Great Little Trading Wall-Mounted Desk Storage & Pinboard L5249 User manual

1
Wall-Mounted Desk Storage & Pinboard
18/06/2021
V1
easy - medium- hard
Assembly Difculty
one-person job
A few important pointers before you start:
• Please read the instructions right through before you start, and
check that all the components have been included in the pack;
we nd separating all the hardware into piles makes it easier to
be sure that everything is present and correct.
• Make sure you have the right tools.Allen keys are provided
if required, but screw drivers and other tools are not.You’ll
nd details of the tools you need at the beginning of the
instructions.
• It’s a good idea to build the unit in the room where you are
going to be using it, to avoid the need to move it after it’s been
assembled.
• Do not throw away any packing materials until assembly is
complete, just in case you accidentally discard smaller parts or
hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.

2
Safety Warnings:
• WARNING! Not suitable for children under 3 years due to small parts
which may become detached and present a choking hazard.
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Wall xings not included. Please use appropriate xings that are
suitable for the wall type. If in doubt, please seek professional advice.
• Maximum weight load 20kg. Do not overload.
• Check all xtures and ttings regularly and tighten as necessary.
• Position the desk hutch so that your child can reach the storage
without needing to climb on other pieces of furniture such as the desk,
table or chair as this may lead to injury due to falls.
• PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
A B
C D
E F
G
1x Side Panel (shelf side) 1x Side Panel (pinboard side)
1x Base Panel
1x Central Divider Panel
1x Shelf Panel
#1 #2
#3 #4
#6
#7
#5
8x Cam Dowels 8x Wooden Dowels
4x Shelf Pegs
8x Cam Locks 14x Back Panel Screws
(14mm)
8x Keyhole Fixing Screws
(19mm)
You will need
(not supplied)
Philips Head Screwdriver
1x Top Panel
1x Back Panel (with pinboard)
Component Check List Hardware Check List
4x Keyhole Plate
(for wall mounting)
The building of the product is straight forward, however, the wall-
mounting of the unit may need additional help and support
You will need, but not supplied:
x4 Screws and Wall Plugs that are appropriate for the wall
construction where you are mounting.
Screws must have countersunk heads of 8-9 mm diameter and be able to
support a minimum of 25kgs of weight.
See installation guide at the end of the instructions and if you are
unsure, we recommend seeking professional advice.

4
STEP 2:
Note: You will be building with the back facing up.
Take side panel (A) and insert 1x wooden dowel (#2) into the hole
between the 2x cam dowels. Orientate the side panel with the grooved
edge facing up and connect with base panel (C) as shown. Ensure
panel (C) has the grooved edge facing up and the large drill holes facing
outwards.
Insert 2x cam locks (#3) into the large drill holes on panel C and turn
clockwise to secure.
Hardware for Step 1: Hardware for Step 2:
STEP 1:
Working on a protective surface like a rug or carpet, take both side panels
(A & B) and insert 2x cam dowels (#1) into EACH panel as shown.
A
BC
A
#1
#1
#1
#1
#1
#3
#3
#2
#3
1x #2 Wooden Dowel
4x #1 Cam Dowels
2x #3 Cam Locks
Using Cam Locks:
When inserting into the panel, ensure that
each cam lock’s arrow is pointing towards
the drill hole on the side edge of the panel
& the dowel that it will be receiving.
When the panels are in the connected
position, using a screwdriver, turn the cam
lock in a clockwise direction to lock and
secure.
Note: Ensure the grooved edges
are facing up.

5
STEP 3:
Take side panel (B) and insert 1x wooden dowel (#2) into the hole between
the 2x cam dowels. Orientate the side panel (B) with the grooved edge facing
up and connect with base panel (C) as shown.
Insert 2x cam locks (#3) into the large drill holes on panel C and turn
clockwise to secure. Hardware for Step 4:
4x #1 Cam Dowels
STEP 4:
Take top panel (D) and insert 4x cam dowels (#1) into the drill holes in
the 4 corners of the panel.
Hardware for Step 3:
1x #2 Wooden Dowel
2x #3 Cam Locks
D
#1
#1
#1
#1
#1
#3
#3
#3
#2
#2
C
A
B

