GEA VARIVENT FRS User manual

Hygienic valves
GEA VARIVENT® FRS valve
Operating instruction (Translation from the original language)
430BAL013059EN_7

COPYRIGHT
These Operating Instructions are the English translation of the original operating
instructions in the sense of the EU Machinery Directive. This document is
protected by copyright. All rights reserved. The document may not, in whole or in
part, be copied, reproduced, translated or reduced to an electronic medium of
machine-readable form without the express permission of GEA Tuchenhagen
GmbH.
LEGAL NOTICE
Word marks
The designations VARIVENT® and T.VIS® are protected trademarks of GEA
Tuchenhagen GmbH.
430BAL013059EN_7
2 24.03.2022

TABLE OF CONTENTS
1 General Information 5
1.1 Information on the Document 5
1.1.1 Binding Character of These Operating Instructions 5
1.1.2 Notes on the Illustrations 5
1.1.3 Symbols and Highlighting 5
1.2 Manufacturer address 6
1.3 Contact 6
1.4 EU Declaration of Conformity in accordance with the EC Machinery Directive 2006/42/EC 7
1.5 Translated copy of the EU - Declaration of conformity in accordance with the Pressure Equipment Directive
2006/42/EU 8
2 Safety 9
2.1 Intended use 9
2.1.1 Requirements for operation 9
2.1.2 Pressure equipment directive 9
2.1.3 ATEX directive 9
2.1.4 Improper operating conditions 10
2.2 Operator’s Duty of Care 10
2.3 Subsequent changes 11
2.4 General safety instructions and dangers 11
2.4.1 Principles for safe operation 11
2.4.2 Environmental Protection 12
2.4.3 Electrical Equipment 12
2.5 Supplementary Regulations 12
2.6 Qualification of personnel 12
2.7 Safety equipment 14
2.7.1 Signage 14
2.8 Residual dangers 15
2.9 Danger zones 16
3 Description 18
3.1 Design 18
3.2 Functional description 20
3.2.1 Installation position 20
3.2.2 Closing Direction 20
4 Transport and storage 21
4.1 Storage conditions 21
4.2 Transport 21
4.2.1 Scope of supply 21
5 Technical data 22
5.1 Type plate 22
5.2 Technical data 22
5.3 Resistance and permitted operating temperature of the sealing materials 23
5.4 Pipe ends - General table of measurements 24
5.5 Tools 25
5.6 Lubricants 25
5.7 Weights 25
6 Assembly and installation 27
6.1 Safety instructions 27
6.2 Notes on installation 27
6.3 Valve with Detachable Pipe Connection Elements 27
6.4 Valve with Welded Ends 28
6.5 Pneumatic connections 28
6.5.1 Air Requirement 29
6.5.2 Establishing Hose Connections 29
6.6 Electrical connections 29
7 Start-up 31
7.1 Safety instructions 31
7.2 Notes on commissioning 31
7.3 Use of the valve in potentially explosive areas 31
8 Operation and control 33
430BAL013059EN_7
24.03.2022 3

8.1 Safety instructions 33
9 Cleaning 34
9.1 Cleaning 34
9.1.1 Cleaning Process Examples 34
9.1.2 Cleaning effect 34
9.2 Passivation 35
10 Maintenance 36
10.1 Safety instructions 36
10.2 Inspections 37
10.2.1 Product contact seals 37
10.2.2 Pneumatic connections 37
10.2.3 Electrical connections 37
10.2.4 Signs on the valve 38
10.3 Maintenance intervals 38
10.4 Prior to disassembly 38
10.5 Disassembling Valve FRS 39
10.5.1 Remove clamp connection (14), separate valve insert from housing 39
10.5.2 Open drive unit 40
10.5.3 Disassembling the Valve into Individual Parts 41
10.5.4 Removing the rinsing valve C 43
10.6 Maintenance 43
10.6.1 Cleaning the Valve 43
10.6.2 Replacing Seals 44
10.6.3 Lubricating Seals and Threads 46
10.7 Installation 47
10.7.1 Torques for the Clamps and Clamp Connections 47
10.7.2 Connections and Operation 48
10.7.3 Pneumatic connection 49
Pneumatic connection Solenoid valve 5/2 way 24VDC 49
10.7.4 Electrical connections 50
Electrical 24 V DC Wiring 50
Electrical Wiring of AS-Interface 51
Setting the feedback 51
Establishing Hose Connections 52
10.7.5 Checking the function 52
11 Alarms 54
11.1 Malfunctions and remedies 54
12 Decommissioning 55
12.1 Safety instructions 55
12.2 Disposal 55
12.2.1 General notes 55
13 Spare parts list - VARIVENT® FRS Valve 56
14 Dimension sheet - Valve FRS 65
15 Appendix 67
15.1 Lists 67
15.1.1 Abbreviations and terms 67
430BAL013059EN_7
4 24.03.2022

