Goldmedal 5584EX User manual

Nacho Chip Warmer
Instruction Manual
Model #5584EX
PartNo.40558EX
RevisedJune 1996
Cincinnati, OH 45241-4807 USA
BACK TO INDEX

SAFETY PRECAUTIONS
NOTE
The information, specifications and illustrations contained in this manual represent
the latest data available at time of publication. Right is reserved to make changes as
required at the discretion of Gold Medal Products Company without notice.
Any alterations to this equipment will void the warranty and
may cause a dangerous situation. NEVER make alterations
to the equipment.
Always wear safety glasses when servicing this equipment.
Machine must be properly grounded to prevent electrical shock
to personnel.
Do NOT immerse the equipment in water.
Always unplug the equipment before cleaning or servicing.
This equipment is designed and sold for commercial use only. This
equipment is not to be used by the consumer in home use. Do not allow
direct contact of this equipment by the public when used in food service
locations. Only personnel trained and experienced in the equipment
operation may operate this equipment.
Carefully read all installation instructions before operating the equipment.
NEVER put your fingers or any object into the heating area.
We do NOT assume any liability for injury due to careless
handling or operation of this equipment.

Nacho Chip Warmer
EXPORT MODEL #5584
1
CAUTION
FORWARD
This instruction manual and parts listing covers the following models:
5584EX Nacho Chip Warmer.
Clean your nacho chip warmer thoroughly upon arrival to remove any debris left from manufac-
turer (see “CARE AND CLEANING” instructions).
CHECKING SHIPMENT
Your new Chip Warmer is shipped completely assembled, ready to operate. After removing the
corrugated carton from the machine, check thoroughly for any damage which may have occurred
in transit. Claims should be filed immediately with the transportation company.
ELECTRICAL REQUIREMENTS
MODEL NO. VOLTS AMPS WATTS HERTZ
5584EX 230 .37 86 50
A rocker switch on the bottom of the unit controls both the heater and light bulb. The heat ele-
ment on the underside of the chip warmer keeps nacho chips warm and fresh in the cabinet. A
yellow shatterproof light bulb also serves as to warm the nachos while illuminating the inside of
the cabinet.
LOADING PRODUCT
To load your Nacho Chip Warmer, open the front door and pour in the nacho chips. For the best
display, fill your warmer ¾ full.
Machine must be properly grounded to prevent shock in case of
electrical problems.
When replacing the 11 watt yellow light bulb, do not use a larger
watt bulb or a bulb that is not shatterproof.

Nacho Chip Warmer
EXPORT MODEL #5584
2
CARE AND CLEANING
Your Nacho Chip Warmer is constructed of a all stainless steel cabinet and a tempered front
glass. When your unit becomes dirty usually a damp cloth will remove all dirt and grease spots.
A sanitary cleaner can be used to remove stubborn areas. The front tempered glass window
should be kept clean for easy viewing of your nacho chips.
Do not immerse the machine in water! The heating element and
wiring were not designed for immersion, water will ruin the heater
and cause short circuits in the wiring.

Nacho Chip Warmer
MODEL#5584
3
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4.Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [email protected]
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN-
TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO
ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
Do NOT immerse the equipment in water.
Unplug your machine before servicing.

Nacho Chip Warmer
EXPORT MODEL #5584
4
CABINET ASSEMBLY

Nacho Chip Warmer
EXPORT MODEL #5584
5
Item No. Part No. Description
1 40012 Porcelain Socket
2 n/a 11 Watt Light Bulb, Coated
3 40902 Heat Transfer Plate
4 40554 Cabinet Weld Assembly
5 40563 Glass, Tempered
6 40567 Glass Channel, 292,1mm
7 40568 Glass Channel, 174,6mm
8 n/a Strip Heater, 50 Watt
9 40324 Rocker Switch
10 47120 Knob, Door
11 40562 Door, Plastic
12 40570 Hinge, with Stud
13 n/a Lead-in Cord
14 38439 Bottom Plate
15 40564 Glass Retainer Bracket
16 41314 Screw, 10-24 x 19mm (4)
17 87179 Glide Foot
18 49123 Crutch Tip
19 38450 Thermostat
ITEMS NOT SHOWN
10162 Screw, 8-32 x 12,7mm (6)
40569 Acorn Nut, 10-32
87194 Strain Relief, Power Cord
PARTS LIST - CABINET ASSEMBLY

Nacho Chip Warmer
EXPORT MODEL #5584
6
ELECTRICAL SCHEMATIC

WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, volt-
age, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
ORIMPLIED,ANDOFALLOTHEROBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIP-
TION ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASERFIRSTCALLSGOLDMEDALPRODUCTSCOMPANYAT 1-800-
428-2676 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIP-
MENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERN-
ING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA