FabiaTech Fanless Series User manual

FabiaTech Corporation
IPC Solution
Website: http://www.fabiatech.com
Email: [e-mail]
Small Cube System
Fanless Series
FX5327 User’s Manual
JAN 2019
Version: 1.2
Part Number: FX5327
i

Copyright
Copyright © 2016 FabiaTech Corporation, The content of this publication may not
be reproduced in any part or as a whole, transcribed, stored in a retrieval system,
translated into any language, or transcribed in any form or by any means,
electronic, mechanical, and magnetic… or otherwise without the prior written
permission of FabiaTech Corporation.
Disclaimer
FabiaTech makes no representation of warranties with respect to the contents of
this publication. In an effort to continuously improve the product and add features,
FabiaTech reserves the right to revise the publication or change specifications
contained in it from time to time without prior notice of any kind from time to time.
FabiaTech shall not be reliable for technical or editorial errors or omissions, which
may occur in this document. FabiaTech shall not be reliable for any indirect,
special, incidental or consequential damages resulting from the furnishing,
performance, or use of this document.
Trademarks
Trademarks, brand names and products names mentioned in this publication are
used for identification purpose only and are the properties of their respective
owners.
Technical Support
If you have problems or difficulties in using the system or setting up the relevant
devices, and software that are not explained in this manual, please contact our
service engineer for service, or send email to sup[email protected].
Returning Your Board for Service & Technical Support
If your board requires servicing, contact the dealer from whom you purchased the
product for service information. You can help assure efficient servicing of your
product by following these guidelines:
A list of your name, address, telephone, facsimile number, or email address
where you may be reached during the day
Description of you peripheral attachments
Description of your software (operating system, version, application
software, etc.) and BIOS configuration
Description of the symptoms (Extract wording any message)
For updated drivers, manuals, or product information, please visit us at
www.fabiatech.com.
ii

Table of Contents
FX5327 User’s Manual ...........................................................................................................i
Chapter 1 Introducing the FX5327 System ............................................................................... 1
Overview..................................................................................................................................1
Series Comparison Table.......................................................................................................2
Layout.......................................................................................................................................3
Specifications..........................................................................................................................4
Packing List..............................................................................................................................5
Chapter 2 Hardware Installation ............................................................................................... 7
Before Installation...................................................................................................................7
Removing Covers –Installing Hardware...........................................................8
I/O Peripheral Connectors ..............................................................................12
Connecting the DC Power and Power Button ............................................16
Power and HDD LED Indicator........................................................................16
Switch and Jumper Setting .............................................................................17
Chapter 3 BIOS Setup............................................................................................................... 21
Overview................................................................................................................................21
BIOS Functions ...................................................................................................22
Keyboard Convention.....................................................................................23
Main Setup ............................................................................................................................24
Advanced Setup..................................................................................................................25
ACPI settings......................................................................................................26
Hardware Monitor Configuration...................................................................27
F81216 Super IO Configuration.......................................................................28
Serial Port Console Redirection ......................................................................30
CPU Configuration............................................................................................36
PPM Configuration............................................................................................40
Thermal Configuration Parameters................................................................41
SATA Configuration...........................................................................................42
Network Stack Configuration..........................................................................43
CSM Configuration...........................................................................................44
USB Configuration.............................................................................................47
iii

Security Configuration .....................................................................................50
Realtek PCIe GBE Family Controller (MAC)..................................................51
Chipset...................................................................................................................................52
North Bridge.......................................................................................................53
South Bridge.......................................................................................................56
Security...................................................................................................................................60
Boot ........................................................................................................................................62
Save & Exit.............................................................................................................................64
Chapter 4 Software Installation ............................................................................................... 67
System Driver.........................................................................................................................67
WIN 7/8.1/10 -32/-64 Driver..............................................................................67
VGA Driver.............................................................................................................................68
WIN 7/8.1/10 -32/-64 Driver..............................................................................68
Audio Driver...........................................................................................................................68
WIN 7/8.1/10 X86/X64 Driver............................................................................68
LAN Driver (RTL 8111F)..........................................................................................................69
WIN 7 Driver X86/X64 Driver.............................................................................69
USB 3.0 Driver.........................................................................................................................69
WIN7 X86/X64 Driver .........................................................................................69
TXE Driver................................................................................................................................70
WIN7/8.1/10 X86/X64 Driver.............................................................................70
EFI BIOS Flash Utility...............................................................................................................71
Watchdog Timer...................................................................................................................72
Watchdog Timer Setting..................................................................................73
Watchdog Timer Enabled ...............................................................................74
Watchdog Timer Trigger ..................................................................................75
Watchdog Timer Disabled...............................................................................75
Digital I/O programming.....................................................................................................76
CANBUS..................................................................................................................................77
Defined Memory Mapping And Interrupt.....................................................77
Example Programming....................................................................................78
Chapter 5 Technical Reference .............................................................................................. 79
Technical Reference............................................................................................................79
iv