1 General Information
1.1 Information on the Document
The present Operating Instructions are part of the user information for the
product. The Operating Instructions contain all the information you need to
transport, install, commission, operate and carry out maintenance for the product.
1.1.1 Binding Character of These Operating Instructions
These Operating Instructions contain the manufacturer's instructions to the
operator of the product and to all persons who work on or use the product
regarding the procedures to follow.
Carefully read these Operating Instructions before starting any work on or using
the product. Your personal safety and the safety of the product can only be
ensured if you act as described in the Operating Instructions.
Store the Operating Instructions in such a way that they are accessible to the
operator and the operating staff during the entire life cycle of the product. When
the location is changed or the product is sold make sure you also provide the
Operating Instructions.
1.1.2 Notes on the Illustrations
The illustrations in these Operating Instructions show the product in a simplified
form. The actual design of the product can differ from the illustration. For detailed
views and dimensions of the product please refer to the design documents.
1.1.3 Symbols and Highlighting
In these Operating Instructions, important information is highlighted by symbols
or special formatting. The following examples illustrate the most important types
of highlighting.
Danger
Warning: Fatal Injuries
Failure to observe the warning can result in serious damage to health, or
even death.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Warning: Explosions
Failure to observe the warning can result in severe explosions.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
General Information
Information on the Document
430BAL013059EN_7
24.03.2022 5

Warning!
Warning: Serious Injuries
Failure to observe the warning can result in serious damage to health.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Caution!
Warning: Injuries
Failure to observe the warning can result in minor or moderate damage to
health.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Notice
Warning: Damage to Property
Failure to observe the warning can result in serious damage to the
component or in the vicinity of the component.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Carry out the following steps: = Start of a set of instructions.
1. First step in a sequence of operations.
2. Second step in a sequence of operations.
®Result of the previous operation.
®The operation is complete, the goal has been achieved.
Hint!
Further useful information.
1.2 Manufacturer address
GEA Tuchenhagen GmbH
Am Industriepark 2-10
21514 Büchen
1.3 Contact
Tel.:[phone]
Fax:[phone]
[email protected]
www.gea.com
General Information
Manufacturer address
430BAL013059EN_7
6 24.03.2022

1.4 EU Declaration of Conformity in accordance with the EC Machinery Directive
2006/42/EC
General Information
EU Declaration of Conformity in accordance with the EC Machinery Directive 2006/42/EC
430BAL013059EN_7
24.03.2022 7

1.5 Translated copy of the EU - Declaration of conformity in accordance with the
Pressure Equipment Directive 2006/42/EU
Manufacturer: GEA Tuchenhagen GmbH
Am Industriepark 2-10
21514 Büchen
We hereby declare that the machine named below
Designation: Valve with actuator
Type: VARIVENT®
due to its design and construction as well as in the versions sold by us, meet the basic safety and health requirements of the following
guideline:
Relevant EC directives: 2006/42/EC EC Machinery Directive
Applicable harmonized standards, in
particular:
EN ISO 12100: 2010
Remarks: •This declaration will become invalid if any alterations are
made to the machine which have not been agreed with us
•We also declare that the relevant technical documentation for
this machine has been prepared in accordance with Annex
VII, Part A, and agree to submit the documentation on
justified request of national authorities on a data carrier
Person authorised for compilation and handover of technical
documentation:
GEA Tuchenhagen GmbH
CE Documentation Officer
Am Industriepark 2-10
21514 Buchen, Germany
Büchen, 24 January 2020
Franz Bürmann
Managing Director i.V. Matthias Südel Head of Engineering
General Information
Translated copy of the EU - Declaration of conformity in accordance with the Pressure Equipment Directive 2006/42/EU
430BAL013059EN_7
8 24.03.2022

2 Safety
2.1 Intended use
The VARIVENT® FRS valve is designed for use with powdery media as well as
CIP and drying processes. The powder medium is conveyed through the process
housing with the valve closed. By means of flush bores, preferably sterile
compressed air that flows through a gap in the valve disk to the process housing,
can be applied to the valve seat. Thanks to this pressurisation any collection of
powder at the valve seat can be avoided.
When the valve is open, cleaning medium can be fed via the single-spout CIP
housing. After the CIP cleaning has been carried out, the valve can be dried in
open valve position with hot air or steam (see “Technical data” (page 21).
The FRS valve is used for opening and closing pipeline sections.
Hint!
The manufacturer will not accept any liability for damage resulting
from any use of the valve which is not in accordance with the
designated use of the valve. The risk of such misuse lies entirely with
the operator of the facility.
2.1.1 Requirements for operation
The prerequisite for reliable and safe operation of the component is proper
transportation and storage as well as professional installation and assembly.
Operating the unit within the limits of its designated use also involves adhering to
the operating, inspection and maintenance instructions.
2.1.2 Pressure equipment directive
The component is a piece of pressure equipment (without safety function) in the
sense of the pressure equipment directive 2014/68/EU. Classified according to
Annex II in category 1.
According to the scope of directive 2014/34/EC, article 1, paragraph 2, f, the
exception of the directive applies, due to conformity with the machine directive
2006/42/EU.
The nominal diameters smaller than DN 25 are subject to article 4, paragraph 3
of the Pressure Equipment Directive which specifies sound engineering practice.
Nominal diameters ≥ IPS 4“; DN 125 valid for the fluid group II.
In the event of any deviations, GEA Tuchenhagen GmbH will supply a specific
Declaration of Conformity.
2.1.3 ATEX directive
In areas with an explosive atmosphere, only valves suitable for use in such areas
may be used.
Please observe chapter 7.3 “Use of the valve in potentially explosive
atmospheres”.
Safety
Intended use
430BAL013059EN_7
24.03.2022 9

If these valves are used in areas with a potentially explosive atmosphere, you
must absolutely comply with directive 2014/34/EC with respect to all ignition
hazards.
2.1.4 Improper operating conditions
The operational safety of the component can not be guaranteed under improper
operating conditions. Therefore avoid improper operating conditions.
The operation of the component is not permitted if:
•Persons or objects are in the danger zone.
•Safety devices are not working or were removed.
•Malfunctions have been detected on the component.
•Damage to the component has been detected.
•Maintenance intervals have been exceeded.
2.2 Operator’s Duty of Care
The operating company of the component has a special responsibility for the
proper and safe handling of the component within their company. Only use the
component when it is in perfect operating condition in order to prevent danger to
persons and property.
This operating manual contains information that you and your employees need
for safe operation over the life of the component. Be sure to read these Operating
Instructions carefully and ensure that the measures described here are observed.
The operator's duty of care includes planning the necessary safety measures and
monitoring that these measures are observed. The following principles apply:
•Only qualified personnel may work on the component.
•The operating company must authorize personnel to carry out the relevant
tasks.
•Order and cleanliness must be maintained at the work stations and in the
entire area surrounding the component.
•Personnel must wear suitable work clothing and personal protective
equipment. As the operating company must ensure that work clothing and
personal protective equipment are used.
•Inform personnel regarding any properties of the product which might pose a
health risk and the preventative measures to be taken.
•Have a qualified first-aid representative on call during the operation. This
person must be able to initiate any necessary first-aid measures in case of an
emergency.
•Clearly define procedures, competences and responsibilities for those
working in the area of the component. Everybody must know what to do in
case of an emergency. Instruct the staff in this respect at regular intervals.
•The signs on the component must always be complete and easy to read.
Check, clean and replace the signs as necessary at regular intervals.
Safety
Operator’s Duty of Care
430BAL013059EN_7
10 24.03.2022

