FabiaTech FB2730 Series User manual

Version 1.0 FB2730 Series User’s Quick Reference Page 1/3
www.fabiatech.com ©2015 FabiaTech Corporation
1. Brief
The FB2730x is an all-in-one, 3.5" disk size with low power Intel Bay Trail-I CPU on-board. This user’s
quick setting provides the jumper settings, connector location, and their pin assignment.
2. Board Placement
J6 CN9 CN8 CN10 J5 CN7
CN4 J1
J9
J7
CN17
J4
SW2 CN3CN11CN15CN16CN14CN13
BZ1
BT1
CN2
CN1
JP2
U1
D3D5
JP1
J3
JP3
(Component Side)
DIMM1
CN5
(Solder Side)
3. Packing List
A. Standard Items
1 FX2730x embedded borad.
1 6-pin DC power cable for power input.
1 8-pin SATA signal cable for SATA devices.
1 10-pin dual port USB adapter cable.
1 compact disc includes software utilities and manuals.
B. Optional Items
# Half size mini PCIe module adapter kit (AK1006, 1 piece of metal with 2 screws, P/N:
0606010028G)
# Audio/USB adapter kit (P/N: 0103020022G-21, 1 FB4706 board with 2 cables)
# Serial port adapter cable (P/N: 7001000100R, 10-pins JST to DB9)
4. Features
On-Board Intel® Bay Trail-I E3845 (Quad Core 1.91GHz, 2MB cache, FSB 1333MHz, 10 Watts)
low power processor. E3825 (Dual Core 1.33GHz, 1MB cache, FSB 1067MHz, 6 Watts) is optional.
1 SoDIMM socket for DDR3L modules. (8GB Maximum)
Two 10/100/1000 base-TX Ethernet ports.
4 USB ports (including 1 USB 3.0), 3 RS-232, and 1 RS-232/422/485 serial ports.
1 VGA, 1 eDP, and 1 Audio connectors.
1 SATA, 1 CFast socket, and 1 mini PCIe socket with 1 SIM sockets.
1 DC-In power connector and 2 LEDs indicate power, HDD/CFast access.
1 PCIe expansion bus. (The riser card is needed and optional item)
+5V DC, 4.63A maximum (2.94A typical) with fully I/O loads.
Dimensions: 144.8mm (L) x 102.1mm (D) (PCB only).
5. Connectors and Jumpers List
Name Function Name Function
CN1 Mini PCIe Socket J1 AMR Connector (mIDC 2*6-pin)
CN2 SIM Socket J3 LPC Connector (J2*5 header)
CN3 VGA Connector (15-pin D-sub) J4 Reserved for on-board CPLD
CN4 SATA Connector J5 Power Connector (6-pin JST)
CN5 CFast Socket (PCB Solder Side) J6 Power Button Header (J1*2)
CN7 DDI Panel Connector (40-pin DF-13) J7 USB #1 / #3 Connector (J2*5)
CN8 Serial Port 3 Connector (IDC 2*5-pin) J8 Reserved
CN9 Serial Port 4 Connector (IDC 2*5-pin) J9 Clear CMOS RAM Header (J1*2)
CN10 Serial Port 2 Connector (IDC 2*5-pin) JP1 mPCIe Aux. Power Select (J1*3)
CN11 Serial Port 1 Connector (9-pin D-Sub) JP2 RS-485 Terminator Select (J1*3)
CN13 USB #2 Connector JP3 USB #3 Signal Select (J1*3)
CN14 USB #0 Connector (USB 3.0) BZ1 On-Board Buzzer
CN15 LAN #1 Connector (RJ-45 w/LEDs) D3 SATA/CFast Access LED (Red)
CN16 LAN #2 Connector (RJ-45 w/LEDs) D5 Power LED (Green)
CN17 PCIe Expansion Bus (x1) DIMM1 DDR3L SoDIMM Socket
SW2 Reset Switch

