FURNITUREBOX RHODES User manual

RHODES
ASSEMBLY GUIDE
www.furniturebox.co.uk
Scan QR code for more tips, advice
and assembly video or visit
furniturebox.co.uk/club/rhodes
SCAN ME

• Check you have all the components and
tools listed.
• Remove all ttings from the plastic bags
and separate them into their groups.
• We do not recommend the use of power
drills/drivers for inserting screws, as this
could damage the unit. Only use hand
screwdrivers and Allen keys.
• Keep children and animals away from the
work area, small parts could cause choking
if swallowed.
• Make sure you have enough space to
layout the parts before starting.
• Assemble the item as close to its nal
position (in the same room) as possible.
• Do not overtighten the nuts to avoid
causing damage to the threads.
Important - Please read these instructions fully before starting assembly
SAFETY AND
CARE ADVICE
!
NO POWER TOOLS
Follow us on Instagram
@furniturebox_uk
• Only clean using a damp
cloth and mild detergent,
do no use bleach or
abrasive cleaners.
• From time to time check
that there are no loose
screws on this unit
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre
SAFETY AND CARE ADVICE

www.furniturebox.co.uk
PLEASE CHECK CAREFULLY AND MAKE SURE YOU HAVE ALL
FITTINGS AND TOOLS LISTED BELOW BEFORE YOU START.
NOTE: The quantities above are the correct amount to complete the assembly. In
some cases more ttings may be supplied than are required.
IMPORTANT INFORMATION
TWO
PERSON
MAXIMUM
CAPACITY 100Kg
45 MINUTE
BUILD

Follow us on Instagram
@furniturebox_uk
Construct your furniture on a nice at, soft surface like a carpet, rug, or the
lawn, to avoid any bumps and scratches. First, lay out all your pieces and
check you have all the items listed on the inventory.
TABLE: STEP 1
Don’t tighten any of the bolts until all
components are in place.
Place tabletop [F] face-down on your
at surface. Connect the long leg
frame [G] using 2x washer + bolt set [1]
on either end.
Connect both shorter leg frames [H] to
the tabletop [F] using 2x washer + bolt
set [J]. Then, connect leg frames [H] to
longer leg frame [G] using 4x washer +
bolt set [J].
Once everything is in place, go ahead
and tighten all the bolts with the Allen
key provided (but take care not to over-
tighten).
TABLE: STEP 2
Carefully, and with help,
ip your table onto its feet
and check for stability. Your
table is now complete!

www.furniturebox.co.uk
CHAIR: STEP 1
Don’t fully tighten any of the bolts until all
the components are in place.
Attach 1x seat panel [C] to 1x backrest [B]
using 2x washer + bolt sets [K].
CHAIR: STEP 5
Secure the 2nd armrest to the seat panel
using 2x washer + bolt sets [K].
Once everything is in place, go ahead and
tighten all the bolts with the Allen key
provided (and take care not to over-tighten).
FULL ASSEMBLY INSTRUCTIONS
CHAIR: STEP 2
Attach 1x armrest [A] to backrest [B] using 2x
washer + bolt sets [K].
CHAIR: STEP 6
Carefully place the chair onto its feet and check
stability. Add 1x seat cushion [D] and 1x back
cushion [E]. Your chair is now complete!
Repeat for the other 3 chairs.
CHAIR: STEP 4
Attach a 2nd armrest [A] to the other side
of the frame - connect to the backrest [B]
using 2x washer + bolt sets [K].
CHAIR: STEP 3
Secure seat panel [C] to armrest [A] using 2x
washer + bolt sets [K].

www.furniturebox.co.uk

The cushions (foam inserts and
covers) are not covered by the guarantee.