•Observe the Technical Data specified and the limits of use!
Hint!
Carry out regular checks. This way you can ensure that these
measures are actually observed.
2.3 Subsequent changes
No technical modifications should ever be made to this component. Otherwise
you will have to undergo a new conformity process in accordance with the EC
Machinery Directive on your own.
In general, only original spare parts supplied by GEA Tuchenhagen GmbH
should be fitted. This ensures that the component is always operating properly
and efficiently.
2.4 General safety instructions and dangers
The component is safe to operate. It was built according to state-of-the-art
science and technology.
Nevertheless, dangers can arise from the component, if:
•the component is not used as intended
•the component is used improperly
•the component is operated under impermissible conditions
2.4.1 Principles for safe operation
Dangerous situations during operation can be avoided by safety-conscious and
proactive behaviour of the staff.
To ensure safe operation of the valve the following principles apply:
•The Operating Instructions must be kept ready to hand at the valve's place of
use. They must be complete and in clearly legible form.
•Only use the valve for its intended use.
•The valve must be functional and in good working order. Check the condition
of the valve before starting work and at regular intervals.
•Wear tight-fitting work clothing for all work on the valve.
•Ensure that nobody can get hurt on the parts of the valve.
•Immediately report any faults or noticeable changes on the valve to the
person responsible.
•Never touch the pipes and the valve when these components are hot! Avoid
opening the valve unless the process plants have been emptied and
depressurised.
•Observe the accident prevention regulations and all local regulations.
Safety
Subsequent changes
430BAL013059EN_7
24.03.2022 11

2.4.2 Environmental Protection
Harm to the environment can be avoided by safety-conscious and proactive
behaviour of the staff.
For environmental protection the following principles apply:
•Substances harmful to the environment must not be discharged into the
ground or the sewage system.
•Always observe the pertinent regulations relating to waste avoidance,
disposal and utilization.
•Substances harmful to the environment must be collected and stored in
suitable containers. Clearly mark the containers.
•Dispose of lubricants as hazardous waste.
2.4.3 Electrical Equipment
For all work on electrical equipment, the following principles apply:
•Access to electrical equipment should only be allowed to qualified
electricians. Always keep unattended switch cabinets locked.
•Modifications of the control system can affect the safe and reliable operation.
Modifications are only permitted with the express permission of the
manufacturer.
•After completion of all work, check that the protective devices are fully
functional.
2.5 Supplementary Regulations
In addition to the instructions in this documentation the following also has to be
observed:
•pertinent accident prevention regulations,
•generally accepted safety rules,
•national regulations applicable in the country of use,
•work and safety instructions applicable in the facility,
•installation and operating regulations for use in potentially explosive areas.
2.6 Qualification of personnel
This section provides information on how the personnel working on the
component must be trained.
Operating and maintenance personnel must
•have the necessary qualification to carry out their tasks,
•be instructed with regard to possible dangers,
•know and observe the safety instructions given in the documentation.
Only allow qualified electricians to carry out work on the electrical equipment or
have a qualified electrician supervise the work.
Safety
Supplementary Regulations
430BAL013059EN_7
12 24.03.2022

Only allow specially trained personnel to carry out work on an explosion-
protected system. When working on explosion-protected equipment observe the
standards DIN EN 60079-14 for gases and DIN EN 50281-1-2 for dusts.
The following minimum qualifications are required:
•Training as a specialist for working independently on the component.
•Adequate instruction to work on the component under the supervision and
guidance of a trained specialist
Each employee must meet the following requirements to work on the component:
•Personal suitability for the respective task.
•Sufficient professional qualification for the respective task.
•Received instruction about the functionality of the component.
•Received instruction about operating sequences on the component.
•Familiar with the safety devices and their function.
•Familiar with these Operating Instructions, especially with the safety
instructions and the information which is relevant for the task on hand.
•Familiar with the basic regulations with regard to occupational health and
safety and accident prevention.
When working with the component, a distinction is made between the following
user groups:
Safety
Qualification of personnel
430BAL013059EN_7
24.03.2022 13