Physical and Environmental............................................................................79
Serial Ports..........................................................................................................80
Appendix................................................................................................................................... 84
Dimension..............................................................................................................................84
v

vi

FabiaTech Corporation
Chapter1IntroducingtheFX5327System
Overview
The FX5327 is an embedded system with Intel® Celeron® Braswell low-power CPU
module inside. This user’s manual provides information on the physical features,
installation, and BIOS setup of the FX5327.
Built to unleash the total potential of the Intel® Celeron® N3160 Quad-Core
Processor, Able to support 1.6 GHz CPU, this unit supports two 10/100/1000 Base –TX
LAN port, audio, four USB-2.0, one USB-2.0/3.0 ports, GPIO-2In/2Out digital I/O, PCIe
mini card socket, one SD/SATA/ CFAST socket, one So-DIMM socket supports up to
4GB DDR3L RAM, and VGA display.
Each FX5327 has two ports for I/O communications. One RS232/RS422/RS485 port
and one RS232/RS422/RS485/CAN port are available. The CAN (Controller Area
Network) is a serial bus system especially suited for networking "intelligent" I/O
devices as well as sensors and actuators within a machine or plant. Characterized
by its multi-master protocol, real-time capability, error correction, high noise
immunity, and the existence of many different silicon components, the CAN serial
bus system, originally developed by Bosch for use in automobiles, is increasingly
being used in industrial automation.
The FX5327 is perfect for ATM machines, KIOSK, point-of-sales/point-of- information,
gaming and infotainment, measurement technology, lotteries, and banking and
small Embedded Control. The unit is only 54 mm (W) X 104 mm (D) X145 mm (H).
1

FabiaTech Corporation
SeriesComparisonTable
Model FX5327
System Processor Intel ® Celeron ® N3160 1.6GHZ
(Braswell)
Memory
204 Pin-DIMM*1 DDR3L-1333 4GB (Max.)
One CFAST Socket
One SD Socket
Storage
One 2.5’ SATA HDD Connector
Display VGA
Multi I/O One RS232/RS422/RS485
and
One RS232/RS422/RS485 or CAN
(SJA1000)
USB 2.0 / 3.0 Four / One
Audio Ear-Phone
RJ45 LAN port
(10/100/1000 Mbps) Two Realtek RTL8111F
PCIe Mini Card Socket One
SIM Card Socket One
GPIO Two- In/Two-Out
Watchdog Timer Yes
Operating Temperature -20~+ 55℃(-4~131℉)
Dimensions (Unit: mm) 54(W) x 104 (D) X 145 (H)
2

FabiaTech Corporation
Layout
1
2
-
+
1
COM
DO
CAN
/
2
DI
12~40V
+
0
1
DC -
1
09~32V
DC IN
LAN1
LAN2
USB
HDD
EAR-PHONE
VGA
DC IN
ANTENNA
POWER
BUTTON
USB
COM1
COM2/CAN
DIGITAL I/O
3

