin 3: Blue
Pin 13: Hsync
Pin 14: Vsync
Pin 12: DDC Data
Pin 15: DDC Clock
Pin 5 & 10: Digital Ground
Pin 6,7,8: Analog Ground
Others: Not Used
Factory Preset
None
Note: The selected power source will
drive the “–RI” signal pin if JP4,
or JP5 were located on the
power output position.
1 2
1 2
1 2 CN9 and CN10 Pin 1: TPTX+
Pin 2: TPTX-
Pin 3: TPRX+
Pin 4: FBG1
Pin 5: FBG1
Pin 6: TPRX-
Pin 7: FBG2
Pin 8: FBG2
3 4
3 4
3 4
65 JP4/JP5 +5V
65 JP4/JP5 +12V
65 JP4/JP5
1
8
Pin 1: TXD2
Pin 2: RXD2
Pin 3: Ground
3
JP3 1 J2
1 (Front View)
1
3 3 Touch Screen Interface
Terminator On
Terminator Off
Factor
y
Preset Infra Red Header
Pin 1: VCC
Pin 2: Not Used
Pin 3: IRRX
Pin 4: Ground
Pin 5: IRTX
1
JP6
3 1 3
1 J4
RS-232 mode RS-485 mode 5
Factor
y
Preset
©2001-2002 FabiaTech Corp.

Version 1.3 FB2530 Series User’s Quick Setting Page 3/3
J. LCD Connectors (CN6 & CN8)
CN6 is 18-bit LCD interface connector and CN8 provides control signals and power source for
LCD inverter.
CN6 Signal CN6 Signal CN6 Signal CN6 Signal
1 +5V 21 FPD8 2 +5V 22 FPD9
3 Ground 23 FPD10 4 Ground 24 FPD11
5 +3.3V 25 N.C. 6 +3.3V 26 N.C.
7 N.C. 27 FPD12 8 Ground 28 FPD13
9 N.C. 29 FPD14 10 N.C. 30 FPD15
11 FPD0 31 FDP16 12 FPD1 32 FPD17
13 FPD2 33 Ground 14 FPD3 34 Ground
15 FPD4 35 FPCLK 16 FPD5 36 FPVSYNC
17 N.C. 37 DE 18 N.C. 38 FPHSYNC
19 FDP6 39 ENABLK 20 FPD7 40 ENAVEE
Note 1: N.C. means not connected, it is reserved for upgraded signals.
Note 2: If any trouble when connecting FB2530 with LCD panels, you could contact technical
support division of FabiaTech Corporation.
K. USB Connector (CN11)
CN11 is a standard double port USB connector. The upper port is USB#1 and the lower port is
the USB#2.
L. Audio Connector (CN4: 10-pin 2.0mm IDC)
Use the included cable and FB4612B adapter board to realize audio I/O functions.
CN4 Signal CN4 Signal
1 CD-In-L 2 Line-In-L
3 CD-In-R 4 Line-In-R
5 Analog Ground 6 +5V
7 Line-Out-L 8 Mic-In
9 Line-Out-R 10 Ground
M. TTL I/O Connector (J3)
N. External Battery Header and Battery Select Jumper (J1 & JP1)
J1 is used to connect an external battery pack if on-board Lithium battery is empty, and please
setting JP1 properly of on-board battery or external battery.
O. SoDIMM Socket (DIMM1)
The DIMM1 socket on the solder side accepts 32MB to 128MB PC-100 SDRAM modules.
P. PC/104 Connectors (BUS1: 64-pin IDC & 40-pin IDC)
6. Others
A. Rear Panel LED Indicator (LM1)
J3 J3 Signal Bit Location J3 Signal Bit Location
1 Input 0 Bit 0 of 78H 2 Output 0 Bit 0 of 78H
3 Input 1 Bit 1 of 78H 4 Output 1 Bit 1 of 78H
5 +5V - 6 Ground -
6 5
1
2
Pin 1: Battery+
Pin 2: Battery-
Note: 2.6V to 3.6V
3
3
1
2
J1 JP1 JP1
2
2
1
1
External Batter
y
Header On-Board Batter
y
External Batter
y
Factor
y
Preset
Pin 1: +12V
Pin 2: Ground
Pin 3: ENABLK
Pin 4: N.C.
Pin 5: +5V
CN8
5 1
BUS1-1 – BUS A & B
1
2 63 64
2
1 40 39
BUS1-2 – BUS C & D
2 10
CN4 LM1
Hard Disk Access LED (Red)
1
9 Power LED (Green)
Front View
©2001-2002 FabiaTech Corp.