fantastic furniture Lunar User manual

Desk 1 Drawer
fantasticfurniture.com.au
Lunar
Version 1.1

Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
fantasticfurniture.com.au
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasti cfurni ture
Warning: Ensure the wall strap is
attached to avoid serious injury.
To avoid any serious of fatal injury, a wall strap has been provided with
this product to prevent toppling. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.
Recommended weight capacity : 60kg on Top
10kg/Drawer

fantasticfurniture.com.au Page 3
Read through the instructions
carefully before you begin.
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screwsuntil the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a so t surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
components please visit our website Help Centre for further assistance.
Assembly checklist
!Please see page 2for any safety requirements or weight restrictions.
Useful information

2 x Washers
Page 4
fantasticfurniture.com.au
What you need
to assemble the product
Hardware Pack :
Box 1:
16 x Cam Nuts
16 x Cam Bolts 16 x Dowels
Track
12 x Runner Screws
16 x Drawer Screws
Other tools you need
Phillips Head screwdriver;Hammer
Top Panel
Left Side Panel (P3)
Right Side Panel (P4)
Back Panel
Base Panel
Drawer Back Panel
Drawer Side Panel (L)
Drawer Side Panel (R)
Drawer Base Panel
Drawer Front Panel
CL Runner Track DL Runner CR Runner DR Runner
2 x Handle Screws
Drawer Support Panel
Steel Bar
Handle
Support Panel
P1
(H4)
(H3)
4 x Feet Glides
(P1)
(P2)
(P5)
(P6)
(P7)
(P8)
(P9)
(P10)
(P11)
(P12)
(P13)
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
(H1) (H2) (H6)
(H7) (H8) (H9) (H10) (H11)
(H12) (H13) (H14)

Page 5
fantasticfurniture.com.au
Step 1
Step 2
You will need
CL Runner
Track
Phillips Head
Screwdriver
CR Runner
Track
6 x Runner
Screws
You will need
Phillps Head
Screwdriver
(H2)
2 x Dowels
(H1)
6 x Cam Bolts
(H3)
4 x Feet Glides
Hammer
(H7) (H9)
(H6)
(H6)(H6)
P3
P4
(H7)
(H9)
P3
P4
(H3)
(H3)
(H3)
(H
3)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H2)
(H2)
Attach CL Runner Track (H7) to the Left Side Panel (P3) with 3 x Runner Screws (H6), by
tightening with a Phillips Head Screwdriver.
Repeat process to attach CR Runner Track (H9) to the Right Side Panel (P4).
Insert 6 x Cam Bolts (H6) into the Left Side
Panel (P3) and Right Side Panel (P4), by
tightening with a Phillips Head Screwdriver.
Insert 2 x Dowels (H2) into panels (P3 & P4).
Insert 4 x Feet Glides (H3) on to the underside
of the legs by gently using a Hammer as shown.

Page 6
Step 4
You will need
Step 3
Phillips Head
Screwdriver
You will need
Phillips Head
Screwdriver
8x Dowels 7 x Cam Bolts
3 x Drawer
Screws
P1 P2
(H11)
(H11)
(H11)
(H11)
(H1)
(H2)
Add the Steel Bar (P2) to the underside of the Top Panel (P1) with 3 x Drawer Screws (H11), by
tightening with the Phillips Head Screwdriver.
Insert 8 x Dowels (H2) into the Top Panel (P1).
Insert 7 x Cam Bolts (H1) into the Top Panel (P1), by tightening with a Phillips Head
Screwdriver.
fantasticfurniture.com.au
(H1)
(H1)
(H1)
(H1) (H1)
(H1)
(H1)
(H1)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
P1
(H2)
(H2)

Page 7
fantasticfurniture.com.au
Step 5
Step 6
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
You will need
Phillips Head
Screwdriver
6 x Cam Nuts
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
You will need
Phillips Head
Screwdriver
7 x Cam Nuts
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
P3
P4
P5
P6
(H4)
(H4)
(H4)
(H4)
(H4)
(H4)
P5
P3
P4
P1
Insert 6 x Cam Nuts (H4) into the Back Panel (P5) and Support Panel (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach the Base Panel (P5) and Support Panel (P6) to the Left Side Panel (P3) and Right Side Panel
(P4), by tightening all Cam Nuts with the Phillips Head Screwdriver.
Carefully lift the unit onto the Top Panel (P1) as shown.
Insert the 7 x Cam Nuts into panels (P3, P4 & P5) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach panels (P3, P4 & P5) to the Top Panel (P1), by tightening all Cam Nuts with the
Phillips Head Screwdriver.

Page 8
Step 7
Step 8
fantasticfurniture.com.au
You will need
2 x Dowels
Phillips Head
Screwdriver P12
3 x Cam Bolts
(H1) (H2)
(H1)
(H1)
(H1)
(H1)
(H2)
(H2)
Insert 4 x Dowels (H2) into panels (P3 & P4).
Attach the Base Panel (P7) to the panels (P3, P4 & P5) with 7 x Drawer Screws (H11), by
tightening with the Phillips Head Screwdriver.
Insert 3 x Cam Bolts (H1) into the Drawer Front Panel (P12), by tightening with a Phillips
Head Screwdriver. Insert 2 x Dowels (H2) into the Drawer Front Panel (P12).
P4
P3
P7
(H11)
(H11)
(H11)
(H11)
(H11)
(H11)
(H11)
(H2)
(H2)
7 x Drawer
Screws (H11)
You will need
4 x Dowels
Phillips Head
Screwdriver
(H2)

Page 9
fantasticfurniture.com.au
Step 10
Step 9
You will need
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
3 x Cam Nuts
Raw side facing bottom
(H4)
(H4)
(H4)
(H4)
P12
P12
P9
P10
P13
P11
P9
P10
P13
Insert 3 x Cam Nuts (H4) into the Drawer Side Panels (P9 & P10) and Drawer Support Panel
(P13). Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach the Drawer Front Panel (P12) to the panels (P9, P10 & P13), by tightening Cam Nuts
with Phillips Head Screwdriver.
Slot in the Drawer Base Panel (P11) into the grooves of panels (P9, P10 & P11) as shown.

Page10
fantasticfurniture.com.au
Step 11
You will need
Phillips Head
Screwdriver
6 x Drawer
Screws
P13
P8
P9
P10
(H11)
(H11)
(H11)
(H11)
(H11)
Attach the Drawer Back Panel (P8) to the Drawer Side Panels (P9 & P10) and Drawer Support Panel
(P13) with 6 x Drawer Screws (H11), by tightening with a Phillips Head Screwdriver.
(P9)
(H12)
P8
P10
(H13)
You will need
Phillips Head
Screwdriver
Handle 2 x Handle Screws
(H12) (H13)
Attach the Handle (H12) to the Drawer Front (P12) with 2 x Handle Screws (H13), by
tightening with a Phillips Head Screwdriver.
Step 12