Great Little Trading L4174 User manual

1
Devon Market Stall
07/11/2016
V1
easy - medium - hard
Assembly Difculty
L4174
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools. Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the
tools you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.
two-person job

2
Safety Warnings:
• Please read these instructions carefully before assembly.
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Not suitable for children under 3 years due to small parts that may
become detached and present a choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury.
• Assemble and use on a at and level surface.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• Check item regularly for signs of damage which may make the product
unsafe.
• To avoid possible injury from tipping - DO NOT allow children to
climb on the product.
• Check all xtures and ttings regularly and tighten as necessary.
• Complies to the European Toy Safety Directive.
• DO NOT use this item if any components are missing or damaged.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you

3
Component Check List
#1
4x Castors 16x Short Screws
10mmL
30x Dowels
20mmL
20x Cam Locks
14mm dia
6x Barrel Nuts
10mmL
You will need
(not supplied)
Phillips Head
Screwdriver
6x Barrel Nut Bolts
42mmL
#2 #3 #4
#5 #6 #7
A
2x
#8
#9
20x Cam Dowels
35mmL
4x Long Screws
50mmL
1x Allen Key
1x
1x 1x
2x 1x
1x 1x
2x 2x
2x 1x
1x 1x
1x
B
C D
E F
H I
J K
L M
N O
G

4
STEP 1:
Attach 2x cam dowels (#2) to both panels A.
STEP 2:
Attach 2x castors (#1) to panel B using 8x short screws (#3).
Repeat this step for panel C.
A
#2
#2
#1
#1
#3
#1
#1
#3
Hardware for Step 1:
4x #2 cam dowels
Hardware for Step 2:
16x #3 10mmL screws
4x #1 castors
x8 x8
Hardware for Step 3:
2x #5 cam locks
2x #4 dowels
Hardware for Step 4:
2x #5 cam locks
2x #4 dowels
#5
#5
#4
#4
#5
#4
#5
#4B C
A
STEP 3:
Attach assembled panel B to panel A using 1x dowel
(#4) and 1x cam lock (#5). Turn cam lock clockwise to
lock. Repeat this step for panel C.
When attached correctly the holes on panel B and C
should face outwards.
STEP 4:
Attach the remaining panel A to panels B and C using
2x dowels (#4) and 2x cam locks (#5). Turn cam lock
clockwise to lock.
B
C
holes should face outwards
B
C
Turn cam locks 180
degrees or until tight.
Turn cam locks 180
degrees or until tight.

5
Hardware for Step 5:
12x #2 cam dowels
Hardware for Step 6:
#2
#2 #2
#2
#2 #2
#7
#7
#4
#4
#6
#6
2x #4 dowels
2x #6 barrel nuts
2x #7 barrel nut bolts
Hardware for Step 7:
6x #5 cam locks
2x #4 dowels
#5
#4
#4
#5
#5
#5
#5
#5
STEP 5:
Attach 6x cam dowels (#2) to panel D.
Repeat this step for panel I.
STEP 6:
Loosley attach pieces F and G to panel I using 2x dowels (#4) and 2x
barrel nuts and bolts. Now slot rod H between pieces F and G, with the
rod in place now fully tighten the barrel nuts and bolts.
STEP 7:
Attach base assembly to panel D using 2x dowels (#4)
and 6x cam locks (#5). Turn cam locks clockwise to
lock.
D
I
F
G
H
D
Turn cam locks 180
degrees or until tight.

6
Hardware for Step 8:
2x #4 dowels
Hardware for Step 9:
2x #4 dowels
#4
#4
#4
#4
STEP 8:
Using 2x dowels (#4) push panel E into panel D.
STEP 9:
Using 2x dowels (#4) push panel E into panel D.
EE
D
D

7
Hardware for Step 10:
10x #4 dowels
#4
STEP10:
Insert 2x dowels into both ends of both
panels J. Now push these into panel D.
Insert 2x dowels into the end of both shelf panels E.
Insert 2x dowels into panel B
The help of a second
person may make this
step easier.
STEP 11:
You are now ready to secure the base unit. Attach panel I to the assembly using 6x
cam locks (#5). Carefully lower panel I onto the assembly, making sure all dowels and
cam locks / dowels engage.Turn cam locks clockwise to lock.
Remember to secure all 6 cam locks, 2 of them will be partially hidden once
assembled.
The help of a second
person may make this
step easier.
Hardware for Step 11:
6x #5 cam locks
#4
#4
#4
#4 #4
#4
#4
#4
#4
J
J
D
E
E
#5
#5
#5
#5
#5
#5
I
B
Turn cam locks 180
degrees or until tight.

8
Hardware for Step 12:
4x #8 50mmL screws
4x #6 barrel nuts
4x #7 barrel nut bolts
#8
#8
#7
#8
#8
#7
#7
#7
#6
#6
#6
#6
Hardware for Step 13:
4x #2 cam dowels
#2
#2
#2
#2
STEP 12:
Firstly attach poles 2x M to left hand panel L using 2x screws (#8).
Now slide the canopy (O) over both poles (M).
With the canopy in place, now slot pole N into left hand panel L.
Now attach right hand panel L to poles M using 2x screws (#8), this action will also
secure pole N at the same time.
With the canopy now securely assembled. Place the assembly on its side and attach
both panels (L) to base (K) using 4x barrel nuts (#6) and bolts (#7).
STEP 13:
Attach 4x cam dowels (#2) to the base of panel K.
K
L
L
O
M
M
N
K

9
Copyright© 2017 G.L.T.C. Ltd. All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
Hardware for Step 14:
4x #5 cam locks
8x #4 dowels
#4
#5
#5
#5
#5
#4
#4 #4
#4 #4
STEP 14:
Attach the top assembly to the base assembly using
8x dowels (#4) and 4x cam locks (#5). Turn cam locks
clockwise to lock.
The assembly is now complete.
Turn cam locks 180
degrees or until tight.