Great Little Trading Lulworth User manual

1
Lulworth Chest of Drawers
12/07/2021
V1
one-person job
Assembly Difculty
easy - medium - hard
A few important pointers before you start:
• Please read the instructions right through before you start, and
check that all the components have been included in the pack;
we nd separating all the hardware into piles makes it easier to
be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided
if required, but screw drivers and other tools are not.You’ll
nd details of the tools you need at the beginning of the
instructions.
• It’s a good idea to build the unit in the room where you are
going to be using it, to avoid the need to move it after it’s been
assembled.
• Do not throw away any packing materials until assembly is
complete, just in case you accidentally discard smaller parts or
hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.

2
Safety Warnings:
• PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
• Adult assembly required.
• In an unassembled state product contains small parts which may pose a
choking hazard, not suitable for children under 3 years.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• To avoid possible injury from tipping, DO NOT allow children to climb
on the product.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over. Ensure you secure this
furniture product to the wall before you use it, using the kit provided.
• If you have not received an anti-tip kit with your product please contact
Customer services.
• Check all xtures and ttings regularly and tighten as necessary.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
• Regularly check all fastenings, xtures and ttings to ensure that they
are properly tightened.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
E F
G H
I J
1x Top Drawer Divider Panel 4x Drawer RH Sides
2x Large Drawer Base Panels
1x LH Small Drawer Front 2x Small Drawer Base Panels
2x Small Drawer Back Panels
1x RH Small Drawer Front
2x Large Drawer Back Panels
1x LH Side Panel
1x Base Panel
2x Back Panels
2x Large Drawer Fronts 4x Drawer LH Sides
1x Top Panel
1x RH Side Panel
1x Horizontal Divider Panel
K L
M N
O P
Q
Component Check List Component Check List
4x Feet

4
Hardware Check List Hardware Check List
#1 #11
#3 #13
#5 #15
#7 #17
#9
#2 #12
#4 #14
#6 #16
#8
#10 You will need
(not supplied)
Philips Head Screwdriver
4x Flat Runners
4x Flat Runners
16x Wooden Dowels
(20mm)
26x Cam Dowels
4x Hex Bolts
(42mm)
4x Flat Runners 12x Screws
(16mm)
6x Flat-Ended Screws
4x Cross-Head Bolts
(47mm)
48x Screws
(12mm)
6x Handles
4x Barrel Nuts
1x Allen Key 1x Anti-tip Kit
4x Flat Runners
18x Screws
(25mm)
26x Cam Locks
4x Wooden Dowels
(25mm)

5
STEP 2:
Note: You will be building this unit with the back facing up.
Align horizontal divider panel (B) so that the countersunk holes in the
middle of the panel are facing outwards and the 2x small pilot holes on
the long thin edge are facing up.
Insert 2x wooden dowels (#5) into the inner holes on the edge of panel
(A) and slot into panel (B) ensuring that the wheels of the runners are
facing the oor and that runner (#1) is on the left-hand side as shown.
Secure panels together using 2x screws (#6) through panel B.
Hardware for Step 1:
Hardware for Step 2:
1x #1 Flat Runner
1x #2 Flat Runner
6x #12 Screws (12mm)
2x #6 Screws (25mm)
STEP 1:
Working on a protective surface like a carpet or a rug, take panel (A) and
attach at runner (#2) as shown in position 1 with 3x screws (#12). Flip
panel (A) so that it is in position 2 and attach at runner (#1) as shown
with 3x screws (#12).
Note: Ensure that the screws attaching the runners are fully secured and lie at
to allow the drawer to run smoothly.
When in the correct position, the runner wheel will be at the front edge of the
panel.
2x #5 Wooden Dowels (20mm)
#12
#12 #12
#12 #12
#12 #12
#12
#12
#12
#12
#12
#1
#2
#1
#1
A
A
A
B
#6
#6
#5
#5
#2
POSITION 1 POSITION 2
The small drill holes on the
edge of Panel B to be facing up.

6
STEP 3:
Take the LH side panel (C) and attach 3x
at runners (#1) with 3x screws (#12) for
each runner.
When xed in the correct position, there
will be a gap between the front edge of
the panel and the start of the runners. If
the front of runners is level with the edge
of the panel, it is in the wrong position.
Once complete, insert 2x cam dowels
(#7) where indicated.
#1
#1
#1
#1
Hardware for Step 4:
2x #5 Cam Dowels
2x #8 Cam locks
STEP 4:
Insert 2x wooden dowels (#5) into side
panel (C) in the inner holes next to the
cam dowels (#7).
Now attach side panel (C) to the right-hand
side of divider panel (B). Ensure that the
ledged side is facing upwards and that the
wheels of the runners are facing the oor.
Once in position, secure with 2x cam locks
(#8) as shown.
B
C
Hardware for Step 3:
3x #1 Flat Runners
2x #7 Cam Dowels
9x #12 Screws (12mm)
A
#12
#12
#12
#12
#12
#12
#12
#7
#7
#5
#5
#8
#8
#7
#7
#12
C
#12
#12
#12
#12
Using Cam Locks:
When inserting into the panel, ensure
that each cam lock’s arrow is pointing
towards the drill hole on the side edge
of the panel & the dowel that it will be
receiving.
When the panels are in the connected
position, using a screwdriver, turn the
cam lock in a clockwise direction to
lock and secure.
Use the smaller holes when
attaching the runner. Start
with the rst small next to the
wheel.
TOP
BASE

