Goldmedal 2365 User manual

Nacho Cheese Warmer
Instruction Manual
Model #2365 and Model #2365LS
PartNo.38409
RevisedJune 1996
Cincinnati, OH 45241-4807 USA
Model #2365
Model #2365LS

SAFETY PRECAUTIONS

Nacho Cheese Warmer
MODELS #2365 AND #2365LS
1
INSTALLATION
CHECKING SHIPMENT
Unpack shipping carton and check thoroughly for any damage which may have occurred during
transit. Claims should be filed immediately with the transportation company.
ELECTRICAL REQUIREMENTS
Your condiment warmer is 120 volts, 60 cycle and will draw a maximum of 3 amps. A 15 amp
grounded circuit is required for 120 volts.
OPERATING INSTRUCTIONS
1. Fill water well to the bottom of the “water level“ ring.
2. Insert the cheese bowl into the water.
3. Install the cover and ladle into the top of the cheese bowl insert.
4. Plug the unit into the wall socket.
5. Set control knob to 150º F setting.
6. Let cheese heat for 45 minutes (stirring every 15 minutes) before serving.
7. Turn heat control switch to “OFF” position when unit is not in use.
The unit machine must be properly grounded to prevent
electrical shock.
The warmer
should not
be operated
without
water in the
well.

Nacho Cheese Warmer
MODELS #2365 AND #2365LS
2
CARE AND CLEANING
Clean your machine daily. A clean well kept machine is one of the best
ways of advertising your product.
Use a mild soap and damp cloth to clean the exterior of the unit.
All utensils and the insert bowl should be cleaned with a sanitizing solution to help prevent con-
tamination from micro-organisms.
LIGHT BULB & SIGN REPLACEMENT
1. Remove the cheese bowl insert from the unit.
2. Remove the water from the machine.
3. Remove the two screws that hold the retaining angle.
4. Slide the sign out from the bottom.
5. Remove the bulb from the socket and replace as necessary.
6. Clean all interior surfaces before re-assembly.
7. Reinstall the sign and retaining angle. Re-install the two screws.
Unplug the machine before cleaning. Do not immerse the
unit in water.
Unplug the machine before servicing.

Nacho Cheese Warmer
MODELS #2365 AND #2365LS
3
HEAT ELEMENT & THERMOSTAT REPLACEMENT
1. Remove the cheese bowl insert.
2. Turn the unit upside down.
3. Remove the screws from the bottom of the unit. It is not necessary to remove the rubber
feet.
4. Unfasten the thermostat screw and the two screws from the heating element.
5. Disconnect the wires from the thermostat and heating element.
6. Replace unserviceable parts and rewire as shown in the wiring diagram.
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN-
TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO
ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
Do NOT immerse the equipment in water.
Unplug your machine before servicing.

Nacho Cheese Warmer
MODELS #2365 AND #2365LS
4
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4.Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [email protected]

Nacho Cheese Warmer
MODELS #2365 AND #2365LS
5
CABINET ASSEMBLY

Nacho Cheese Warmer
MODELS #2365 AND #2365LS
6
PARTS LIST - CABINET ASSEMBLY
Model Model
#2365 #2365LS
Item No. Part No. Part No. Description
1 22038 22038 Lead In Cord
2 38034 38034 Label, Caution Water Level
3 38077 38077 Socket, Lamp Holder
4 38227 38227 Thermostat
5 38272 38272 Light Baffle
6 38279 38279 Tank Heat Element
7 n/a 38284 Sign Cover
8 38291 38291 Lamp, 6 Watt White
9 38294 38294 Insulation Wrap
10 38295 38295 Insulation Bottom
11 38297 39297 Retaining Angle
12 38303 38303 Temperature Scale
13 38389 38389 Knob, Heat Control
14 38417 38417 Well Body, Welded Assembly
15 38419 38419 Panel, Control
16 38420 38420 Label, Fill to Line
17 n/a 38421 Lighted Cabinet, Welded Assembly
18 38403 n/a Unlighted Cabinet, Welded Assembly
19 n/a 38423 Bottom Cover, Lighted
20 38418 n/a Bottom Cover, Unlighted
21 40324 40324 Switch, Rocker
22 40353 40353 Wire Nut, Black
23 42828 42828 Sheet Metal Screw
24 47010 47010 Label, Safe
25 47300 47300 Tinnerman Fastener
26 74119 74119 Warning, Disconnect Power
27 n/a n/a
28 76026 76026 Strain Relief, Cord
29 82189 82189 Label, Max. Lamp
30 87149 87149 Label, Caution Disconnect
31 87223 87223 Sleaving, Fiberglass
32 87247 87247 Bumper, Headed Screw

Nacho Cheese Warmer
MODELS #2365 AND #2365LS
7
ELECTRICAL SCHEMATIC

WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, volt-
age, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
ORIMPLIED,ANDOFALLOTHEROBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIP-
TION ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASERFIRSTCALLSGOLDMEDALPRODUCTSCOMPANY AT 1-800-
428-2676 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIP-
MENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERN-
ING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, OH 45241-4807 USA