GE ADTS542F User manual

GE
Measurement & Control
GE Air Data Test Sets
ADTS542F/552F/553F/554F
User Manual K0553 Revision C

© 2015 General Electric Company. All Rights Reserved. Specifications are subject to change without
notice. GE is a registered trademark of General Electric Company. Other company or product names
mentioned in this document may be trademarks or registered trademarks of their respective companies,
which are not affiliated with GE. The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by GE is under license.

ADTS542F/552F/553F/554F User Manual 1
K0553 Revision C
Introduction
This User Manual provides operating instructions for the Air Data Test Sets (ADTS) compatible with the
requirements of first line operation.
Scope
This User Manual contains the description, identification data and operating procedures for the user of this
equipment.
Safety
The manufacturer has designed this equipment to be safe when operated using the procedures detailed in
this manual and the Safety and Installation Guide K0554. Do not use this equipment for any other purpose
than that stated.
This publication contains operating and safety instructions that must be followed to ensure safe operation
and to maintain the equipment in a safe condition. The safety instructions are either warnings or cautions
issued to protect the user and the equipment from injury or damage. Safety instructions are indicated using
a warning symbol in the text.
Use qualified* technicians and good engineering practice for all procedures in this publication.
Pressure
Do not apply pressure greater than the maximum safe working pressure to the equipment.
Toxic Materials
There are no known toxic materials used in this equipment.
Maintenance
The equipment must be maintained using the manufacturer’s procedures and should be carried out by the
manufacturer’s service department or approved service agents.
Technical Advice
For technical advice contact the manufacturer or subsidiary.
* A qualified technician must have the necessary technical knowledge, documentation, special test
equipment and tools to carry out the required work on this equipment.

2 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
Marks and Symbols on the equipment
For the list of GE approved service centres, go to: www.gemeasurement.com
This equipment meets the requirements of all relevant European safety directives.
The equipment carries the CE mark.
This symbol, on the equipment, indicates that the user should read the user manual.
This symbol, on the equipment, indicates a warning and that the user should refer to
the user manual.
Ce symbole, sur l’instrument, indique que l’utilisateur doit consulter le manuel d’utili-
sation. Ce symbole, dans le manuel, indique une situation dangereuse.
This symbol warns the user of the danger of electric shock.
Ce symbole alerte l’utilisateur sur le danger de choc électrique.
Do not dispose of this product as household waste. Use an approved organisation
that collects and/or recycles waste electrical and electronic equipment. For more
information, contact one of these:
- Our customer service department: www.gemeasurement.com
- Your local government office.
The Bluetooth® wireless technology word mark and logos are registered trademarks
owned by Bluetooth® SIG, Inc. and any use of such marks by GE is under license.
Other trademarks and trade names are those of their respective owners.

ADTS542F/552F/553F/554F User Manual 3
K0553 Revision C
Compliance Statements
Note: You can view the compliance information stored on the ADTS Touch as follows:
From the ADTS Touch Dashboard, select:
1. Tools
2. Bluetooth®
3. Select the region or country of interest from the scroll down list, e.g. for Japan select Japan.
FCC Warning Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End
users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user‘s authority to operate the equipment.
USA
ADTS542F/ADTS552F/ADTS553F/ADTS554F
This device has been tested and found to comply with the limits for a class A digital device, pursuant to Part
15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
This device is only authorized for use in a mobile application. At least 20 cm of separation distance between
the ADTS542F device and the user's body must be maintained at all times.
ADTS542F: Contains Transmitter Module FCC ID: QOQWT41.
ADTS552F: FCC ID: 2AAVWADTS552F-01
ADTS Touch
This device has been tested and found to comply with the limits for a class A digital device, pursuant to Part
15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
This device must not be used with any other antenna or transmitter that has not been approved to operate
in conjunction with this device.
FCC ID: 2AAVWADTSTOUCH-01

4 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
ADTS TOUCH-ER
This device has been tested and found to comply with the limits for a class A digital device, pursuant to Part
15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
This device must not be used with any other antenna or transmitter that has not been approved to operate
in conjunction with this device.
FCC ID: 2AAVWADTSTOUCH-02
CANADA
ADTS542F/ADTS552F/ADTS553F/ADTS554F
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below
with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for use with this device.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
ADTS542F: Contains IC ID: 5123A-BGTWT41 - dipole antenna: 50 ohms, 2.3dBi gain
ADTS552F: IC ID: 12097A-ADTS552F01 - patch antenna: 50 ohms, 6.662dBi gain
ADTS542F/ADTS552F/ADTS553F/ADTS554F
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste,
et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage.
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.