Version 1.0 FB2730 Series User’s Quick Reference Page 2/3
www.fabiatech.com ©2015 FabiaTech Corporation
6. Connectors and Their Relative Jumpers
A. Power Connector (J5) and Power Button Header (J6)
C. VGA Connector (CN3)
D. On-board LED Indicators (D3, D5) and Clear CMOS RAM (J9)
E. USB Connectors (CN13, CN14, J7, and JP3)
F. SoDIMM Socket (DIMM1)
DIMM1 (Located on the solder side) supports 204-pin, 1.35V, and DDR3L DRAM modules with size
of 4GB and 8GB.
G. LAN Connectors and LED Indicators (CN15 and CN16)
CN15 and CN16 both are standard RJ45 connector with 2 LEDs. The orange LED indicates data is
accessing and the green LED indicates on-line status.
H. Serial Port Connectors and Select Jumpers (CN8, CN9, CN10, CN11, and JP2)
1 8
CN15 &
CN16
(Front View)
CN15/CN16 10/100 Giga CN15/CN16 10/100 Giga
1 TPTX+ MDI0+ 5 FBG1 MDI2-
2 TPTX- MDI0- 6 TPRX- MDI1-
3 TPRX+ MDI1+ 7 FBG2 MDI3+
4 FBG1 MDI2+ 8 FBG2 MDI3-
J9
D5
2
1
D3: HDD/CFast Access LED
Close J9 for around 3 seconds
to clear CMOS RAM
D3
D5: Power
LED
Pin 1: Red
Pin 2: Green
Pin 3: Blue
Pin 13: Hsync
Pin 14: Vsync
Pin 12: DDC Data
Pin 15: DDC Clock
Pin 5 & 10: Digital Ground
Pin 6,7,8: Analog Ground
Others:
Not Used
1
5
CN3
(15-pin D-sub)
11
15
Pin 1: Ground
Pin 2: +5V
Pin 3: +5V
Pin 4: Ground
Pin 5: Ground
Pin 6: +12V (Connects to CN17 only)
J5
6
1
J6
1
Connects J6 to a soft-start
power button.
2
CN11 (9-pin D-sub)
-and-
Serial port adapter cables of
CN10, CN8, and CN9
Functional connector, header,
and jumper of serial ports
Serial
Port 1
Serial
Port 2
Serial
Port 3
Serial
Port 4
Remark
RS-232 Signals CN11 CN10 CN8 CN9
RS-422 Signals CN11 - - -
RS-485 Signals CN11, JP2 - - -
232/422/485 Mode Select CMOS Setup Utility - - -
1
5
9 6
CN11 RS-232 RS-422 RS-485 CN10/CN8/CN9
9-pin
D-sub
Signals
1 -DCD1 - 1 1 -DCD2/3/4
6 -DSR2 - 2 6 -DSR2/3/4
2 RXD1 RX- 485- 3 2 RXD2/3/4
7 -RTS1 TX- - 4 7 -RTS2/3/4
3 TXD1 RX+ 485+ 5 3 TXD2/3/4
8 -CTS1 TX+ - 6 8 -CTS2/3/4
4 -DTR1 - 7 4 -DTR2/3/4
9 -RI1 - 8 9 -RI2/3/4
5 Ground1 9 5 Ground2/3/4
Metal Case Ground (C.G.) 10 Metal C. G.
JP2
Terminator Off
3
2
2
1
3
1
JP2
Terminator ON
Factory Preset
9
J7 Signal J7 Signal
1 USBV1 2 Case Ground
3 USBD1- 4 USBG3
5 USBD1+ 6 USBD3+
7 USBG1 8 USBD3-
9 Case Ground 10 USBV3
J7
1
0
1 2
CN13 CN14 (V3.0)
JP3
J7
3
2
2
1
3
1
JP3
mPCIe Socket
Factory Preset
Note that USB Port #3 is shared with USB signals on
mPCIe socket. Use JP3 to select the correct setting
that you intend to use.
There are 4 connectors and 1 jumper that served for on-board 4 serial ports. The following
table and figure list the combination and pin definition of them:

Version 1.0 FB2730 Series User’s Quick Reference Page 3/3
www.fabiatech.com ©2015 FabiaTech Corporation
I. Audio (AMR) Connector (J1: 12-pin 2.0mm IDC) and Expand USB Connectors on FB4706
Adapter Board
J1 is a 12-pin 2.0mm IDC connector with AMR signals for Audio I/O. Use the included Audio cable
and FB4706 adapter board for your Audio applications. CN5, CN6, and CN4 connectors on FB4706
are 2-way Line-In, mono Microphone input, and 2-way Line-Out respectively. The following figure
shows CN19 and Audio connectors on FB4706 board:
Use the included expand USB cable connects to J7 of FB4706 (V2.1 and later) for USB #3 and
USB #4 signals (CN1 and CN3 on FB4706). Please refer the following FB4706 Board Layout:
CN4 CN6 CN5
CN1 CN3
CN2
CN7
JP1
FB4706 VER:2.1
J. Mini PCIe Aux. Power Source Select (JP1)
K. DDI Connector (CN7)
L. LPC Connector (J3)
J1
2
11 1
1
2
Line-Out Line-In Mic-In
J1 Signal J1 Signal
1 BITCLK 2 N. C.
3 +5V 4 SYNC
5 Ground 6 Ground
7 +3.3V 8 ACRST#
9 SDOUT 10 SDIN2
11 SDIN0 12 SDIN1
Audio Connectors on FB4706
Adapter Board
End of Document
9
J3 Signal J3 Signal
1 +3.3V 2 FRAME#
3 N. C. 4 LPC_AD0
5 RESET# 6 LPC_AD1
7 CLK 8 LPC_AD2
9 Ground 10 LPC_AD3
J3
1
0
1
2
JP1
+
3.3
V
3
2
2
1
3
1
JP1
+1.8V
Factory Preset
Note: If any question when connecting FB2730 with DDI panels, you could contact technical
support division of FabiaTech Corporation.
CN7 Signal CN7 Signal CN7 Signal CN7 Signal
1 +3.3V 21 TX1- 2 +3.3V 22 N. C.
3 +3.3V 23 TX1+ 4 +3.3V 24 BKLT_EN
5 +3.3V 25 Ground 6 N. C. 26 BKLT_CTL
7 Ground 27 TX0- 8 N. C. 28 Ground
9 TX3- 29 TX0+ 10 N. C. 30 BKLT_VCC
11 TX3+ 31 Ground 12 SMB_CLK 32 BKLT_VCC
13 Ground 33 AUX+ 14 SMB_DAT 34 N. C.
15 TX2- 35 AUX- 16 N. C. 36 N. C.
17 TX2+ 37 Ground 18 N. C. 38 +5VS
19 Ground 39 EMP_HDP 20 +3.3VS 40 +3.3VS
Connects to J1 of FB2730
for Audio functions
Connects to J7 of FB2730 for
USB #1 & USB #3