Grandview Edge R7 User manual

Edge R7 Fixed Frame Guide
Model：PE-Yxxx(R7)15
PE-Yxxx(R7)12
Ⅲ Frame assembly
a. "Raise the screen, rotate F5 to the correct direction, align with the
installation slot of P2, and press down slightly with a tool. Each frame is
fixed with three P2 (all need to be pressed to the bottom to complete
the fixing)."
b. "Slide the frame to the center and insert P1 into the end face of F5,
then install the adjacent frame."
c. "Connect the plastic corner guard P1 to the frames (F6, F5) in order to
complete the installation of the frame."
P1
Press down
P2
(F5、F6、P1、P2）
P1*4
Ⅳ Wall mount
Back
Front
(F7、S6、S7）
F7
Screen middle line
a. "Flip the screen to ensure the correct orientation (for
ultra-short-throw anti-glare screens). Install S6 in the
upper frame slot (note that the hook should face the
back). The installation spacing A = 0.52 * L."
b. "Attach S7 strong magnets to the sides of S4 at the
bottom and mark them."
c. "Calculate the screen installation position, mark the
highest line of the screen and the vertical centerline.
The highest line of the screen is marked 109mm below
the F7 bottom reference line."
d. "Align F7 with the bottom reference line, mark the
installation hole positions, drill holes, insert expansion
glue particles, and secure with ø5*50 screws."
e. "Two people lift the screen simultaneously and hang
it on the groove of F7. Move it left and right to the
desired position, then mark the position of the strong
magnet. Remove the screen, drill installation holes, insert
expansion glue particles, and secure with ø5*50 screws."
f. "Hang the screen back up, move it left and right to the
magnet position, gently place the screen, and complete
the wall-mount installation of the screen."
UP
Ⅲ/a Ⅲ/b
Ⅲ/c
Ⅲ/a-b
Ⅲ/c-d
Ⅲ/e-f
109
A
L
Screen top line
Screen middle line
109
Thank you for choosing Grandview products. Before installation and use, please read
the instructions carefully and keep them for future reference
Please assemble the screen in a flat and clean area, which is beneficial to protect the
screen fabric and ensure the assembly effect of the frame
The edges of the screen frame are sharp, so please protect your body during assembly
to prevent cuts.
If you have purchased an ultra-short-throw anti-glare screen, please pay attention to
the orientation of the screen during installation.
Reminder
F5 F5
F6 *4
F5 *2
S7
S6
S4
F7

P1
P2(Pre-installed)
Exploded view
Cutaway view
Front
Back
Side
P1
Screen
Diagram
Screen components
"Please check whether all the components of the silver screen are complete before assembly. Some nuts and accessories have been
pre-installed, and the extra screws and accessories are for backup in case of damage during the installation process."
Frame set F
Lock set S
Fabric 1PCS
M5*8 large flat
head screws,
30 pieces
"M5*6 countersunk
screws, 4 pieces
(pre-installed)"
M5 long nut(pre-installed)
P2(pre-installed)P1 4PCS
其它
ⅠInner frame assembly
Back Front
Fabric dismount tools
a. Take F1 and F2 and place them on the left and right side respectively. Merge the two vertical cuts and secure S1 and S2 using M5*8
screws. This completes the assembly of component A.
b. Take two component A and two F3, arrange them to form a rectangle. Insert S3 into the slots at the four corners, adjust until the joint
gap is minimized, then tighten the screws. Take F4 and S5 and place them in the center of the frame, align with the pre-installed nuts,
and tighten all the screws to complete the front connection of the frame.
c. Flip the assembled frame upside down, take S4 and adjust the upper nuts into the corner grooves, tighten the screws to reinforce the
back of the frame, completing the installation of the inner frame.
Ⅱ Fabric installation
Tool
A
A
B
B
C C
Front up
Front
Installation method
C
C
A
A
A
A
A
A
B
C
C
BC C
Press down
Align
Apply force
Fabric alignment point：A*8→B*4
Edge installation direction
≈10mm
a. Flip the frame over so that the front side faces up. Place the screen fabric on the highest surface of the frame and rotate the winding pipe to completely
flatten the screen fabric.
b. Pull the screen fabric outwards and use it to completely cover the frame, aligning the screen fabric with the frame.
c. This screen fabric installation method is a card strip type, which requires a special tool to be used to press the inner edge of the card strip into the sawtooth
groove of the frame to fix the screen fabric.
d. Installation details: gently press the tool head into the sawtooth groove at the edge of the screen fabric by about 10mm (using the first or second level
sawtooth groove). The installation sequence is to first press point A in the four corners, then point B in the middle to initially position the screen fabric, and
then press the remaining edge C from the center outwards to fix the screen fabric.
e. Flatness adjustment: If it is found that the tension of the screen fabric is insufficient after it is fixed, use a tool to press the card strip down to increase
tension on the screen fabric.
(F1、F2、F3、F4、S1、S2、S3、S4、S5)
Ⅰ/a Ⅰ/b Ⅰ/c
Ⅱ/a Ⅱ/b
Ⅱ/c Ⅱ/d-e
29
12or15mm
109
67
Flatten up and align
Glove (2 sets) Ø5X50mm countersunk
self-tapping screws, plastic
expansion tube
(total of 8 pieces)"
F1+F6 2PCS
F2+F6 2PCS F3+F5 2PCS F7 1PCS
S1 2PCS S2 2PCS S3 4PCS S4 4PCS
S5 2PCS（pre-installed） S6 2PCS S7 2PCS
Fabric
F1
F6 F2
F3
F4
F5
F7
F5 F4
F1 F2
F3
F4
F6
S2
S1
S3
S4
S5
S6
S7
S1S4 S6
S3S2
S7
Back
S4 *4
F3*2
S3 *4
Part A*2
Front
Adjust
F4 + S5 1~2PCS
Protection mat
F1
F2
S2
Part A
S1 F4 + S5
Accoustic transparent fabric
"When you choose woven acoustically transparent
screen fabric, you need to install the black acoustically
transparent fabric. Simply use the pre-installed Velcro
to attach the acoustically transparent fabric to cover
the frame."