fantastic furniture Montana User manual

Version 1.0
Montana
fantasticfurniture.com.au
Double Bed

fantasticfurniture.com.au Page 2Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!

Assembly checklist
Useful information
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.
Page 3
fantasticfurniture.com.au

What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Headboard
(P1)
Side Rail
(P6)
Side Rail
(P6) Footboard
(P2)
Centre Rail
(P7)
Support leg
(P8)
Leg(P3)
Headboard and Footboard
Timber Cross Rail
(P5)
Wood Footboard
(P4)
Leg(P3)
Headboard and Footboard
Leg Support
Footboard (P2) ; 4 x Headboard and Footboard Legs (P3) ; 2 x Wood Footboard Leg
Headboard (P1) ; Slats (P11)
Parts list
Box 1 :
Box 2 :
Supports (P4) ; Timber Cross Rail (P5) ; 2 x Side Rails (P6) ; Center Rail (P7) ; 2 x Support
Legs (P8) ; End Connectors (P9) ; Centre Connectors (P10) ; Hardware Pack.
24 x End Connectors (P9) 12 x Centre Connectors (P10)
24 x Slats (P11)
Hardware pack
fantasticfurniture.com.au Page 4
Support leg
(P8)
(H1) (H2) (H5)(H3) (H4)
1 x Felt Pad
(H6)
10 x Spring Washer
(H8)(H7)
8 x Small Bolts 1 x Allen Key 14 x Medium Bolts 20 x Washers 6 x Screws
6 x Large Bolts

Step 2
(P1)
(P3)
(H4)
(H3)
(H2)
(P2)
(P4)
(P3)
(H4)
(H3)
(H2)
Attach 4 x legs (P3) to the bottom of headboard (P1) and wood footboard legs supports
(P4) with 8 x medium bolts (H3) and 8 x washers (H4) by using allen key (H2).
fantasticfurniture.com.au Page 5
You will need
Allen Key
(H2)
8 x Washers
(H4)
8 x Medium Bolts
(H3)
You will need
(H7)
6 x Washers M8
(H4)
Allen Key
(H2)
6 x Spring Washer
(H8)
4 x Screws
(H5)
Phillips head
Screwdriver
(not provided)
(P2)
(P4)
(P4)
(P4)
(H4)
(H8)
(H7)
(H2)
(H5)
Step 1
Attention:
Attach 2 x footboard leg support woods (P4) to the footboard (P2) with 6 x Large Bolts (H7),
4 x Screws (H5) by using s phillips head screwdriver (not provided).
6 x washers (H4) and 6 x spring washers (H8) by using allen key (H2). Then screw the
6 x Large Bolts

Step 3
You will need
(H1) (H2)
Allen Key
(P1)
(P6)
(P6)
(P2)
(H1)
(H2)
Install 8 x bolts (H1) to the brackets of the headboard (P1) and footboard (P2) by using
allen key (H2) as shown, do not tighten the bolts and keep them 8mm loose. Then attach
side rails (P6) to headboard (P1) and footboard (P2) by slotting the bracket on the side rails (P6)
over the bolt as shown. Please do not tighten bolts until step 7.
fantasticfurniture.com.au Page 6
8 x Small Bolts

(H3)
Step 4
(H2)
(H4) (P7)
(P8)
Attach 2 x support legs (P8) to the centre rail (P7) with 2 x bolts (H3) and 2 x washers (H4)
by using allen key (H2).
fantasticfurniture.com.au Page 7
(H4)
4 x
(H8)
Spring Washer
You will need
4 x Washers
(H4)
(H3)
(H2)
Allen Key
Step 5
(H8)
(H3)
(H2)
(P7)
(P1)
(P7)
(P6)
(P6)
(P2)
Adjust to be 10mm gap from floor
to the bottom of support legs.
Slot the centre rail (P7) into the headboard (P1) and footboard (P2).
Rotate 4 x bolts (H3) and 4 x washers (H4) and 4 x spring washers (H8) to the headboard (P1)
and footboard (P2) by using allen key (H2). Please do not tighten bolts until step 7.
You will need
2 x Washers
(H4)
2 x Medium Bolts
(H3)
Allen Key
(H2)
4 x Medium Bolts

You will need
24 x End
Connectors
(P9)
12 x Centre
Connectors
(P10)
24 x Slats
(P11)
Step 6
1
(P9) (P10) (P9)
Push 2 end connectors (P9), 2 pcs slats (P11)
and a centre connector (P10) together.
2
3
Insert the full slat into the side rail and centre rail one by one.
fantasticfurniture.com.au Page 8
Sometimes it makes it easier to line up the
hole if you press down in the middle of the
slat to flatten it out.
(P11) (P11)

4
Repeat for every bed slat until finished.
fantasticfurniture.com.au Page 9
Step 7
You will need
2 x Screws
(H5)
Phillips head
Screwdriver
(H2)
Allen Key
1 x Felt Pad
(H6)
(P1)
(P6) (P2)
(H2)
(H5)
(P5)
(P5)
(H6)
(P7)
Make sure screws
are fully tightened.
Make sure the inner space is square.
Attach the felt pad (H6) to the centre of centre rail (P7).
Then attach the timber cross rail (P5) to the centre of side rails (P6) by using 2 x screws (H5).
Now tighten all the bolts on the centre rail (P7) and tighten bolts on the headboard (P1)
and footboard (P2).

Step 8
fantasticfurniture.com.au Page 10
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.