fantastic furniture Nova Mid Sleeper Desk Lowboy White User manual

fantasticfurniture.com.au
Version 1.1
Nova
Mid Sleeper Desk Lowboy White
1.
2.
3.

Page 2
Looks like you’ve found
your Fantastic!
We’re
thrilled
you’ve chosen Fantastic Furniture
to help create a home you’ll love
fantasticfurniture.com.au
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Helpful bunk bed safety tips
Bunk beds should be checked periodically to ensure that the guardrail, ladder and other
components are secure and in the correct position and all connectors are tight.
We recommend that children under the age of nine (9) do not use the upper bunk. Children
should be discouraged from playing on the bunk bed.
No more than one occupant should use the upper bunk at any time (unless otherwise stated).
Bunk beds should be placed a minimum of 2 metres away from any ceiling fans to prevent any
injury to the upper bunk occupant.
Recommended weight capacity : 10Kg/Shelf
10Kg/Drawer

fantasticfurniture.com.au Page 3
Read through the instructions
carefully before you begin.
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screwsuntil the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a so t surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
components please visit our website Help Centre for further assistance.
Assembly checklist
!Please see page 2 for any safety requirements or weight restrictions.
Useful information

Page 4
fantasticfurniture.com.au
What You Need
to assemble the product
Other tools you need
Phillips Head screwdriver;
Hammer
Box 1:
Headboard (P1)
Footboard (P2)
4 x Bed Support Bar (P7)
Front Support Panel (P9)
2 x Frame Support Panel (P10)
Front Support Panel (P11)
Ladder Left Panel (P12)
Ladder Right Panel (P13)
Ladder Top Panel (P14)
Ladder Bottom Panel (P15)
2 x Ladder Support Bar (P16)
Box 4:
Top Panel (P17)
Base Panel (P18)
Side Panel (L) (P19)
Side Panel (R) (P20)
Rear Support Panel (P21)
Front Support Top Panel (P22)
2 x Front Support Panel (P23)
Back Panel (P24)
3 x Drawer Front Panel (P25)
3 x Drawer Side Panel (L) (P26)
3 x Drawer Side Panel (R) (P27)
3 x Drawer Back Panel (P28)
3 x Drawer Bottom Panel (P29)
3 x Drawer Support Panel (P30)
Support Bar (P47)
Box 5:
Drawer Support Panel (P30)
Desk Top Panel (P31)
Desk Side Panel (P32)
Desk Back Panel (P33)
Support Panel (P34)
Shelf Rear Panel (P35)
Shelf Middle Panel (P36)
Shelf Front Panel (P37)
2 x Shelf Panel (P38)
Shelf Back Panel (P39)
Shelf Base Panel (P40)
Drawer Front Panel (P41)
Drawer Side Panel (L) (P42)
Drawer Side Panel (R) (P43)
Drawer Back Panel (P44)
Drawer Bottom Panel (P45)
Support Bar (P46)
(P17)
(P19)
(P20)
(P21)
(P24)
(P23)
(P23)
(P26)
(P28)
(P27)
(P30)
(P47)
(P18) (P29)
(P25)
(P25)
(P35)
Desk Top Panel
(P31)
(P33)
(P32)
(P34)
(P46)
(P36)
(P37)
(P39)
(P38)
(P40)
(P41)
(P42)
(P43)
(P44)
(P45)
(P30)
(P1)
(P8)
Box 2:
Rear Side Rail (P4)
Rear Side Bottom Rail (P5)
Box 3:
2 x Bed Bottom Panel (P3)
Front Side Rail (P6)
2 x Bed Base Panel (P8)
(P4)
(P2)
(P3)
(P10)
(P10)
(P9)
(P12)
(P13)
(P11)
(P14)
(P15)
(P7)
(P7)
(P6)
(P5)
(P7)
(P16)
(P7)
(P3)
Rear Side Rail
Rear Side Bottom Rail
Bed Bottom Panel
Bed Bottom
Panel
Front Side Rail Bed Base Panel
Headboard
Footboard
Bed Support Bar
Bed Support Bar
Bed Support Bar
Bed Support Bar
Front Support Panel
Frame Support Panel
Frame Support Panel
Front Support Panel
Ladder Left Panel
Ladder Right Panel
Ladder Top Panel
Ladder Bottom Panel
Ladder Support Bar
Top Panel
Base Panel
Side Panel (L)
Side Panel (R)
Rear Support Panel
Front Support Panel
Front Support Panel
Back Panel
Drawer Front Panel
Drawer Front Panel
Drawer Side Panel (L)
Drawer Side Panel (R)
Drawer Back Panel
Drawer Bottom Panel
Drawer Support Panel
Support Bar
Support Bar
Desk Side Panel
Desk Back Panel Support Panel
Shelf Rear Panel
Shelf Middle Panel
Shelf Front Panel
Shelf Panel
(P38)
Shelf Panel
Shelf Back Panel
Shelf Base Panel
Drawer Front Panel
Drawer Side Panel (L)
Drawer Side Panel (R)
Drawer Back Panel
Drawer Bottom Panel
Drawer Support Panel
(P22)
Front Support Top Panel
(P16)
Ladder Support Bar

