fantastic furniture Palermo User manual

Palermo
Lowline 1400mm Walnut

r

Top Panel(P1)
Bottom Panel(P2)
Right Panel(P3)
Left Panel(P4)
M-Left Panel(P5)
M-Right Panel(P6)
Middle Shelf(P7)
2 x Support Rails(P8)
M-Back Panel(P9)
2 x Back Panels(P10)
Left Door(P11)
Right Door(P12)
4 x Legs(P13)
2 x Support Rails(P14)
Hardware Pack
20 x Cam Bolts
(H1)
20 x Cam Nuts
(H2)
28 x Dowels
(H3)
4 x Hinges
(H4) 36 x Short Screws
(H5)
16 x Washers
(H7)
1 x Allen Key
(H9) 4 x Levelling Feet
(H10)
12 x Wedges
(H11)
2 x Long Screws
(H12)
4 x Washers
(H13)
2 x Wall Straps
(H14)
Rails
2 x Felt Pads
(H15)
12 x Short Bolts
(H8)
4 x Long Bolts
(H6)
Top Panel
(P1)
Bottom Panel
(P2)
Leg
(P13)
Leg
(P13)
Leg
(P13)
Support Rails
(P14)

16 x Washers
(H7)
12 x Short Bolts
(H8)
1 x Allen Key
(H9)
4 x Levelling Feet
(H10)
H15
H10
H 9
H 8
H 7
4 x Long Bolts
(H6)
H 6
H 7
H 1 5
2 x Felt Pads
(H15)
P14
P 1 4
8 x Cam Bolts
(H1)
8 x Dowels
(H3)
Phillips Head
Screwdriver
Insert 8 x Dowels (H3) into Bottom Panel (P2) and secure 8 x Cam Bolts (H1)
into (P2) by tightening with the Phillips Head Screwdriver.Bottom Panel
(P2)
Stick 2 x Felt Pads (H15) to the centre of .
Align and position 4 x Legs (P13) onto the pre-drilled holes on the
Bottom Panel (P2). Align and position the 2 x (P14)
between the Legs (P13) as shown ensuring the side with the Felt Pads (H15)
is on the Bottom Panel (P2).Using 3 x Washers (H7) and 3 x Short Bolts (H8),
secure 1 x Leg (P13) to the Bottom Panel (P2), tightening using the Allen Key (H9).
Secure the to the Leg (P13) and Bottom Panel (P2)
using 1 x Washer (H7) and 1 x Long Bolt (H6), tightening using the Allen Key (H9).
Repeat this step for the other 3 x Legs (P13).
Support Rails (P14)
Support Rails
Support Rails (P14)
H 6
H 7
H 9
H 7
H 8
H 9
P 1 3
P13
P13
P13

4 x Cam Bolts
(H1)
4 x Dowels
(H3)
Phillips Head
Screwdriver
Insert 2 x Dowels (H3) into M- Right Panel (P6) and secure 2 x Cam Bolts (H1) into
M-Right Panel (P6) by tightening with the Phillips Head Screwdriver.
Repeat this step for M-Left Panel (P5).
(P5)
Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
Insert 2 x Cam Nuts (H2) into Middle Shelf (P7) as shown.Rotate the cam nuts
so the arrows point towards the incoming cam bolts.
Attach Middle Shelf (P7) to M-Right Panel (P6) by tightening the Cam Nuts (H2)
with the Phillips Head Screwdriver

2 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Insert 2 x Cam Nuts (H2) into Middle Shelf (P7) as shown.Rotate the cam
nuts so the arrows point towards the incoming cam bolts.
Attach Middle Shelf (P7) to M-Left Panel (P5) by tightening the Cam Nuts (H2)
with the Phillips Head Screwdriver
4 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Insert 4 x Cam Nuts (H2) into M-Left Panel (P5) and M-Right Panel (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach the assembled frame (P5, P6) onto the Bottom Panel (P2) as shown.
Ensure the grooves on the panels are all aligned.
Secure together by tightening the Cam Nuts (H2) using the Phillips
Head Screwdriver.

Page 8
7
8
Slide M-Back Panel (P9) into the grooves of M-Left Panel (P5)
, M-Right Panel (P6) and Bottom Panel (P2) as shown.
Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
4 x Dowels
(H3)
Insert 2 x Dowels (H3) into M-Right Panel (P6) and Support Rail (P8)
Insert 2 x Dowels (H3) into Right Panel (P3) and Support Rail (P8)
Insert 2 x Cam Nuts (H2) into Right Panel(P3).Rotate the cam nuts
so the arrows point towards the incoming cam bolts.
Attach Right Panel (P3) to Bottom Panel (P2) by tightening the Cam
Nuts (H2) with the Phillips Head Screwdriver.
Ensure the grooves on each panel aligns as shown.
(P2)
(P6)

Page 9
9
10
Slide one Back Panel (P10) into the groove of M-Right Panel (P6)
and Right Panel (P3) as shown.
(P10)
(P6)
(P3)
Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
4 x Dowels
(H3)
Insert 2 x Dowels (H3) into M-Left Panel (P5) and Support Rail (P8)
Insert 2 x Dowels (H3) into Left Panel (P4) and Support Rail (P8)
Insert 2 x Cam Nuts (H2) into left Panel (P4).Rotate the cam nuts so
the arrows point towards the incoming cam bolts.
Attach Left Panel (P4) to Bottom Panel (P2) by tightening the Cam
Nuts (H2) with the Phillips Head Screwdriver.
Ensure the grooves on each panel aligns as shown.
(P4)
(P5)

Page 10
11
12
Slide another Back Panel (P10) into the groove of M-left Panel (P5) and
left Panel (P4) as shown.
(P4)
(P10) (P5)
8 x Cam Bolts
(H1)
8 x Dowels
(H3)
Phillips Head
Screwdriver
Insert 8 x Dowels (H3) into Top Panel (P1). Secure 8 x Cam Bolts (H1) to Table Top (P1)
by tightening with the Phillips Head Screwdriver.
(P1)