fantastic furniture Havana Display Cabinet 2 Door User manual

Version 1.0
Havana
Display Cabinet 2 Door
fantasticfurniture.com.au

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 25kgs /Shelf.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2
Glass should always be handled with care.
cause glass to break. This glass is designed to break into small,
relatively harmless pieces and not sharp fragments. Avoid
placing hot or cold items directly onto the table unless using a
thick insulation material such as placemats or coasters.
Avoid dropping objects onto the glass.
Do not allow hard or pointed objects to come into contact
with the glass. Never use the top area as a chopping surface.
Do not sit or stand on the glass surface.

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Leg (P4);
Leg (P5);
Leg (P6);
Leg (P7);
3 x Shelf Panels (P8):
Bottom Panel (P9):
4 x Back Panels (P10) :
Left Door (P11)
Right Door (P12)
Hardware pack
Shelf
Panel (P8)
Shelf
Panel (P8)
Shelf
Panel (P8)
Bottom
Panel (P9)
Back Panel
(P10)
Back Panel
(P10)
Back Panel
(P10)
Back Panel
(P10)
Door
(P11)
Door
(P12)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
Right Side
Panel
(P3)
Left Side
Panel
(P2)
Leg
(P4)
Leg
(P5)
Leg
(P6)
Leg
(P7)
Top Panel
(P1)
20 x Dowels
(H1)
12 x Large Dowels
(H5)
2 x Buer
Plates
(H2)
1 x Allen Key
(H7)
28 x Cam
Bolts
(H3)
28 x Cam
Nuts
(H4)
36 x Screws
(H11)
6 x Hinges
(H10)
2 x Handles
(H8)
4 x Handle
Bolts
(H9)
4 x Plastic
Glides (H12)
8 x Wedges
(H13)
8 x Wedge
Screws (H14)
1 x Safety
Strap
(H15)
2 x Washers
(H17)
1 x Safety
Strap Screw
(H16)
14 x Bolts
(H6)

H3
H3
H3
H3
(P3)
(P2)
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
6 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Attach 6 x Cam Bolts (H3) to Right Side Panel (P3) by tightening with the Phillips Head
Screwdriver.
Attach 6 x Cam Bolts (H3) to Left Side Panel (P2) by tightening with the Phillips Head
Screwdriver.
fantasticfurniture.com.au Page 5
6 x Cam Bolts
(H3)
H3
H3
H3
H3
H3
H3
H3
H3

You will need
Step 3
Step 4
You will need
Insert 6 x Dowels (H1) and 6 x Cam Nuts (H4) into Shelf Panels (P8x3) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts. Attach
Shelf Panels (P8x3) to Left Side Panel (P2) by tightening the Cam Nuts (H4) with
the Phillips Head Screwdriver.
Insert 6 x Dowels (H1) and 6 x Cam Nuts (H4) into Shelf Panels (P8x3) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts. Attach
Shelf Panels (P8x3) to Right Side Panel (P3) by tightening the Cam Nuts (H4)
with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
6 x Dowels
(H1)
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
H1
H4
H4 H4
H4 H4
H4
H4
H4
H4
H4
H1
H1
H1
H1
H1
(P8)
(P8)
(P8)
(P8)
(P8)
(P8)
(P2)
(P3)
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
6 x Cam Nuts
(H4)
6 x Dowels
(H1)
6 x Cam Nuts
(H4)
Make sure cam
nut hole face top
Back panel
slot
Make sure cam
nut hole face top

Attach Bottom Panel (P9) to Left & Right Side Panels (P2 & P3) with 4 x Dowels (H1) and
2 x Bolts (H6) by tightening with the Allen Key (H7) as shown.
Attach 10 x Cam Bolts (H3) to Legs (P7 & P5) by tightening with the Phillips Head Screwdriver.
You will need
Phillips Head
Screwdriver
Step 6
You will need
Step 5
H6
H6
H7
H1
H3
H3
H3
H3
H3
H3
H3 H3
H3
H3
H1
H1
(P9)
(P7)
(P5)
(P2)
(P3)
fantasticfurniture.com.au Page 7
4 x Dowels
(H1)
10 x Cam Bolts
(H3)
1 x Allen Key
(H7)
H6
H7
2 x Bolts
(H6)
Tighten the
bolts at 90%.

Insert 4 x Large Dowels (H5)
into Bottom Panel (P9) as shown.
Insert 10 x Cam Nuts (H4) into Left &
Right Side Panels (P2 & P3) and Bottom
Panel (P9) as shown. Rotate the cam nuts so the
arrow points towards the incoming cam bolts. Attach
Legs (P5 & P7) to Left & Right Side Panels (P2 & P3) and
Bottom Panel (P9) by tightening the Cam Nuts (H4)
with the Phillips Head Screwdriver.
You will need
Step 7
Carefully turn the unit over. Attach Leg (P6) to Right Side Panel (P3) with 6 x
Bolts (H6) by tightening with the Allen Key (H7).
Phillips Head
Screwdriver
10 x Cam Nuts
(H4)
You will need
Step 8
H4
H4
H4
H6
H6
H6
H6 H6
H4
H4
H4
H4
H4
H4
H4 H5
H5
(P7)
(P9)
(P9)
(P5)
(P6)
(P2)
(P3)
(P3)
fantasticfurniture.com.au Page 8
4 x Large
Dowels (H5)
1 x Allen Key
(H7)
H7
6 x Bolts
(H6)
Required
Two People

Step 10
Align holes on Leg (P4) with Shelf Panels (P8x3) and Bottom Panel (P9).
Step 9
Gently stand the unit on it’s side as shown. Slide Back Panels (P10x3) into the grooves of
Shelf Panels (P8x3) & Bottom Panel (P9).
(P10)
(P10)
(P10)
(P8)
(P8)
(P8)
(P8)
(P8)
(P8)
(P9)
(P6)
(P2)
(P9)
(P4)
fantasticfurniture.com.au Page 9
Ensure laminated
side of panel is
facing inwards.

You will need
Step 11
Attach Leg (P4) to Left Side Panel (P2)
with 6 x Bolts (H6) by tightening with the
Allen Key (H7). Attach 4 x Plastic Glides (H12)
to Legs (P4&P5&P6&P7) with the Hammer. Fully
tighten 2 x Bolts (H6) on Bottom Panel (P9)
with the Allen Key (H7).
Gently stand the unit upright. Slide Back Panel (P10) into the grooves of
Legs (P4 & P9).
Step 12
H12
H7
H6
H6
H12
H12
H12
(P2)
(P9)
(P6)
(P4)
(P5)
(P7)
(P8)
(P6)
(P4)
(P10)
fantasticfurniture.com.au Page 10
4 x Plastic
Glides (H12) Hammer
Ensure laminated
side of panel is
facing inwards.
1 x Allen Key
(H7)
6 x Bolts
(H6)
H6
H7
H6
H6
H6
H6
Required
Two People