Page 5
fantasticfurniture.com.au
What You Need
to assemble the product
Other tools you need
Phillips Head screwdriver;
Hammer
Hardware list:
18 x Screws
23 x Large Dowels
5 x Cover Stickers
(H3) (H4)
(H7)
(H11)
1 x Wrench
38 x Nuts
Glides (H18)
14 x Feet
(H12)
Runner (H6d)
24 x Screws
Track (H6c)
Track (H6a) Runner (H6b)
4 x CL Runner
(H13) (H14)
8 x Screws 52 x Screws
4 x DL 4 x CR Runner 4 x DR 38 x Screws
(H8)
6 x Screws
(H9) (H10)
18 x Screws
3 x Washers
1 x Allen Key
72 x Cam Nuts 72 x Cam Bolts
(H1) (H2) (H6)
54 x Small Dowels
(H5)
28 x Nails
(H15)
1 x Bracket
(H16)
2 x Brackets
(H17) (H19)
6 x Pads
(H20)
1 x Caster With
Brake (H23) (H24)
1 x Caster 1 x Caster With
Brake (H25)
1 x Caster
(H22)
(H21)

Page 6
fantasticfurniture.com.au
You will needYou will need
You will need
Step 1: To Assemble The Desk
Step 2
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
Phillips Head
Screwdriver
(H2)
14 x Cam Bolts
Phillips Head
Screwdriver
(H2)
P37
P35 (H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
4 x Cam Nuts
(H1) (H5)
4 x Small Dowels
Attach 14 x Cam Bolts (H2) to the Shelf Front Panel (P37) and Shelf Rear
Panel (P35) by tightening with a Phillips Head Screwdriver.
Insert 4 x Cam Nuts (H1) and 4 x Small Dowels (H5) into the 2 x Shelf Panels (P38) as shown.
Rotate the cam nuts so the arrows face the incoming bolts.
Attach the 2 x Shelf Panels (P38) to the Shelf Rear Panel (P35), by tightening the cam nuts
with a Phillips Head Screwdriver.
(H1)
P35
This side has raw edge
P38
P38
(H1)
(H1)
(H1)
(H5)
(H5)
(H5)
(H5)

Page 7
You will need
Step 3
Step 4
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
P36
P38
P38
P35
Phillips Head
Screwdriver
3 x Cam Nuts
(H1) (H5)
This side has raw edge
2 x Small Dowels
Slot in the Shelf Middle Panel (P36) into the grooves of the 2 x Shelf Panels (P38) as shown.
Insert 3 x Cam Nuts (H1) and 2 x Small Dowels (H5) into the Shelf Back Panel (P39) as
shown. Rotate the cam nuts so the arrows face the incoming bolts.
Attach the Shelf Back Panel (P39) to the Shelf Rear Panel (P35) by tightening the cam
nuts with the Phillips Head Screwdriver.
fantasticfurniture.com.au
P39
(H1)(H5)
P35
(H1)
(H1)
(H5)

