Festo CPV..-DI01 series Parts list manual

Brief description
CPV valve termi
nal with direct
connection
type CPV..-DI01
– English
8080242
2017-11c
[8080235]
Compact Performance

Festo 2017-11c2
Translation of the original instructions
Documentation on the product
For all available product documentation
èwww.festo.com/pk
Copyright:
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
Internet: http://www.festo.com
E-Mail: [e-mail]
Reproduction, distribution or sale of this document or communication of
its contents to others without express authorization is prohibited.
Offenders will be liable for damages. All rights reserved in the event that
a patent, utility model or design patent is registered.
English 3............................................

Festo 2017-11c English 3
1 User instructionsEnglish
The CPV valve terminal with field bus direct connection
(CPV Direct) is intended exclusively for use as a slave on
one of the following protocols:
– PROFIBUS-DP (as per EN 50170), Festo field bus,
ABB CS31, Moeller SUCOnet K.
The limit values stated in the section “Technical specifica
tions” must be observed here. Detailed information can be
found in the Pneumatics manual P.BE-CP-DI01-.. .
Warning
SSwitch off the power supply before connecting or
disconnecting plugs (otherwise this could lead to
functional damage).
SUse power supplies which guarantee reliable electri
cal isolation of the operating voltage as per IEC/DIN
EN 60204-1. Consider also the general requirements
for PELV circuits in accordance with IEC/DIN EN
60204-1.
SConnect an earth conductor of sufficient cross-sec
tional area to the terminal marked with the earth
symbol.
If to be used as an explosion-protected operating de
vice, make sure that:
Selectrical contacts are not disconnected under ten
sion
Sthe completely fitted valve terminal with all plugs,
adapters and protective caps complies at least with
protection class IP 64.

Festo 2017-11c English4
2 Connecting and display elements
1Field bus connection
2Connection for
power supply
3Bus status and
power LEDs
4Switching status
display of CP valve
coils
5CP extension
connection
6Switch module
(removed)
1
2
34
5
6
Pin assignment of power supply connection
M12 connection Pin no.
1. 24 V DC operating voltage for electronics and inputs *)
2. 24 V DC load voltage for valves
3. 0 V
4. Earth connection
*) On the extension connection of connected modules

Festo 2017-11c English 5
Example of connection of PELV power unit and potential
equalization
1PE
2Potential
equalization
3Load voltage can
be switched off
separately and
external fuses
4Earth connection
pin 4 (max. 3 A)
PS
MNS
3124
123 42
2 A
2 A
Pin assignment of field bus connection (Sub-D-9 socket)
PROFIBUS-
DP
Festo
field
bus
ABB
CS31
SUCOnet
K
Pin 3 (B) *) RxD/TxD-P S + Bus-1 TA/RA
Pin 8 (A) *) RxD/TxD-N S- Bus-2 TB/RB
Housing
(Cable clip) *)
Screening/shield
*) In brackets: Connection on Festo Sub-D plug type FBS-SUB-9-GS-9
(TN 18529)
Detailed information can be found in the manual
P.BE-CP-DI01-.. .

Festo 2017-11c English6
3 Configuration
Caution
The CPV Direct contains electronically sensitive compo
nents. The CPV Direct will be damaged if you touch the
contact surfaces of the plug connectors and if you do
not observe the regulations for handling electrostati
cally sensitive components.
Proceed as follows when configuring:
1. Switch off the power supply.
2. Remove the switch module.
3. Set the following with the DIL switches: field bus pro
tocol, extension to the CP system, field bus address/
station number, diagnostic mode (only PROFIBUS or
ABB CS31), baud rate (only Festo field bus).
4. Refit the switch module.
5. If the CP system is the first or last slave in a field bus
segment, the terminating resistor in the Festo Sub-D
plug must be activated.
Warning
SMake sure that switch-on test pulses are sup
pressed/switched off when you operate the CPV
Direct via a “safety I/O module”.
SCheck the measures required for putting your system
into a safe status in the event of an EMERGENCY
STOP.
Further information can be found in manual
P.BE-CP-DI01-...

