fantastic furniture COMO ROBE 2 DOOR User manual

Version 1.0
Como
Robe 2 Door
fantasticfurniture.com.au
APPROVED LP 02/03/21

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 18kgs /Drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Shelf Panel (P4);
Rail (P5); 2 x Rails (P6);
Rail (P7); Rail (P8);
Back Panel (P9);
Long Connect Stick (P10);
Short Connect Stick (P11);
Left Door (P12);
Right Door (P13);
2 x Drawer Fronts (P14)
2 x Left Drawer Sides (P15);
2 x Right Drawer Sides (P16);
2 x Drawer Bases (P17);
2 x Drawer Backs (P18);
2 x Support Rails (P19)
Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
Top Panel
(P1)
Right Side
Panel
(P3)
Right
Door
(P13)
Left
Door
(P12)
Left Drawer
Side
(P15)
Drawer Front
(P14)
x 2
Right Drawer
Side (P16)
Drawer Back
(P18)
Drawer Base
(P17)
Support
Rail
(P19)
Left Side
Panel
(P2)
Rail
(P8)
Rail
(P5)
Rail
(P6)
Rail
(P6)
Rail
(P7)
Back
Panel
(P20)
Back
Panel
(P9)
Shelf
Panel
(P4)
Long Connect
Stick (P10)
Short Connect
Stick (P11)
26 x Dowels
(H1)
12 x Long
Screws
(H2)
58 x Small
Screws
(H5)
28 x Timber
Screws
(H17)
2 x Clothes
Hanger Support
(H14)
1 x Clothes
Hanger
(H15)
4 x Hinges
(H16)
2 x CL Runner
Tracks
(H6)
2 x CR Runner
Tracks
(H7)
15 x Cam
Bolts
(H3)
15 x Cam
Nuts
(H4)
10 x Small
Cam Nuts
(H11)
2 x Catapult
Base
(H12)
2 x Catapult
(H13)
2 x DL Runners
(H8) 2 x DR Runners
(H9)
10 x Small
Cam Bolts
(H10)
1 x Screw
(H19)
1 x Safety Strap
(H18)
2 x Washers
(H20)
6 x Plastic
Glides
(H21)
1 x Wedge
(H22)
2 x Steel Plate
(H23)

You will need
Step 2
12 x Dowels
(H1)
Phillips Head
Screwdriver
12 x Small
Screws (H5) H7
CR
H5
7 x Cam Bolts
(H3)
You will need
Step 1
Phillips Head
Screwdriver
fantasticfurniture.com.au Page 5
2 x CL Runner
Tracks (H6)
H6
CL
H5
(P2)
(P3)
H5
H5
H5
H5
H5
H5
H6
H6
H5
H5
H5 H7
H7
H5
H5
H5
H3
H3
H1
H1
H1
H1
H1 H1
H1 H1
H1
H1
H1
H1
H3
H3
H3
H3
H3
(P2)
Attach 2 x CL Runner Tracks (H6) to
Left Side Panel (P2) and 2 x CR Runner
Tracks (H7) to Right Side Panel (P3) with
12 x Small Screws (H5).
Insert 12 x Dowels (H1) into Left Side Panel (P2).
Attach 7 x Cam Bolts (H3) to Left Side Panel (P2) as shown.
2 x CR Runner
Tracks (H7)

This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 4
You will need
1 x Cam Nut
(H4)
Phillips Head
Screwdriver
Step 5
You will need
Phillips Head
Screwdriver
Step 3
You will need
Phillips Head
Screwdriver
7 x Cam Bolts
(H3)
1 x Cam Bolt
(H3)
H3
H3
H3
H3
H3
H3
H3
(P3)
Attach 7 x Cam Bolts (H3) to Right Side Panel (P3) as shown.
H3
(P8)
(P4)
H4
Attach 1 x Cam Bolt (H3) into the hole of Rail (P8) as shown.
Insert 1 x Cam Nut (H4) into the hole of Shelf Panel (P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolt.
Push Shelf Panel (P4) into place and tighten the cam nut.
(P1) H12
H13
H5
H12 H12
H5
Attach 2 x Catapult Base (H12) to Top Panel (P1)
with 4 x Small Screws (H5) as shown,then insert
2 x Catapult (H13) into the catapult base.
2 x Catapult
Base (H12)
2 x Catapult
(H13)
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
4 x Small
Screws (H5)