FabiaTech Corporation
Specifications
Processor Board –
Intel ® Celeron ® Braswell N3160 Quad-Core Soc 1.6GHZ (Burst- 2.24GHz)
Low Power Processor with 4GB DDR3L-RAM
I/O Outlets –
Two 10/100/1000 base-TX Ethernet LAN port with RJ45
One VGA display connector with DB15 and one Audio connector for
Earphone-Out
Four USB (2.0) and One USB (3.0) ports
One RS-232/RS422/RS485 and one RS-232/RS422/RS485/CAN port with DB9
2-In and 2-Out Isolated Digital I/O with terminal block
One PCIe Mini card socket modules, especially for WLAN/GPRS module
One DC-In terminal block and power button
CAN BUS –
The CAN bus using the Philips SJA1000 controller, electrically compatible
with the PCA82C200 stand-alone CAN controller chip
• Full CAN-functionality 2.0 B
• Extended receive buffer (64 byte FIFO)
• 16 MHz CAN Control frequency
Storage Bay-
CFast Compact Flash socket for CFast Compact Flash modules
One SATA 2.5" hard disk space and One SD socket
Power requirement –
+9 ~ +32V DC, 2.1A maximum (1.1A typical) with DC 19V input
Dimensions -
54mm (W) x 104mm (D) X 145mm (H)
4

FabiaTech Corporation
PackingList
Upon receiving the package, verify the following things. Should any of the
mentioned happens, contact us for immediate service.
•Unpack and inspect the FX5327 package for possible damage that may
occur during the delivery process.
•Verify the accessories in the package according to the packing list and see
if there is anything missing or incorrect package is included.
•If the cable(s) you use to install the FX5327 is not supplied from us, please
make sure the specification of the cable(s) is compatible with the FX5327
system.
Note: after you install the FX5327, it is recommended that you keep the diskette or
CD that contains drivers and document files, and keep the document
copies, or unused cables in the carton for future use.
The following lists the accessories that may be included in your FX5327 package.
Some accessories are optional items that are only shipped upon order.
•One FX5327 embedded system.
•One pack of 2.5” HDD and mini-card installation with 6 fixed screws.
•One 2-pin apartable terminal block for power input.
•One 2*3-pin apartable terminal block for isolated digital I/O.
•One DIN Rail mounting kit with 2 screws.
•One compact disc includes software utility and manual.
Optional:
•One pack of half size mini PCIe module adapter kits.( P/N:0606010028G)
•FX5311K1 panel back mounting fixers and 2 screws (VESA 75*75 Only).
(P/N:0606010019G)
•FX5407K3 panel mounting fixers and 12 screws (50*50/75*75/100*100).
(P/N: 0606010038R)
5

FabiaTech Corporation
6

FabiaTech Corporation
Chapter2HardwareInstallation
This chapter introduces the system connectors & jumper settings, and guides you to
apply them for field application.
BeforeInstallation
Before you install the system, make sure you follow the following descriptions.
1. Before removing the cover, shut down the operation System and disconnect
power switch to off and unplug DC-In cable.
2. Install any connector, CFAST, Mini-Card, and hard disk is sure that the power is
disconnected or power switch to off from the system. If not, this may damage
the system.
3. The ESD (Electricity Static Discharge) may be created from human body that
touches the board. It may do damage to the board circuit.
7

FabiaTech Corporation
Removing Covers –Installing Hardware
If you are installing hardware option, you can remove the front and back cover.
The following figure will guide you how to install CFAST modules, SD Card, 2.5"
HDD inside and PCIe Mini card the FX5327 and how to install the FX5327 fixers.
(Please see the spots circled.)
¾a. Unscrew back cover
¾b. Installing Hard Disk, CFAST Compact Flash & SD Card
2. The SD socket supports up to 32GB SDHC (Class 6).
Note: 1. Use caution when handling the hard disk to prevent damage to SATA
connector as you inserted hard disk. Be careful with the orientation when
installing connectors.
8

FabiaTech Corporation
¾c. Installing Memory: So-DIMM Socket for DDR3L RAM Modules
You may extend additional memory to FX5327, See as following figure and rear
pictures.The So-DIMM socket supports 2GB to 4GB of DDR3L RAM modules.
¾d. Installing PCIe Mini Card Module –Daughter Board
You may extend additional PCIe mini card module and SIM card to FX5327.
Connect the antenna cable from backside antenna hole to GPRS module and
installing the SIM card to SIM socket. See as following figure.
Note: 1. When installing PCIe GPRS Mini card on FX5327 system these is need
the installing the SIM Card to daughter board of system.
2. The insert SIM card into the SIM card socket. Make sure that the SIM card
is properly inserted and that golden contact area on the card is facing
downwards.
9