Page 8
fantasticfurniture.com.au
You will need
Step 5
You will need
Step 6
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
(H1)
(H1)
(H1)
(H5)
(H5)
(H5)
(H1)
(H1)
(H5)
P39
P37
P38
P38
Phillips Head
Screwdriver
7 x Cam Nuts
(H1) (H5)
P40
(H24)
(H13)
(H13)
(H25)
1 x Caster With
Brake (H25)
(H24)
1 x Caster
(H13)
8 x Screws
6 x Small Dowels
Insert 3 x Cam Nuts (H1) and 2 x Small Dowels (H5) into
the Shelf Back Panel (P39). Rotate the cam nuts so the arrows face the incoming bolts. Insert
4 x Cam Nuts (H1) and 4 x Small Dowels (H5) into the 2 x Shelf Panels (P38).
Rotate the cam nuts so the arrows face the incoming bolts.
Attach the Shelf Front Panel (P37) to the 2 x Shelf Panels (P38) and Shelf Back Panel (P39), by
aligning the holes and tightening Cam Nuts with a Phillips Head Screwdriver.
Attach the Caster (H24) and Caster with Brake (H25) to Shelf Base Panel (P40)
with 8 x Screws (H13), tightening with a Phillips Head Scr ewdriver.

Page 9
fantasticfurniture.com.au
You will need
Step 7
Phillips Head
Screwdriver
You will need
Step 8
8 x Screws
(H7) Track (H6a)
1 x CL Runner
(H5)
6 x Small Dowels
(H2)
2 x Cam Bolts
(H14)
3 x Screws
(H2)
2 x Cam Bolts 2 x Small Dowels
(H5)
Track (H6c) (H14)
7 x Screws
1 x CR Runner
2 x Brackets
(H17) Phillips Head
Screwdriver
Insert 6 x Small Dowels (H5) into panels (P35, P37 & P36).
Attach the Shelf Base Panel (P40) to panels (P35,P36, P37 & P39) with 8 x Screws (H7), tightening with a
Phillips Head Screwdriver.
Attach the CL Runner Track (H6a) to the Shelf Back Panel with 3 x Screws (H14) by tightening with a Phillips
Head Screwdriver.
Insert 2 x Cam Bolts (H2) into the Shelf Back Panel (P39), tightening with a Phillips Head Screwdriver.
Attach CR Runner Track (H6c) to the Desk Side Panel (P32) with 3 x Screws (H14) by tightening with
a Phillips Head Screwdriver.
Insert 2 x Cam Bolts (H2) into Desk Side Panel (P32), tightening with a Phillips Head Screwdriver.
Insert 2 x Small Dowels (H5) into Desk Side Panel (P32).
Attach 2 x Brackets (H17) to Desk Side Panel (P32) with 4 x Screws (H14), tightening
with a Phillips Head Screwdriver.
(H5)
(H5)
(H6c)
(H14)
(H14)
(H2)
(H14)
(H14)
(H17)
P32
(H17)
(H14)
(H14)
(H6c)
(H2)
(H14)
(H7)
(H6a)
(H7)
(H7)
(H7)
(H7)
(H7)
(H7)
(H14)
(H14)
(H7)
(H2)
P39
P35
P37
P40
P36
(H5)
(H5)
(H14)
(H6a)
(H2)

fantasticfurniture.com.au Page 10
You will need
Step 9
Step 10
(H11)
2 x Nuts
(H5)
face incoming
screw
Opening of nut
You will need
2 x Screws
(H8)
1 x Allen Key
(H21)
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
(H1)
4 x Cam Nuts
6 x Small Dowels
Insert 6 x Small Dowels (H5) into Desk Back Panel (P33) and Support Panel (P34).
Insert 2 x Nuts (H11) into Desk Back Panel (P33).
Rotate the nuts so the opening faces the incoming screws.
First insert 4 x Cam Nuts (H1) into the Desk Back
Panel (P33) and Support Panel (P34).
Rotate the cam nuts so the arrows face the incoming bolts.
Then attach panels (P33 & P34) to panel (P39). Tighten the cam nuts with Phillips Head Screwdriver.
Insert 1 x Screw (H8) through panel (P39) to panel (P33) and tighten with the Allen Key (H21). Attach
panels (P33 & P34) to panel (P32). Tighten Cam Nut with the Phillips Head Screwdriver. Insert 1 x
Screw (H8) through panel (P32) to panel (P33) and tighten with the Allen Key (H21).
(H8)
(H11)
P39
P33
P34
P32
(H1)
(H2)
(H1)
(H11)
(H11)
(H5)
(H5)
(H5)
(H5)
P33
P34 (H5)
(H5)