Fisher-Price JEEP 72607 User manual

Instructions
Jeep
Push’n Scoot™
Model Number: 72607
If you experience a problem with this product, or are missing a part,
please call us at 1-800-432-KIDS, rather than return this product to the store.
Please save these instructions for future reference.
Adult assembly is required.
Tools required for assembly: Hammer and Scrap Block of Wood.
Weight Limit: 55 lbs.
Ages: 11/2years - 5 years.
®
’

•Adult supervision is required.
•Never use near steps, sloped driveways, hills, roadways, alleys, swimming pool areas or
other bodies of water.
•Always wear shoes or sneakers.
•Never allow more than one rider.
WARNING
Parts
•If you experience a problem with this product, or are
missing a part, please call us at 1-800-432-KIDS, rather
than return this product to the store.
•Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
•For your convenience, an extra piece of each type of
hardware is included.
•Before assembling the Jeep Push ‘n Scoot™, please
wipe each part with a clean, dry cloth.
•The Jeep Push ‘n Scoot™ comes with cap nut tools to
help you fasten the cap nuts. After one-time assembly is
complete, dispose of the cap nut tools properly.
2
Handle
Spacer
Spacer
Cap Nut Tool - 2
Cap Nut
Cap Nut
Cap Nut
Cap Nut
Cap Nut
Cap Nut
Wheel
Wheel
Wheel
Wheel
“A” Front Axle “B” Front Axle
Washer
Washer
Washer
Washer
Bushing
Bushing
Bushing
Vehicle Body
Rear Axle
11/8" Washer - 4
SHOWN ACTUAL SIZE
®
®

Assembly
CAUTION
Rear Axle
Cap Nut
Scrap Block
of Wood
1
•Place a cap nut on a scrap block of wood.
•Fit the rear axle into the cap nut and tap with a hammer
until secure.
•Slide a wheel, spoke side down, onto the rear axle.
•Slide a spacer onto the rear axle.
Rear Axle
Wheel
Spoke Side Down
Spacer
2
•Insert the rear axle through the holes in the rear of the
vehicle body. Make sure the spacer fits into the hole in
the vehicle body.
Spacer Rear Axle
3
•Turn the vehicle body on its side with the end of the
rear axle facing up.
•Lift the vehicle body up slightly and fit a cap nut tool on
the cap nut.
•Slide a block of wood under the cap nut tool to support
the rear axle.
•Fit the other spacer onto the rear axle and into the hole
in the vehicle body.
Scrap Block of Wood
Vehicle Body
Cap Nut Tool
Vehicle
Body
Spacer
Rear Axle
4
3
Please keep small parts and plastic
bags out of children’s reach. Dispose of
plastic bags properly.
Wheel

•Slide a washer onto the "A" front axle.
•Slide a bushing, narrow side up, onto the "A" front axle.
•Repeat steps and to assemble the "B" front
axle, washer, wheel, bushing and cap nut.
•Identify and separate the "A" and "B" front axles.
•Place the "A" front axle onto a scrap block of wood.
•Slide a washer onto the "A" front axle.
•Slide one of the wheels, spoke side up, onto the "A"
front axle.
•Fit a cap nut onto the end of the "A" front axle.
•Fit a cap nut tool over the cap nut and tap the center
with a hammer until the cap nut is secure.
6
A
•Slide a wheel, spoke side up, onto the end of the
rear axle.
•Fit a cap nut onto the end of the rear axle.
•Fit a cap nut tool over the cap nut and tap the center
with a hammer until the cap nut is secure.
Cap Nut Tool
Spoke Side Up
Cap Nut
Rear Axle
Wheel
5
Assembly
6
7
7
Cap Nut
Cap Nut
Tool
Wheel
Washer
Spoke Side Up
Scrap
Block of
Wood
Bushing
Bushing
"A" Front Axle
Washer
"A"
Front
Axle
B
"A" Front
Axle
"B" Front
Axle
A
•Turn the vehicle body upright.
•Lift the front end of the vehicle body and locate the
side of the vehicle body marked "A".
IMPORTANT! For proper wheel position, the "A" front
axle assembly must be inserted into the hole in the
vehicle body marked "A".
•Insert the "A" front axle up into the hole underneath
the vehicle body marked "A".
•Make sure the bushing fits into the hole in the vehicle
body.
8
Bushing
"A"
Front
Axle
"A" Marking Vehicle
Body
4

•Lower the vehicle body.
•Fit a bushing, narrow side down, onto the exposed end
of the "A" front axle and into the hole in the vehicle
body.
•Fit a cap nut onto the end of the "A" front axle.
•Fit a cap nut tool over the cap nut and tap the center
with a hammer until the cap nut is secure.
•Repeat assembly steps and to assemble the
"B" front axle to the side of the vehicle body marked "B".
•Dispose of the cap nut tools properly.
8
9
Assembly
9
Cap Nut
Cap Nut Tool
"A"
Front
Axle
Bushing
Vehicle Body
•Position the handle over the rear of the vehicle body so
that it leans away from the vehicle body.
•While keeping the vehicle body stationary, insert and
snap the handle into the two holes in the rear of the
vehicle body.
10
Hole
Rear of
Vehicle
Body
Hole
Handle
5
•Make sure the areas where the labels will be applied
are clean and dry.
•Apply the labels as shown in the illustrations.
•For best adhesion, try to avoid applying a label more
than once.
One-time assembly is now complete.
12
10
9
78
34
65
Front View
Back View
Bushing