ADTS542F/552F/553F/554F User Manual 5
K0553 Revision C
ADTS542F: contient IC ID: 5123A-BGTWT41 - antenne dipole: 50 ohms, 2.3dBi gain
ADTS552F: IC ID: 12097A-ADTS552F01 - antenne patch: 50 ohms, 6.662dBi gain
ADTS Touch
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
This radio transmitter (12097A-ADTSTOUCH01) has been approved by Industry Canada to operate with the
antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
this device.
dipole antenna: 50 ohms, 2.3dBi gain
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
contains IC ID: 12097A-ADTSTOUCH01
ADTS Touch
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio (12097A-ADTSTOUCH01) a été approuvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne
non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits
pour l'exploitation de l'émetteur.
antenne dipole: 50 ohms, 2.3dBi gain
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage.
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
contient IC ID: 12097A-ADTSTOUCH01
ADTS TOUCH-ER
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.

6 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
This radio transmitter (12097A-ADTSTOUCH02) has been approved by Industry Canada to operate with the
antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
this device.
dipole antenna: 50 ohms, 2dBi gain
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
contains IC ID: 12097A-ADTSTOUCH02
ADTS TOUCH-ER
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio (12097A-ADTSTOUCH02) a été approuvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne
non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits
pour l'exploitation de l'émetteur.
antenne dipole: 50 ohms, 2dBi gain
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage.
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
contient IC ID: 12097A-ADTSTOUCH02
MEXICO
The operation of this equipment is subject to the following two conditions: (1) it is possible that this
equipment or device may not cause harmful interference, and (2) this equipment or device must accept
any interference, including interference that may cause undesired operation.
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier
interferencia, incluyendo la que pueda causar su operación no deseada.
BRAZIL
This equipment operates in a secondary manner, that is, does not have the right of protection against
prejudicial interference, even from stations of the same type, and nor can they cause interference to systems
operating in a primary manner.
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em
caráter primário.

ADTS542F/552F/553F/554F User Manual 7
K0553 Revision C
CHINA
ADTS542F: CMIIT - 2015DJ5155
ADTS552F: CMIIT – 2015DJ6744
ADTSTOUCH: CMIIT – 2015DJ5598
KOREA
해당 무선설비는 운용 중 전파혼신 가능성이 있음
For safety related information refer to K0554 “Safety and Installation Guide”.
Table of Contents
Preliminary Pages
Introduction 1
Scope 1
Safety 1
Pressure 1
Toxic Materials 1
Maintenance 1
Technical Advice 1
Marks and Symbols on the equipment 2
Compliance statements 3
Table of Contents (this page) 7
List of Figures 10
List of Tables 12
Associated documents 12
Abbreviations 12
Glossary 16
Pressure Units and Conversion Factors 17
CHAPTER PAGE
1INTRODUCTION
1.1 Description 1-1

8 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
1.2 ADTS542F 1-1
1.3 ADTS552F 1-3
1.4 ADTS553F 1-4
1.5 ADTS554F 1-5
1.6 ADTS Touch 1-5
2INSTALLATION
2.1 Packaging 2-1
2.2 Packaging for Storage and Transportation 2-1
2.3 Returned Goods Procedure 2-2
2.4 Electrical Connection 2-3
2.5 Pneumatic Pressure Connections 2-3
2.6 Positioning of the ADTS 2-4
3OPERATION
3.1 Preparation 3-1
3.2 Power-up routine 3-2
3.3 Dashboard 3-3
3.4 Pitot Static 3-4
3.5 Rate Timer mode 3-8
3.6 Settings 3-11
3.7 Tools 3-19
3.8 Go to ground 3-24
3.9 Manual Venting of the Aircraft Pitot and Static Systems 3-28
3.10 Example Basic Aircraft Test Operation using the ADTS542F 3-30
3.11 Engine Pressure Ratio (EPR) 3-33
3.12 Test sequence 3-34
3.13 Pt Only or Ps Only Control modes 3-41
3.14 Bluetooth® 3-42
Table of Contents

ADTS542F/552F/553F/554F User Manual 9
K0553 Revision C
3.15 ADTS TOUCH-ER (Extended Range) Bluetooth® 3-44
4CALIBRATION
4.1 Introduction 4-1
4.2 PIN codes and PIN protection 4-1
4.3 Calibration process 4-1
4.4 Calibration description 4-4
4.5 Completion of sensor calibration 4-5
5 MAINTENANCE
5.1 Introduction 5-1
5.2 Maintenance Tasks 5-1
5.3 Routine Maintenance 5-2
5.4 Battery care and maintenance 5-2
5.5 Software updates 5-3
6 TESTING AND FAULT FINDING
6.1 Introduction 6-1
6.2 Standard serviceability test 6-1
6.3 ADTS leak check 6-1
6.4 Fault codes and error messages 6-3
7 SPECIFICATION
7.1 Specification 7-1
Table of Contents