FabiaTech Corporation
d1. Installing Half Size Mini PCIe module kit (Optional)
¾e. Installing the DIN-Rail fixers or universal fixers on FX5327
Please refer to the down side figure for installing the FX5327 with universal fixers.
e1. FX5327 Din-Rail
e2. FX5311K1 – Panel Back Mounting (VESA Mount 75*75)
10

FabiaTech Corporation
e3. FX5407K3 – Panel Mounting Kit (VESA Mount 50*50/75*75/100*100)
M4*P0.7
M3*P0.5
11

FabiaTech Corporation
I/O Peripheral Connectors
View from the back side, if you are connecting the monitor, LAN, COM, CAN,
Audio, Digital I/O and USB to the FX5327. See following figure and a side pictures.
1
2
-
+
1
COM
DO
CAN
/
2
DI
12~40V
+
0
1
DC -
1
09~32V
DC IN
LAN1
LAN2
USB
HDD
EAR-PHONE
VGA
DC IN
ANTENNA
POWER
BUTTON
USB
COM1
COM2/CAN
DIGITAL I/O
1. Connecting the VGA port
DB15 Signal
1 Red
2 Green
3 Blue
13 Hsync
14 Vsync
12 DDC Data
15 DDC Clock
5 & 10 Digital Ground
6,7,8 Analog Ground
Others Not Used
12

FabiaTech Corporation
2. Connecting the COM port
The COM1 and COM2 (DB9) are designed for multiple proposes, It’s can select RS-
232/422/485/CAN (The CAN port Only for COM2) by BIOS or jumper setting. The
following tables show the signal connections of these connectors.
DB9 RS-232 RS-422 RS-485
1 -DCD
6 -DSR
2 RXD RX- 485-
7 -RTS TX-
3 -TXD RX+ 485+
8 -CTS TX+
4 -DTR
9 -RI/5Vor 12V
5 Ground
Metal Case Ground
3. Connecting the CAN-BUS
The CANBUS is use COM2 (DB9) standard connector. The following tables show
the signal connections of this connector.
COM1 COM2
CAN DB-9
CANBUS Signal CANBUS Description
1 N.C -
6 N.C -
2 CAN-L Dominant Low
7 CAN-H Dominant High
3 CAN-Ground Isolated Ground
8 N.C -
4 N.C -
9 N.C -
5 Ground Digital Ground
Case Case Ground
1 6
5 9
Note: The CANBUS DB9-pin out conforms to the ISO 11898/2 standard specification.
13

FabiaTech Corporation
14
4. Connecting the LAN ports (LAN1&LAN2)
The RJ45 connector with 2 LED’s for LAN. The down side LED (orange) indicates
data is being accessed and the up side LED (green) indicates on-line status. (On
indicates on-line and off indicates off-line)
5. Connecting the USB Ports
The system supports a five port USB connector. Any USB device can be attached
to USB ports as plug-and-play function is supported. The left side port USB #1 can
support USB2.0/3.0, and right side USB #2 to USB #5 support USB 2.0.
6. Digital I/O Connector
The FX5327 provides 2-in and 2-out isolated digital I/O, output port is an open
collector, you will need connections external voltage of Digital (+) and digital (-)
connector.
Digital I/O
-
0
1
0
1
+
DO DI
DC IN
12~40V
RJ45 LAN1/2 RJ45 LAN1/2
1 MDI0+ 5 MDI2-
2 MDI0- 6 MDI1-
3 MDI1+ 7 MDI3+
4 MDI2+ 8 MDI3-
USB Signal
1 USBV
2 USBD- (V2.0)
3 USBD+(V2.0)
4 USBG
5 StdA_SSRX-(V3.0)
6 StdA_SSRX+(V3.0)
7 USBG (V3.0)
8 StdA_SSTX-(V3.0)
9 StdA_SSTX+(V3.0)
DI/O Signal Bit Location
IN-1 DGI1
IN-0 DGI0
OUT-1 DGO1
OUT-0 DGO0
+ Digital Voltage
- Digital Ground
Please refer to
Chapter 4-
Digital I/O -
Software
programming
example
RJ45 connector
8
1
Note: Digital inputs accept DC12~40V Signal with isolated input. Digital outputs
are active-low open collector output, and can drive up to 60V/400mA
maximum.
D I/O
(Front View)
4
5
91
41
USB 3.0
USB 2.0