6
STEP 5:
Take central divider panel (E) and with the grooved edge facing up, connect
with base panel (C) using 2x wooden dowels (#2).
Insert 4x wooden dowels (#2) in the remaining holes of top panel (D).
Now orientate top panel (D) so the grooved edge is facing up and connect
with the side panels (A & B) and the central divider panel (E).
Insert 2x cam locks (#3) into the large drill holes on BOTH side panels (A &
B) and turn clockwise to secure panel in place.
STEP 6:
Take back panel (F) and lay it onto the unit.
Orientate the panel so the pinboard is on the
LH side on the inside of the unit. Align the
drillholes on the panel with those on the unit.
Position the 4x keyhole plates (#6) in the
recesses on the back panel with the thinner
part of the keyhole cut out at the top and x
in place with 8x screws (#5).
Now nish attaching the back panel with 14x
screws (#4) using the remaining drill holes in
the panel.
6x #2 Wooden Dowels
Hardware for Step 5: Hardware for Step 6:
14x #4 Back Panel Screws
8x #5 Keyhole Fixing Screws
4x #6 Keyhole Plates
#3
#3
#3
#2
#2
#2
#2
#2
C
A
B
E
D
#3
#3
4x #3 Cam Locks
F
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#4
#5
#5
#5
#6
#5
#5 #5
#5 #5
#5
#5
Note: Attach with
the thinner part of
the keyhole cut out
at the top.

7
STEP 7:
Insert the 4x shelf pegs (#7) into the desired
position, then insert the shelf panel (G).
Your unit is now ready for wall mounting.
#7
#7
#7
#7
#7
4x #7 Shelf Pegs
Hardware for Step 7:
G
Wall Mounting Guidance
(2 people are needed for wall-mounting this product)
The hardware and wall plugs for wall-mounting the desk hutch are not
provided as the hardware used needs to be suitable for the walls in your
home. This desk hutch needs a strong and secure xing so please source the
appropriate hardware that is suitable for weight bearing of 25kgs (minimum)
and seek professional advice if you are unsure.
The hardware (x4) needs to have a countersunk screwhead of 8-9mm
diameter so it ts snugly into the keyhole xings used on the unit and be a
suitable length for weight bearing.
Check the screwhead is suitable before using it by inserting into the keyhole
xing plate, slide up into the narrow part of the keyhole xing plates and
check it doesn’t pull out.
Positioning: Please position the desk hutch above the desk top so that your
child can reach the storage without climbing on the desk, table or chair.
Check the wall for pipes and cables.
Ensure that you have a spirit level, pencil, tape measure, drill and drill bits to
hand.

8
2. Vertical measurement:
Measure from the TOP of the thin part of the upper key hole xing to the TOP
of the thin part of the lower keyhole xing. Measure both left & right xing
positions.
These measurements will be the vertical distance between the 2 sets of drill
holes. Repeat measurements to check they are correct.
1. Horizontal measurement:
Measure from the LH edge of the thin part of the keyhole xing on one
side of the unit to the LH edge of the thin part of the keyhole xing on the
other side of the unit. Measure both the upper and lower xing positions.
These measurements will be the horizontal distance between the 2 sets of
drill holes. Repeat measurements to check they are correct.
Reverse view, keyhole xing must be fully
engaged with wall xings before use.
Copyright© 2021 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
Wall Mounting Guidance
(2 people are needed for wall-mounting this product)
1. Horizontal measurement
1. Horizontal measurement
2. Vertical measurement 2. Vertical measurement
We have suggested you
measure from the LH edge of
the thin part of the keyhole
xing on one side of the unit
to the LH edge of the thin
part of the keyhole xing on
the other side of the unit.
As this gives you a xed point
to measure the horizontal
distance between the key
hole xings.
We have suggested you measure
from theTOP of the thin part of
the upper key hole xing to the
TOP of the thin part of the lower
keyhole xing.
As this gives you a xed point to
measure the horizontal distance
between the key hole xings.
Weight loading of the desk hutch is a maximum
of 20kgs.
Mark the positions of all four mounting points on the wall with a pencil using
the measurements above and a spirit level to ensure the product will be
straight.
Check measurements again before drilling the wall and inserting the
appropriate wall xings.
Ensure the screw head is xed so that the keyhole xing is at against the wall.
Ensure all four keyhole xings are engaged with the wall
xings before using the unit.