User groups
Staff Qualifications
Operating personnel Adequate instruction and sound knowledge in the following areas:
•Functionality of the component
•Operating sequences on the pump
•What to do in case of an emergency
•Lines of authority and responsibilities with respect to the task
Maintenance personnel Appropriate training and a sound knowledge of the structure and
functionality of the component.
Sound knowledge in the following areas:
•Mechanical equipment
•Electrical equipment
•Pneumatic system
Authorization with regard to safety engineering standards to carry
out the following tasks:
•Setting devices into operation
•Earthing of devices
•Marking of devices
The relevant certificates of qualification must be submitted before
work can be carried out on ATEX certified machines.
2.7 Safety equipment
2.7.1 Signage
Dangerous points on the valve are indicated by warning signs, prohibition signs
and mandatory signs.
The signs and notes on the valve must always be legible. Any illegible signs must
be replaced immediately.
Safety
Safety equipment
430BAL013059EN_7
14 24.03.2022

Signs on the valve
Sign Meaning
Fig.1
General hazard warning
Fig.2
Warning Crushing
Fig.3
Explosive atmosphere hazard warning
2.8 Residual dangers
Dangerous situations can be avoided by safety-conscious and proactive
behaviour of the personnel and by wearing personal protective equipment.
Residual dangers on the valve and measures
Danger Cause Measure
Danger to life Inadvertent switch-on of the
valve
Effectively disconnect all components, effectively prevent switch-
on.
Electric power Observe the following safety rules:
1. Isolate from the power supply.
2. Take appropriate measures to prevent switch on.
3. Test absence of voltage.
4. Earthing and short-circuiting.
5. Cover or safeguard any adjacent live parts.
Safety
Residual dangers
430BAL013059EN_7
24.03.2022 15

Residual dangers on the valve and measures
Danger Cause Measure
Risk of injury Danger presented by moving or
sharp-edged parts
The operator must exercise caution and prudence.
For all work:
•Wear suitable work clothing.
•Never operate the machine if the cover panels are not
correctly fitted.
•Never open the cover panels during the operation.
•Never reach into openings.
As a precautionary measure, wear personal protective equipment
in the vicinity of the valve:
•Protective gloves
•Safety shoes
Environmental damage Operating materials with
properties which are harmful to
the environment
For all work:
•Collect lubricants in suitable containers.
•Dispose of lubricants in accordance with the pertinent
regulations.
2.9 Danger zones
Please observe the following notes:
Fig.4
•In the event of malfunctions, shut down the valve (disconnect from the power
and air supply) and secure it against being used.
•Never reach into the valve housing (1) when the valve is switching. Fingers
can be crushed or cut off.
•If the valve is installed in hanging installation position, there is the risk that the
valve insert including drive falls out of the housing. Therefore secure the valve
prior to undoing the hinged ring (14) against falling with a suitable lifting
device. Ensure that you always wear safety shoes.
Safety
Danger zones
430BAL013059EN_7
16 24.03.2022

•Before starting any service, maintenance or repair work, disconnect the valve
from the power supply and secure it against inadvertently being switched
back on again.
•Only allow a qualified electrician to carry out any work on the electrical power
supply.
•Check the electrical equipment of the valve at regular intervals. Immediately
remedy loose connections and molten cables.
•If work on live parts cannot be avoided, call in a second person, who can
operate the main switch in case of an emergency.
•The housing nozzle and the valve disk have very sharp edges. When
transporting and assembling the valve be sure to wear suitable protective
gloves.
Safety
430BAL013059EN_7
24.03.2022 17

3 Description
3.1 Design
Fig.5
Design
No. Designation
1 Housing combination
2 Sealing ring
3 Lantern
4 Spacer
5 Cylinder cover
6 Valve disk
7 Piston
8 Piston rod
9 Leadership
10 Cap
13 Circlip
14 Clamp connection
17 Cylinder screw hex socket
19 Guide ring
20 V-ring
21 O-ring piston rod seal
22 O-ring piston
Description
Design
430BAL013059EN_7
18 24.03.2022

Design
No. Designation
23 O-ring piston
24 O-ring piston rod seal
25 O-ring hood seal
41 Flush valve
Description
Design
430BAL013059EN_7
24.03.2022 19

3.2 Functional description
3.2.1 Installation position
Installation position: The valve is usually installed in hanging position (overhead).
3.2.2 Closing Direction
Closing direction: in hanging installation position from bottom to top, air opening
and air closing
Fig.6
Description
Functional description
430BAL013059EN_7
20 24.03.2022