fantastic furniture COMO TALLBOY 6 DRW User manual

Version 1.0
Como
Dresser 6 Drw
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 10kgs /Drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Divider (P4);
6 x Rails (P5);
Rails (P6);
Rail (P7);
Rail (P8);
2 x Back Panels (P9);
3 x Drawer Front (P10);
3 x Drawer Front (P11);
6 x Left Drawer Sides (P12);
6 x Right Drawer Sides (P13);
6 x Drawer Bases (P14);
6 x Drawer Backs (P15);
6 x Support Rail (P16)
Hardware pack
31 x Dowels
(H1)
6 x Long
Dowels
(H16)
36 x Long
Screws
(H2)
88 x Small
Screws
(H5)
6 x CL Runner
Tracks
(H6)
6 x CR Runner
Tracks
(H7)
13 x Cam Bolts
(H3)
13 x Cam Nuts
(H4)
30 x Small
Cam Nuts
(H11)
6 x DL Runners
(H8)
6 x DR Runners
(H9)
30 x Small
Cam Bolts
(H10)
4 x Long
Screws
(H15)
6 x Plastic
Glides
(H17)
1 x Screw
(H13)
1 x Safety Strap
(H12)
2 x Washers
(H14)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel
(P2)
Divider
(P4)
Rail
(P5)
Rail
(P5)
Rail
(P5)
Rail
(P6)
Rail
(P7)
Rail
(P8)
2 x Back
Panel
(P9)
Left
Drawer Side
(P12)
Drawer Front
(P10,P11)
×6
Right Drawer
Side (P13)
Drawer Back
(P15)
Drawer
Base (P14)
Support
Rail
(P16)

You will need
Step 3
18 x Dowels
(H1)
Phillips Head
Screwdriver
9 x Small
Screws (H5)
H7
CR
H5
9 x Small
Screws (H5)
6 x Cam Bolts
(H3)
H5
H5
H5
H5
H5
H5
H5
H5
H7
H7
H7
H5
(P3)
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
Attach 3 x CL Runner Tracks (H6) to Left Side Panel (P2) with 9 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Attach 3 x CR Runner Tracks (H7) to Right Side Panel (P3) with 9 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
3 x CL Runner
Tracks (H6)
H6
CL
H5
3 x CR Runner
Tracks (H7)
Phillips Head
Screwdriver
Insert 18 x Dowels (H1) into Left Side Panel
(P2). Attach 6 x Cam Bolts (H3) into Side Panels
(P2) and (P3) as shown. Tighten with a Phillips Head Screwdriver.
H5
H5
H6
H6
H6
H5
H5
H5
H5
H5
H5
H5
(P2)
H1 H1
H1
H1
H1
H1
H1
H3
H3
(P3)
(P2)
H1 H1
H1
H1
H1
H1
H1
H1
H1
H1
H3
H3
H3
H1
H3

This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 5
You will need
Phillips Head
Screwdriver
Step 4
You will need
H7
CR
H5
9 x Small
Screws (H5)
Step 6
You will need
Phillips Head
Screwdriver
Attach 3 x CL Runner Tracks (H6) to Divider (P4) with 9 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Insert 1 x Cam Nut (H4) into the hole of Rail (P6). Rotate the cam nut so the arrows
point towards the incoming cam bolt. Insert 1 x Dowel (H1) into Rail (P6). Attach 1 x
Cam Bolt (H3) into Rail (P6) as shown. Attach 3 x Rails (P5) and Rail (P6) to Right
Side Panel (P3), then tighten the cam nuts.
(P4)
H5
H5
H5
H5
H5
H5
H5
H5
H7
H7
H7
H5
Turn Divider (P4) over to the other side, and then attach 3 x CR Runner Tracks (H7)
with 9 x Small Screws (H5).
(P5)
(P5)
(P5)
(P6)
(P3)
H4
H1
H3
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
H6
CL
H5
3 x CR Runner
Tracks (H7)
(P4)
H5
H5
H6
H6
H5
H5
H5
H5
H5
H5
H5
9 x Small
Screws (H5)
Phillips Head
Screwdriver
3 x CL Runner
Tracks (H6)
1 x Dowels
(H1)
1 x Cam Bolts
(H3)
1 x Cam Nuts
(H4)

Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
You will need
Step 8
You will need
Step 7
Insert 2 x Cam Nuts (H4) into the holes of Rails (P7) and (P8).
Rotate the cam nuts so the arrows point towards
the incoming cam bolts and tighten the cam nuts.
H4
(P3)
(P4)
(P6)
Insert 1 x Cam Nut (H4) into the hole of Divider (P4).
Rotate the cam nut so the arrows point towards the incoming cam bolt.
Push Divider (P4) into place and tighten the cam nut.
H16
H16
H16
(P4) (P5)
(P5)
(P5)
(P3)
6 x Long
Dowels (H16)
Insert 6 x Long Dowels (H16) into 3 x Rails (P5) and Divider (P4).
(P4)
(P7)
(P8)
(P3)
H4
H4
fantasticfurniture.com.au Page 7
You will need
Step 9
Phillips Head
Screwdriver
1 x Cam Nuts
(H4)

You will need
Step 11
Insert 3 x Cam Nuts (H4) into the holes of Rails (P6,P7) and (P8).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Left Side Panel (P2) into place and tighten the cam nut.
Attach Rails (P7) and (P8) to Divider (P4) with 4 x Long Screws (H15).
Then hammer 6 x Plastic Glides (H17) on Side Panels (P2,P3) and Divider (P4).
Attach 6 x Cam Bolts (H3) into Top Panel (P1) as shown. Tighten with a Phillips Head Screwdriver.
You will need
Step 10
Phillips Head
Screwdriver
Hammer
6 x Cam Bolts
(H3)
3 x Cam Nuts
(H4)
4 x Long
Screws (H15)
6 x Plastic
Glides (H17)
fantasticfurniture.com.au Page 8
Phillips Head
Screwdriver
(P6)
(P2)
(P3)
H4
H4
H4
H15 H15
H15
H17
H17
H17
H17
H17
H17
(P1)
H3
H3
H3
H3
H3
H3
H17
20mm

Insert 6 x Dowels (H1) into
Side Panels (P2,P3) and Divider (P4).
Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2,P3) and Divider (P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts.
6 x Cam Nuts
(H4)
H5
H5
(P9)
(P9)
28 x Small
Screws (H5)
fantasticfurniture.com.au Page 9
You will need
Step 12
Phillips Head
Screwdriver
You will need
Step 13
Phillips Head
Screwdriver
(P1)
(P2)
(P3)
H1
H1
H1
H4
H4
H1
H4
Required
Two People
Required
Two People
6 x Dowels
(H1)
Put 2 x Back Panels (P9) into the groove on
the back of the chest ,screw them with
28 x Small Screws (H5). Holes are not pre-drilled so you need to
put some pressure with screwdriver to get started. Lift unit back up.

1 x Dowels
(H1)
5 x Small
Cam Bolts (H10)
H10 H10
(P10)
H10
H10
H10
H1
5 x Small
Cam Nuts (H11)
fantasticfurniture.com.au Page 10
You will need
Step 14
Phillips Head
Screwdriver
You will need
Step 15
Phillips Head
Screwdriver
Step 16
Insert 1 x Dowel (H1) into Drawer Front (P10). Attach 5 x Small Cam Bolts (H10) as shown.
H11
H11
H11
H11
H11
(P10)
(P12)
(P13)
(P16)
Insert 5 x Small Cam Nuts (H11) into the holes of
Drawer Sides (P12,P13) and Support Rail (P16).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Side (P12,P13) and Support Rail (P16) into place and tighten the cam nuts.
(P10)
(P14)
(P12)
(P13)
Slide Drawer Base (P14) into the groove in Drawer Sides (P12,P13).