Goldmedal 8018 User manual

Part No. 87794
Revised: October 2004
BUN WARMER
Instruction Manual
Models:8018,8019,8117,8219,8170
Cincinnati, OH 45241-4807 USA

Bun Warmers
2 Models: 8018,8117,8019,8219,8170
SAFETY PRECAUTIONS

Bun Warmers
3 Models: 8018,8117,8019,8219,8170
INSTALLATION INSTRUCTIONS
Checking Shipment
Unpack carton and check thoroughly for any damage, which may have occurred during transit.
Damage claims should be filed immediately with the transportation company. Remove all tape from the
outside, and inside of the machine.
Electrical Requirements
Your Gold Medal Bun Warmer is designed to operate on a 120 Volt / 15 Amp / single-phase outlet.
Make sure the warmer is on a dedicated line, and that no other appliances are on the same circuit.
OPERATING INSTRUCTIONS
1. Place the bun warmer on a solid, level surface.
2. Plug warmer into an appropriate outlet, following the guidelines set forth above in “Electrical
Requirements.”
3. Open front drawer and remove false bottom.
4. Pour enough water into the drawer insert to cover the bottom of the drawer. Approximately 1/8” deep.
(This provides the humidity to keep the hot dog buns from drying out as they are heated.
5. Replace false bottom, then close the drawer.
6. Turn the temperature dial to 140-160 degrees and allow the unit to preheat for 15-20 minutes.
7. Place desired amount of hot dog buns in drawer pan.
Note: Check for water periodically to ensure proper humidity. The machines water consumption varies with
temperature setting, machine usage, etc. Empty water from drawer, and clean nightly to prevent
product contamination. If machine runs out of water, the hot dog buns will become hard and dried out.

Bun Warmers
4 Models: 8018,8117,8019,8219,8170
CLEANING INSTRUCTIONS
1. Unplug the unit before cleaning or servicing.
2. Open drawer. When drawer is fully open, locate drawer release levers on both sides of the back of the
drawer.
3. Push down on both levers simultaneously and pull drawer completely out of the unit.
4. Remove Drawer pan and false bottom, and wipe down all components using a clean, soft cloth.
5. When dry, clean all stainless steel surfaces (drawer, drawer pan, false bottom, cabinet, etc.) with a
high quality concession cleaner such as Gold Medal’s - Watch Dog Concession Equipment
Cleaner, item #2580.
6. Re-assemble drawer components using the above steps for a reference.

Bun Warmers
5 Models: 8018,8117,8019,8219,8170
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4.Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
[phone]
Fax: [phone]
E-mail: [email protected]
www.gmpopcorn.com

Bun Warmers
6 Models: 8018,8117,8019,8219,8170
BUN WARMER ASSEMBLY

Bun Warmers
7 Models: 8018,8117,8019,8219,8170
PARTS LIST – BUN WARMERS
Item # Model # Description
8018
8019 8117 8219 8170
1
41033 41033 41033 41033 41033 Pilot Light, 125V - Red
2
87779 87523 87767 88393 88410 Bottom Cover
3
87429 87429 87429 87429 87429 Heat Control
4
87430 87430 87430 87430 87430 Knob, Heat Control
5
87788 87706 87776 88394 88415 Body Weldment
6
87781 87703 87769 87703 88413 Drawer Front Weldment
7
87420 87420 87420 87420 87420 Drawer Handle
8
87428 87428 87428 87428 87428 120V / 300W Heat Element
9
87923 87925 87929 87925 88430 Drawer Weldment
10
87789 87742 87777 87742 88425 Insulation Mat
11
87784 87741 87772 87741 88428 Insulation Pan
12
87763 87763 87763 87763 88437 Element Bracket / Retainer
13
87783 87526 87771 87526 88411 Drawer Rear
14
87778 87527 87766 87527 88412 Cover Panel
15
87527 87522 87522 88382 88409 End Cover
16
87921 87921 87927 87921 88438 Drawer Pan
17
47328 47328 47328 47328 47328 Glide

Bun Warmers
8 Models: 8018,8117,8019,8219,8170
ELECTRICAL SCHEMATIC
Models: 8018, 8117, 8170

Bun Warmers
9 Models: 8018,8117,8019,8219,8170
ELECTRICAL SCHEMATIC
Models: 8019, 8219

Bun Warmers
10 Models: 8018,8117,8019,8219,8170
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage,
abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT
PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING
THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA
www.gmpopcorn.com
Phone: [phone]
Fax: [phone]