2 x Cam Nuts
(H4)
2 x Cam Nuts
(H4)
Phillips Head
Screwdriver
You will need
Phillips Head
Screwdriver
Step 7
You will need
Step 6
Insert 1 x Cam Nut (H4) into the hole of Rail (P7).
Rotate the cam nut so the arrow point towards the incoming cam bolt.
Attach Rails (P5,P7) to Left Side Panel (P2), then tighten the cam nuts.
(P2)
(P5)
(P7)
H4
fantasticfurniture.com.au Page 7
(P2)
(P6)
(P6)
H4
H4
Insert 2 x Cam Nuts (H4) into the holes of 2 x Rails (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach 2 x Rails (P6) to Left Side Panel (P2), then tighten the cam nuts.
Insert 2 x Cam Nuts (H4) into the holes of 2 x Rails (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach 2 x Rails (P6) to Left Side Panel (P2), then tighten the cam nuts.

You will need
Step 9
Attach 4 x Small Cam Bolts (H10) into
Drawer Front (P8). Tighten with a Phillips
Head Screwdriver.
Insert 12 x Dowels (H1) into the holes of
Panels (P1,P4), 2 x Rails (P6) and Rails (P5,P7,P8).
Insert 7 x Cam Nuts (H4) into the holes of Panels (P1,P4),
2 x Rails (P6) and Rail (P7).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Right Side Panel (P3) into place and tighten the cam nuts.
You will need
Step 8
7 x Cam Nuts
(H4)
Phillips Head
Screwdriver
4 x Small
Cam Bolts (H3)
(P7)
(P4)
(P2)
(P3)
(P6)
(P6)
(P5)
(P1)
(P8)
H4
H4
H4
H4
H4
H4
H1
H1
H1
H1
H1
H1
H1
H1
H1
H4
12 x Dowels
(H1)
fantasticfurniture.com.au Page 8
Phillips Head
Screwdriver
(P2)
(P1)
(P4)
(P8)
H4
H4
H4
H4
Required
Two People

Join Back Panels (P9,P20) with Long Connect Stick (P10) and Short Connect Stick (P11),
then put into the groove on the back of the carcase, colour faces inside,
attach it with 28 x Small Screws (H5). Then hammer 6 x Plastic Glides (H21).
fantasticfurniture.com.au Page 9
You will need
Step 11
Phillips Head
Screwdriver
You will need
Step 10
Phillips Head
Screwdriver
H5
H5
(P2)
(P3)
(P9)
(P20)
(P10)
(P11)
H21
H21
H21
H21
H21
H21
H21
20mm
Required
Two People
H16
H16
H16
H16
H17
H17
(P12)
(P13)
H17
H17
H17
H17
H17
H23
H23
H5
H5
H17
H16
H17 H17
Attach 2 x Steel Plate (H23) to Doors (P12,P13) with 2 x Small Screws (H5).
Attach 4 x Hinges (H16) to Doors (P12,P13) with 8 x Timber Screws (H17).
28 x Small
Screws (H5)
6 x Plastic
Glides(H21)
Hammer
2 x Small
Screws (H5)
8 x Timber
Screws (H17)
4 x Hinges
(H16)
2 x Steel Plate
(H23)

fantasticfurniture.com.au Page 10
You will need
Step 12
Phillips Head
Screwdriver
You will need
Step 13
Phillips Head
Screwdriver
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P9) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P10) with 4 x Small Screws (H5). Repeat step 9 to step 14
to assemble the other drawer.
Required
Two People
Required
Two People
(P2)
(P3)
H15
H17 H14
H17
H16
(P3)
(P2)
(P13)
(P12)
H17
H17
Attach Left Door (P12) to Left Side Panel (P2) and Right Door (P13)
to Right Side Panel (P3) with 16 x Timber Screws (H17).
2 x Clothes
Hanger Support
(H14)
1 x Clothes
Hanger (H15)
4 x Timber
Screws (H17)
16 x Timber
Screws (H17)