fantastic furniture Sonoma Clothes Rack 2 Drawer User manual

fantasticfurniture.com.au
Sonoma
Clothes Rack 2 Drawer
Version 1.0

Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
fantasticfurniture.com.au
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Weight Limit: 20kgs per shelf
Warning: Ensure the wall strap is
attached to avoid serious injury.
To a void any serious of fatal injury, a wall strap has been provided with
this product to prevent topping. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.

fantasticfurniture.com.au Page 3
Read through the instructions
carefully before you begin.
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screwsuntil the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a so t surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
components please visit our website Help Centre for further assistance.
Assembly Checklist
!Please see page 2for any safety requirements or weight restrictions.
Useful information

Page 4
fantasticfurniture.com.au
What You Need
to assemble the product
Hardware Pack :
(H2) (H3) (H4)
5 x Screws 22 x Screws 1 x Nut
( H15)
Feet
(H1)
1 x Wall Strap 1 x Wall Strap
Screw
2 x Washers
(H16)
(H17)
(H18)
Lower Left Frame
Box 1:
Hanging Rail
(P1)
(P3)
(P4)
(P9)
(P10)
(P11)
(P12)
(P13)
(P14)
(P15)
(P17)
(P16)
(P19)
(P5)
(P6)
(P7)
(P8)
(P2)
(P2)
(P14)
Top Left Frame
Left Side Panel
Base Panel
Top Panel
DrawerTop Panel
Back Panel
Right Side Panel
Drawer Front
Drawer Front
(P18)
(H5)
18 x Cam Nuts
(H6)
18 x Cam Bolts
(H7)
8 x Dowels
22 x Nails
(H8) Tracks
(H9)
(H10) Tracks
(H11)
(H12)
4 x Adjustable
28 x Screws 12 x Screws
(H13) (H14)
Other tools you need
Phillips Head screwdriver;Hammer
1 x Allen Key
Top Panel (P1)
2 x Base Rails (P2)
Top Left Frame (P3)
Lower Left Frame (P4)
Top Right Frame (P5)
Lower Right Frame (P6)
2 x Back Supports (P7)
Hanging Rail (P8)
Drawer Top Panel (P9)
Base Panel (P10)
Left Side Panel (P11)
Right Side Panel (P12)
Back Panel (P13)
2 x Drawer Left Side Panels (P15)
2 x Drawer Right Side Panels (P16)
2 x Drawer Back Panels (P17)
2 x Drawer Bottom Panels (P18)
2 x Drawer Support Panels (P19)
2 x Drawer Fronts (P14)
Base Rails
Lower Right Frame
Top Right Frame
Back Support
2 x CL Runner 2 x DL Runners 2 x CR Runner 2 x DR Runners
1 x Wrench
(H19)

tightening with the Allen Key (H15).
Page 5
fantasticfurniture.com.au
Step 1
Step 2
You will need
4 x Adustable
Feet (H1) (H3)
4 x Screws
(H15)
(P5)
(H1)
(P3)
(P4)
(P3)
(P4)
(P5)
(P6)
(P5)
(P6) (H3)
(H15)
(H3)
(H1)
(H1)
(H1)
(P6)
(P3)
(P4)
Allen Key
(H15)
Attach Top & Lower Left Frames (P3&P4) with 2 x Screws (H3) by
Repeat steps for Top & Lower Right Frames (P5&P6). Secure 4 x Adjustable Feet (H1)to
the bottom of Lower Left & Right Frames (P4&P6) as shown.
You will need
(H15)
(H15)
(H3)
8 x Screws
(H15)
(P1)
(P3)
(P3)
(P4)
(P5)
(P6)
(P2)
(P2)
(P1)
(P2)
(P2)
(P4)
(P4)
(P4)
(P2)
(P4)
(P2)
(H3)
(H3)
(H15)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
Allen Key
(H3)
Attach Top & Lower Left Frames (P3&P4) and
Top & Lower Right Frames (P5&P6) to Top
Panel (P1) and Base Rails (P2x2) with 8 x Screws
(H3) as shown by tightening with the Allen Key (H15).
(H3)
(H3)

Page 6
fantasticfurniture.com.au
You will need
Step 4
(P7)
(P7)
1 x Nut
(H4)
(H15)
(H2)
(H2)
1 x Screw
( H15)
(H2)
(H4)
(P7)
(P7)
(H4)
Allen Key
(P8)
(H15)
(H3)
(P5)
(H15)
(H2)
(P3)
(P5)
(P8)
(P3)
(P7)
(P7)
(P7)
(H3)
(H3) (H2)
(H2)
(H2)
You will need
(H2)
4 x Screws
(H15)
(H3)
2 x Screws
Allen Key
Secure Back Supports (P7x2) together as shown with 1 x Nut (H4) and 1 x Screw (H2) by
Attach Back Supports (P7x2) to Top Left & Right
Frames (P3&P5) as shown with 4 x Screws (H2) by tightening
with the Allen Key (H15).
Secure Hanging Rail (P8) to Top Left & Right Frames (P3&P5)
as shown with 2 x Screws (H3) by tightening with the Allen Key (H15).
Step 3
1 x Wrench
(H19)
tightening with the Allen Key (H15) and Wrench (H19).
(H19)
(H19)