10 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
List of Figures
FIG. TITLE PAGE
1-1 ADTS542F General Arrangement 1-1
1-2 ADTS552F General Arrangement 1-3
1-3 ADTS553F General Arrangement 1-4
1-4 ADTS554F General Arrangement 1-5
1-5 ADTS Touch 1-6
1-6 ADTS Touch status indicators 1-6
1-7 ADTS Touch controls 1-7
2-1 ADTS Altitude correction 2-4
3-1 ADTS power-up self test screen 3-2
3-2 Dashboard 3-3
3-3 Measure mode screen 3-4
3-4 Control mode screen 3-5
3-5 Numbered keypad screen 3-6
3-6 Nudge increment/decrement factor selection 3-7
3-7 Rate timer panel 3-8
3-8 Set time panel 3-9
3-9 Measured average rates of change 3-10
3-10 Communications main screen 3-22
3-11 ADTS manuals screen 3-24
3-12 Go to ground main screen 3-25
3-13 Set rate panel 3-25
3-14 Start go to ground action 3-26
3-15 Aircraft going to ground 3-26
3-16 Hold status during go to ground ramp 3-27

ADTS542F/552F/553F/554F User Manual 11
K0553 Revision C
3-17 Aircraft at ground 3-27
3-18 Go to ground complete 3-28
3-19 Manual let-down ADTS542F and ADTS552F 3-29
3-20 Manual let-down ADTS553F 3-30
3-21 Manual let-down ADTS554F 3-30
3-22 EPR Control Screen (Method 1) 3-32
3-23 EPR Control Screen (Method 2) 3-33
3-24 Test sequence screen 3-34
3-25 Test procedure selection screen 3-35
3-26 Test sequences menu 3-35
3-27 Select test procedure step 3-36
3-28 Test sequence screen based on data field input 3-37
3-29 Test sequence data fields 3-38
3-30 Saving the test sequence file 3-39
3-31 ADTS Touch file explorer window 3-41
3-32 Example of Pt Only Control Mode 3-41
3-33 Pt Only control mode 3-42
3-34 Bluetooth® reliable coverage area 3-43
3-35 External Bluetooth® antenna 3-44
3-36 Bluetooth® antenna extension kit 3-45
3-37 Bluetooth® - controller positioning 3-46
5-1 Replacing the o-ring 5-2
5-2 Software update folders 5-4
5-3 Software updates - ADTS Touch 5-5
List of Figures

12 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
Associated documents
K0563 Service manual.
K0554 Safety and Installation Guide.
The following abbreviations may be used in this manual, the abbreviations are the same in the singular and
plural.
List of Tables
TABLE TITLE PAGE
2-1 Conditions for shipping and storage 2-2
3-1 Test set status indications 3-2
3-2 Settings menu 3-11
3-3 Tools menu 3-20
4-1 Calibration requirements ADTS542F 4-2
4-2 Calibration requirements ADTS552F 4-2
4-3 Equipment requirements 4-3
4-4 Calibration check points 4-3
4-5 Adjustment points 4-5
5-1 Maintenance Chart 5-1
5-2 Maintenance tasks 5-1
Abbreviations
AAmpere
abs Absolute
a.c Alternating current
ADTS Air Data Test Set
AMM Aircraft Maintenance Manual

ADTS542F/552F/553F/554F User Manual 13
K0553 Revision C
Alt Altitude
Alt1 Altitude static channel 1
Alt2 Altitude static channel 2
ARINC Air Radio Incorporated
ASI Airspeed indicator
ATE Automatic Test Equipment
CAS Calibrated airspeed
COSHH Control of Substances Hazardous to Health Regulations
cm Centimetre
d.c Direct current
Def Define
e.g. For example
EPR Engine Pressure Ratio
etc. And so on
°C Degrees Celsius
°F Degrees Fahrenheit
Fig. Figure
ft Foot
g Gauge
hHour
HBC High breaking capacity
Hg Mercury
hm Hecto metre
Hz Hertz
IAS Indicated airspeed
i.e. That is
IEC International Electrotechnical Commission
in Inch
inHg Inches of mercury
Abbreviations