Festo 2017-11c English 7
4 DIL switch
4.1 Setting the field bus protocol (4-element DIL switch)
PROFIBUS-DP Festo field
bus
ABB CS31 SUCOnet K
4.2 Setting the extension of the CP system (4-element
DIL switch)
Extension to the CP system Setting the DIL
switches
CPV Direct without extension
CPV Direct extended with:
– a CP input module
CPV Direct extended with:
– a CP valve terminal/CP output module
CPV Direct extended with:
– a CP valve terminal/CP output module
and
– a CP input module

Festo 2017-11c English8
4.3 Setting the station number (8-element DIL switch)
– PROFIBUS-DP, ABB CS31, SUCOnet K:
8-element DIL switch, switch elements 1...7
– Festo field bus
8-element DIL switch, switch elements 1...6
Coded entry Example: Station number 38
20= 1 21= 2 22= 4 23= 8 24= 16 25= 32 26= 64
21+ 22+ 25=
2 + 4 + 32 =
38

Festo 2017-11c English 9
4.4 Set diagnostic mode (only PROFIBUS-DP and ABB
CS31, 8-element DIL switch)
– PROFIBUS-DP Device-related diagnosis active/inactive
– ABB CS31 Load voltage monitoring active/inactive
Diagnosis ON Diagnosis OFF
4.5 Set the field bus baud rate (only Festo field bus,
8-element DIL switch)
31.25 kBaud 62.5 kBaud 187.5 kBaud 375 kBaud
The CPV Direct has automatic baud rate recognition for all
other protocols.

Festo 2017-11c English10
5 Addressing
The CPV Direct must be addressed differently according to
the field bus protocol. In general the following applies:
1. A CPV valve terminal always occupies 16 output
addresses.
A CP valve location occupies two addresses:
– lower-value address = pilot solenoid 14
– higher-value address = pilot solenoid 12.
2. CP valve terminals, electric input or output modules on
the extension string each occupy 16 input or output
addresses.
Details and examples of addressing the CP system can be
found in the manual P.BE-CP-DI01-.. .

Festo 2017-11c English 11
6 Technical specifications
Type CPV..-DI01
Temperature range
– Operation
– Storage
- 5 °C ... + 50 °C
- 20 °C ... + 70 °C
Relative humidity 95 %, non-condensing
Protection class as per EN 60529 plug
connector inserted or provided with
protective cap
IP65
Protection against electric shock
(protection against direct and indirect
contact as per IEC/DIN EN 60204-1)
by means of PELV circuits
(Protective Extra-Low
Voltage)
Protection against explosion
(as per EU guideline 94/9/
EG, EN 50021 and EN 50281-1-1)
Do not disconnect electrical connec
tions which are under tension.
II 3 G/D EEx nA II T5 X
- 5 °C ≤ Ta ≤+ 50 °C
T 80 °C IP65 (Year of manu
facture see Ex-identification
on the product)
Elektromagnetic compatibility
– Interference emitted
– Immunity against interference
Tested as per DIN EN
61000-6-4 (industry)1)
Tested as per DIN EN
61000-6-2 (industry)
1) The component is intended for industrial use.

Festo 2017-11c English12
Type CPV..-DI01
Pin 1
Operating voltage connection for
electronics
– Rated value
– Tolerance
– Current consumption
24 V DC (protection against
incorrect polarity, fused in
ternally, switches on again
automatically)
20.4...26.4 V
max. 100 mA
Pin 2
Load voltage connection
– Rated value
– Tolerance
– Current consumption
24 V DC (protection against
incorrect polarity, fused in
ternally, switches on again
automatically)
20.4...26.4 V
Sum of all switched-on CP
solenoid valves; see manual
“CP pneumatics”
Residual ripple 4 Vpp (within tolerance)
Electrical isolation Bus interface
opto-decoupled
Valves See Pneumatics manual
P.BE-CPV-..
Detailed information on the CPV Direct DI01 can be found
in the manual P.BE-CP-DI01-.. .