(H13)
(P11)
Page 7
fantasticfurniture.com.au
(P12)
You will need
16 x Screws
(H13) (H11)
(H11)
(H13)
(H7)
(H7)
(H7)
(H7)
(H5)
(H5)
(H5) (H13)
(H11)
(H5)
2 x CR Runner
Tracks (H11)
You will need
(H5)
4 x Cam Nuts
(H7)
4 x Dowels
2 x CL Runner
Tracks (H9)
8 x Screws
(H13) (H9)
(H9)
(H13)
(H13)
(H5)
(H5)
(H9)
(H5)
(H13)
(H13)
(H5)
4 x Cam Nuts
(H7)
4 x Dowels
(H5)
(H5)
(H7)
(H7)
(H7)
(H7)
(H13)
(H13)
(P11)
(H5)
(H13)
(H13)
(H13)
Insert 4 x Dowels (H7) and 4 x Cam Nuts (H5) into Left Side Panel (P11) as shown.
Attach 2 x CL Runner Tracks (H9) to Left Side Panel (P11) with 8 x Screws (H13) as shown
by tightening with the Phillips Head Screwdriver.
Attach 2 x CR Runner Tracks (H11) to Right Side Panel (P12) with 8 x Screws (H13) as shown
by tightening with the Phillips Head Screwdriver.
Insert 4 x Dowels (H7) and 4 x Cam Nuts (H5) into Right Side Panel (P12) as shown.
Step 5
Step 6
Phillps head
Screwdriver
Phillps head
Screwdriver

Page 8
Step 7
Step 8
You will need
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
overthe bolt.
(H6)
(H5)
(H7)
(H7)
(H7) (H7)
(H7)
(H5)
(H7)
(H7)
(P9)
(P12)
(P11)
(P10)
You will need
(H6)
8 x Cam Bolts
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(P9)
(P10)
Attach 8 x Cam Bolts (H6) to Drawer Top Panel (P9) and Base Panel (P10) as shown by
tightening with the Phillips Head Screwdriver.
Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts. Secure the
Drawer Top Panel (P9) and Base Panel (P10) to Left & Right Side Panels (P11&P12) as
shown by tightening 8 x Cam Nuts (H5) with the Phillips Head Screwdriver.
fantasticfurniture.com.au
Phillps head
Screwdriver
Phillps head
Screwdriver

Page 9
fantasticfurniture.com.au
(P11)
(H9)
You will need
Step 10
(P10)
(P13)
(P6)
(H8)
5mm
2mm
2mm
5mm
(H8)
(H8)
(H8)
(P13)
Hammer
20 x Nails
(H8)
(P4)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)
(H8)(H8)
You will need
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(P10)
(P9)
(P6)
(H15)
(H3)
6 x Screws
(P12)
Allen Key
(P4)
(H15)
(H15)
(P11)
(P4)
(P6)
(P4)
Gently place the partially assembled drawer unit into the
shelving frame as shown. Secure the Base Panel (P10) to
Lower Left & Right Frames (P4&P6) and Base Rails (P2x2)
with 6 x Screws (H3) by tightening with the Allen Key (H15).
Secure Back Panel (P13) to the back of the partially assembled drawer unit as shown
with 20 x Nails, approximately 5mm from the edge, using the Hammer. Ensure the
Back Panel is sitting square in the unit before securing, with about 2mm around each
edge.
Step 9

Page10
fantasticfurniture.com.au
Step 11
You will need
Step 12
(H14)
12 x Screws
(P15)
(P16)
(P17)
(P19)
(H14)
(H14)
(H14)
(H14)
(P16)
(P17)
x 2
You will need
(H6)
10 x Cam Bolts
(H6)
(H6)
(H6)
(H6)
(H6)
(H6)
(P14)
x 2
(P14)
Secure 5 x Cam Bolts (H6) to Drawer Front (P14) by tightening with the Phillips
Head Screwdriver.
Repeat steps for the second Drawer.
Secure Left & Right Drawer Sides (P15&P16) to Back Panel (P17) with 4 x Screws (H14) by
tightening with the Phillips Head Screwdriver. Attach Drawer Support Panel (P19) to Back
Panel (P17) with 2 x Screws (H14) by tightening with the Phillips Head Screwdriver.
Repeat steps for the second Drawer.
Phillps head
Screwdriver
Phillps head
Screwdriver

fantasticfurniture.com.au Page 11
You will need
(H5)
10 x Cam Nuts
10 x Cam Nuts
x 2
(P14)
(P18)
(P16)
(P15)
(P19)
(H5)
(H5)
(H5)
(H5)
(P14)
Raw Side
(P15)
(P16)
(P19)
(P17)
(P18)
x 2
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
Repeat steps for the second Drawer.
Slide Drawer Base (P18) into the grooves of Left & Right Drawer Sides (P15&P16) and
Back Panel (P17).
Insert 5 x Cam Nuts (H5) into Left & Right Drawer Sides (P15&P16) and Drawer Support Panel (P19) as
shown. Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts. Secure the
Repeat steps for the second Drawer.
Step 14
Step 13
Phillps head
screwdriver
Drawer Front (P14) toDrawer Lef t & Right Side Panels (P15&P16) and Drawer Support Panel (P19) as
shown by tightening 5 x Cam Nuts (H15) with the Phillips Head Screwdriver.