14 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
kg Kilogram
km Kilometre
kts Knots
LCD Liquid crystal display
mMetre
mA Milliampere
Mach Speed ratio to the speed of sound
max Maximum
mbar Millibar
min Minute or minimum
mm Millimetre
mph Miles per hour
mV Millivolts
No. Number
PIN Personal identification number
Ps Static pressure
Ps1 Static pressure channel 1
Ps2 Static pressure channel 2
psi Pounds per square inch
PC Personal computer
Pt Total pressure (Pitot)
Pt1 Pitot pressure channel 1
Pt2 Pitot pressure channel 2
Qc Differential pressure Pt1-Ps1
QFE Local atmospheric pressure
QNH Barometric pressure at sea level
REF Reference
RGA Return Goods Authorization (Druck procedure)
RMS Root mean square
Abbreviations

ADTS542F/552F/553F/554F User Manual 15
K0553 Revision C
ROC Rate of climb
RS232 Serial communications protocol
Rt Rate
Rt CAS Rate of CAS
RTC Real time clock
SCPI Standard commands for programmable instruments
SST Standard Serviceability Test
ST Stainless steel
TAS True Airspeed
VVolts
VA Volt Ampere
+ve Positive
-ve Negative
Abbreviations

16 ADTS542F/552F/553F/554F User Manual
K0553 Revision C
The terminology used in this manual is specific and individual interpretation must not be introduced. The
terms are defined as follows:
Glossary
Adjust To bring to a more satisfactory state; to manipulate controls, levers, linkages, etc. to return equip-
ment from an out-of-tolerance condition to an in-tolerance condition.
Align To bring into line; to line up; to bring into precise adjustment, correct relative position or coinci-
dence.
Assemble To fit and secure together the several parts of; to make or form by combining parts.
Calibrate To determine accuracy, deviation or variation by special measurement or by comparison with a
standard.
Check Make a comparison of a measure of time, pressure, temperature, resistance, dimension or other
quality with a known figure for that measurement.
Disconnect To detach the connection between; to separate keyed or matched equipment parts.
Dismantle To take apart to the level of the next smaller unit or down to all removable parts.
Examine To perform a critical visual observation or check for specific conditions; to test the condition of.
Fit Correctly attach one item to another.
Inspect Review the work carried out by Specialists to ensure it has been performed satisfactorily.
Install To perform operations necessary to properly fit an equipment unit into the next larger assembly or
system.
Maintain To hold or keep in any particular state or condition especially in a state of efficiency or validity.
Operate Make sure that an item or system functions correctly as far as possible without the use of test
equipment or reference to measurement.
Readjust To adjust again; to move back to a specified condition; to bring back to an in-tolerance condition.
Reconnect To rejoin or refasten that which has been separated.
Refit Fit an item which has previously been removed.
Remove To perform operations necessary to take an equipment unit out of the next larger assembly or sys-
tem. To take off or eliminate. To take or move away.
Repair To restore damaged, worn out or malfunctioning equipment to a serviceable, usable or operable
condition.
Replace Remove an item and fit a new or a serviced item.
Reset To put back into a desired position, adjustment or condition.
Service To perform such operations as cleaning, lubricating and replenishing to prepare for use.
Test Ascertain by using the appropriate test equipment that a component or system functions correctly.

ADTS542F/552F/553F/554F User Manual 17
K0553 Revision C
Pressure units and conversion factors
Unit Conversion
To convert FROM pressure Value 1 in pressure UNITS 1 TO pressure Value 2 in pressure UNITS 2:
Calculate as follows:
Value 2 = Value 1 x Factor 1 ÷ Factor 2
Pressure units Factor (hPa) Pressure units Factor (hPa)
mbar 1.0 cmH2O @ 20°C 0.978903642
bar 1000.0 mH2O @ 20°C 97.8903642
Pa (N/m2)0.01 kg/m20.0980665
hPa 1.0 kg/cm2980.665
kPa 10.0 torr 1.333223684
MPa 10000.0 atm 1013.25
mmHg @ 0°C 1.333223874 psi 68.94757293
cmHg @ 0°C 13.33223874 lb/ft20.4788025898
mHg @ 0°C 1333.223874 inH2O @ 4°C 2.4908891
inHg @ 0°C 33.86388640341 inH2O @ 20°C 2.486413
mmH2O @ 4°C 0.0980665 inH2O @ 60°F 2.487641558
cmH2O @ 4°C 0.980665 ftH2O @ 4°C 29.8906692
mH2O @ 4°C 98.0665 ftH2O @ 20°C 29.836983
mmH2O @ 20°C 0.097890364 ftH2O @ 60°F 29.8516987

18 ADTS542F/552F/553F/554F User Manual
K0553 Revision C