7
STEP 5:
Take the RH side panel (D) and attach 3x at
runners (#2) with 3x screws (#12) for each
runner.
When xed in the correct position, there will
be a gap between the front edge of the panel
and the start of the runners. If the front of
runners is level with the edge of the panel, it is
in the wrong position.
Insert 2x cam dowels (#7) where indicated.
STEP 6:
Insert 2x wooden dowels (#5) into side panel
(D) in the inner holes next to the cam dowels
(#7).
Now attach side panel (D) to the other side of
divider panel (B). Ensure that the ledged side
is facing upwards and that the wheels of the
runners are facing the oor.
Once in position, secure with 2x cam locks (#8)
as shown.
Hardware for Step 6:
2x #8 Cam Locks
2x #5 Wooden Dowels (20mm)
D
B
D
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#5
#5
#5
#8
#8
#2
#2
#2
#2
#7
#7
Hardware for Step 5:
3x #2 Flat Runners
2x #7 Cam Dowels
9x #12 Screws (12mm)
TOP
BASE
Use the smaller holes when
attaching the runner. Start
with the rst small next to the
wheel.

8
Hardware for Step 8:
6x #7 Cam Dowels
F
E
D
C
STEP 7: Attach base panel (E).
Insert 4x wooden dowels (#5) to the inner
holes in the ends of the side panels (C) and (D)
as shown. Insert 4x barrel nuts (#16) to the
holes on the inside of the side panels, ensuring
the hole in the nut is facing towards the base.
Position the base panel (E) with the recessed
edge facing up and push into position. Fix in
place using 4x cross-head bolts (#15) through
the base into the side panels. Fully tighten using
a Philips screwdriver.
Hardware for Step 7:
4x #16 Barrel Nuts
4x #5 Wooden Dowels (20mm)
4x #15 Cross-Head Bolts (47mm)
STEP 8:
Take top panel (F) and insert 6x cam dowels
(#7) as shown.
#15
#15
#15
#16
#16
#16
#16
#15
#5
#5
#5
#5
#7
#7
#7
#7
#7
#7
TOP
BASE

9
Hardware for Step 9: Hardware for Step 10:
6x #5 Wooden Dowels (20mm)
4x #10 Wooden Dowels (25mm)
6x #8 Cam Locks
4x #9 Hex Bolt (42mm)
#5
#5 #5
#8 #8
#9
#9
#9
#9
#10
#10
#10
#10
#8
#8
#8
#8
A
HE
H
H
H
B
D
F
C
STEP 9:
Insert 6x wooden dowels (#5) into the
remaining holes in top panel (F). Position top
panel (F) onto the unit, aligning the hardware
with panels A, C & D. Ensure that the grooved
edge of top panel (F) is facing up.
When in place, secure panel (F) in position
with 6x cam locks (#8) as shown on panels A,
C & D.
STEP 10: Attach the feet.
Insert 4x wooden dowels (#10) into each
corner of base panel (E) where indicated.
Push the 4x feet (H) into position and, using
the Allen Key provided, attach EACH foot
by inserting 1x hex bolt (#9) through base
panel (E) into the feet.

10
STEP 11:
Take the 2x back panels
(G) and place them within
the recessed groove of the
unit frame ensuring that
the pilot holes on panels
(G) line up with the drill
holes in the unit.
Once in place, secure with
12x screws (#11) as shown.
Please note that the 2x pilot
holes indicated at the top
corners of the unit are to
attach the anti-tip straps
included separately with this
item to secure the unit to the
wall. See Step 20.
STEP 12:
Prepare the large drawers by inserting 4x cam dowels (#7) to EACH of
the 2x large drawer fronts (I). Then attach 2x handles (#14) to EACH
of the large drawer front panels using 2x screws (#13) as shown using
your Philips screwdriver.
STEP 13:
Take 1x LH drawer side panel (J) and attach 1x runner (#4) with 3x
screws (#12) ensuring that you are positioning all screws through the
indicated holes.
Note: The runner will t the full length of the panel and should be positioned
with the wheel at the end next to the 2 small drill holes as shown. It should
NOT be on the side with the groove.
REPEAT with the remaining 3x panels (J).
STEP 14:
Take 1x RH drawer side panel (K) and attach 1x runner (#3) with 3x
screws (#12) ensuring that you are positioning all screws through the
indicated holes.
Note: The runner will t the full length of the panel and should be positioned
with the wheel at the end next to the 2 small drill holes as shown. It should
NOT be on the side with the groove.
REPEAT with the remaining 3x panels (K).
Hardware for Step 11:
Hardware for Step 12:
Hardware for Step 13:
Hardware for Step 14:
12x #11 Screws (16mm)
8x #7 Cam Dowels
4x #4 LH L-Shaped Runners
4x #3 RH L-Shaped Runners
4x #13 Flat-Ended Screws
(24mm)
12x #12 Screws (12mm)
12x #12 Screws (12mm)
4x #14 Handles
A
F
D
J
K
G
G
C
B
#11
#11
#11
#11
#11
#11
#7
#7
#7
#11
#11
#11 #11
#11
#11
#7
#13
#13 #12
#12
#12
#12
#12 #12
#12
#12
#3
#4
#12
#12
#12
#12
#14
#14
I
#4
#3