Page 12
fantasticfurniture.com.au
You will need
(H10)
12 x Screws
(H13)
Phillips head
screwdriver
2 x DL Runners x 2
(H10)
(H10)
(H12)
(P16)
(P15)
(P15)
(H12)
2 x DR Runners
(H13)
(H13)
(H13)
(H13)
(H13)
(H13)
(H13)
Secure 1 x DL Runner (H10) to Drawer Left Side Panel (P15) and 1 x DR Runner (H12) to
Drawer Right Side Panel (P16) as shown with 6 x Screws (H13) by tightening with the
Phillips Head Screwdriver.
Repeat steps for the second Drawer.
WARNING:ENSURETHE
WALLSTRAPIS
ATTACHEDTOAVOIDSERIOUSINJURY.
Toavoidany
seriousorfatalinjury,thisproducthasbeen
fittedwithawallstraptopreventtoppling.Westrongly
recommendthatthisproductispermanentlyfixedtothe
wallorothersuitablesurface.Fixingdevicesarenot
includedsincedierentsurfacematerialsrequire
dierentattachments.Pleaseseekprofessionaladvice
ifyouareindoubtofwhatfixingdevicetouse.
COUNTRYOFORIGIN
CHINA
IMPORTEDBY
FHLDistributionCentrePtyLtd
71SevilleStreet
FAIRFIELDEAST
NSW2165
AUSTRALIA
PO#:ABC123
(P1)
You will need (H17)
(H18) (H16)
1 x Wall Strap 1 x Wall Strap
Screw
1 x Washer
(H16) (H17)
(H18)
Step 16
Carefully insert the assembled drawers into the unit by gently guiding the runners
into the tracks.
Attach the Wall Strap (H16) to Top Panel (P1) with 1 x Washer (H18) and 1 x Wall Strap
Screw (H17) by tightening with the Phillips Head Screwdriver.
Step 15
Phillps head
Screwdriver

Page13
fantasticfurniture.com.au
Screws and wall plugs are not
provided please use appropriate
fixtures for your wall.
Seek advice from a qualified trades person
on how to attach this to your specific wall.
1 x Washer
(H18)
(H18)
We strongly suggest using the wall strap
to prevent this unit from toppling.
Move furniture to its final position,
firmly attached and a snug fit.
then connect the end of Wall
(H13)
Strap (H16) to the wall.Make sure it is
(H16)
WARNING:ENSURETHEWALLSTRAPIS
ATTACHEDTOAVOIDSERIOUSINJURY.
Toavoidanyseriousorfatalinjury,thisproducthasbeen
fittedwithawallstraptopreventtoppling.Westrongly
recommendthatthisproductispermanentlyfixedtothe
wallorothersuitablesurface.Fixing devices arenot
includedsincedierentsurfacematerialsrequire
di erentattachments.Pleaseseekprofessionaladvice
ifyouareindoubt of whatfixing devicetouse.
COUNTRYOFORIGIN
CHINA
IMPORTEDBY
FHLDistributionCentrePtyLtd
71SevilleStreet
FAIRFIELDEAST
NSW2165
AUSTRALIA
PO#:ABC123
(H16)
WARNING:ENSURETHEWALLSTRAPIS
ATTACHEDTOAVOIDSERIOUSINJURY.
Toavoidanyseriousorfatalinjury,thisproducthasbeen
fittedwithawallstraptopreventtoppling.Westrongly
recommendthatthisproductispermanentlyfixedto the
wallorother suitable surface. Fixing devices arenot
includedsincedierentsurfacematerialsrequire
di erentattachments.Pleaseseekprofessionaladvice
ifyouareindoubtofwhatfixingdevicetouse.
COUNTRYOFORIGIN
CHINA
IMPORTEDBY
FHLDistributionCentrePtyLtd
71SevilleStreet
FAIRFIELDEAST
NSW2165
AUSTRALIA
PO#:ABC123
You will need
Step 17
Job Complete!
In the interest of our environment
packaging thoughtfully.
please dispose of all
WARNING:ENSURETHE WALL STRAPIS
ATTACHEDTOAVOIDSERIOUSINJURY.
T
oavoidanyseriousorfatal injury,thisproducthasbeen
fittedwithawallstraptopreventtoppling.Westrongly
recommendthatthisproductispermanentlyfixed tothe
wallor other suitablesurface.Fixing devicesare not
includedsincedierent surfacematerialsrequire
di erentattachments.Pleaseseekprofessionaladvice
ifyouarein doubt ofwhatfixing devicetouse.
COUNTRYOFORIGIN
CHINA
IMPORTEDBY
FHLDistributionCentrePtyLtd
71SevilleStreet
FAIRFIELDEAST
NSW2165
AUSTRALIA
PO#:ABC123