Goldmedal 5330 User manual

Part No. 36063
Revised: April 2009
Dual Temperature Warmer
Instruction Manual
Model #5330, 5330FN, 5330EX
Cincinnati, OH 45241-4807 USA

SAFETY PRECAUTIONS

Forward
This manual covers the 5330, 5330FN and 5330EX warmers.
Installation Instructions
Inspection of Shipment:
Unpack all cartons and check thoroughly for any damage that may have occurred during
transit. Damage claims should be filed immediately with the transportation company. Gold
Medal is not responsible for damage that occurs in transit.
Setup:
Your new Warmer is completely assembled and tested at the factory.
Remove all packing material and tape before starting operation.
Electrical Requirements:
The following power supply must be provided:
Model No. 5330, 5330FN: 120 VAC, 60 Hz. 15 amp protected circuit.
Model No. 5330EX: 230 VAC, 50 Hz. 15 amp protected circuit.
Your electrician must furnish sufficient current for proper machine operation. We recommend
this popper be on a dedicated and circuit protected line. Failure to wire properly will void the
warranty and can result in damage to the heat elements, light, motor and etc.
It is Gold Medal Products Company’s recommendation that this machine be plugged directly
into a wall outlet. The use of extension cords is not recommended due to safety reasons and
the popper’s performance will be sacrificed/reduced.
Before You Plug In Machine:
1. Make sure that the wall outlet can accept the three (3) prong grounded plug on the power
supply cord.
2. The wall outlet must have the proper polarity. If in doubt, have a competent electrician
inspect the outlet and correct if necessary.
3. DO NOT use a three (3) prong grounded to two (2) prong un-grounded adapter.

4
Installation
1. Install Graphics
2. Remove (Cut) white cable tie from unit and position the racks in correct position.
Note: Keep black cable ties in place. Top and middle racks are positioned under
rack mount bolts, on the rack supports.
3. Plug power cord into outlet.
4. Turn on power switch on rear of the unit.
5. Pre-heat the unit for approximately ONE hour. The I setting is for LOW warmth and
the II setting is for HIGH warmth.
6. Dispensing temperature for cheese cups is between 125 Deg. F and 140
Deg. F
Note - This unit is only for the warming of the pre packaged FOOD PRODUCTS.
Do not dispense volatile foods.
Operating Instructions
Controls and Their Functions
1. For warming of cheese cups, use only the HIGH warmer setting.
2. Pretzel warming can be done using the HIGH or LOW settings for desired warmth.
3. Other foods may also be warmed using this machine.

5
Care and Cleaning
Cleaning Guidelines
The plastic exterior of the Cheese Cup Warmer is easy to keep clean. Usually a damp cloth will
remove all dirt and grease spots. NEVER USE ABRASIVES.
1. Turn power switch to the OFF position. Disconnect the unit from power source.
2. Wipe exterior surface of unit.
3. Wipe interior areas of the unit, confirm the unit is cool and unplugged.
Cleaning Air Intake (weekly)
1. Disconnect Unit from Power supply
2. Use a vacuum cleaner and/or a damp cloth to clean air intake.
3. Position unit for normal operation and reconnect to power source.

6
MAINTENANCE INSTRUCTIONS

7
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include the machine’s model name, serial number, and date of manufacture (located on
the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
[phone]
[phone]
Fax: [phone]
or, place orders at:
E-mail: [email protected]
Web Page: www.gmpopcorn.com

8
Warmer Breakdown
Heater Assembly
p/n 36064
(EX p/n 36064EX)
3 Position Switch
p/n 39410 Thermostat 120°F p/n 36110 Thermostat 140°F p/n 36078
Clear Doo
r
p/n 36079
Fan - Blowe
r
p/n 36075
(EX p/n 36075EX)
Housing Uppe
r
p/n 36071 Housing Base
p/n 36070

9
Electrical Schematic

10
© The text, descriptions, graphics and other material in this publication are the proprietary
and exclusive property of Gold Medal Products Company and shall not be used, copied,
reproduced, reprinted or published in any fashion, including website display, without its
express written consent.
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage,
abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA
www.gmpopcorn.com
Phone: [phone]
Fax: [phone]