Gree XK60 User manual

Change for life
Commercial Air Conditioners
Wired Controller
XK60
Owner's Manual
Thank you for choosing our commercial air conditioners. Please read this owner's manual
carefully before operation and retain it for future reference.
This owner's manual is subject to change without prior notice for product improvement.
GREE Electric Appliances, Inc. of Zhuhai reserves the nal right to interpret this manual.

User Notice
Please carefully read this manual before installation operation.
◆Thanks for choosing GREE duct type air conditioners. Please read this manual carefully
before operating this product and keep it for future reference. In addition, please observe
the following Notes:
WARNING! This mark indicates procedures which, if improperly performed, might lead to
the death or serious injury of the user.
CAUTION! This mark indicates procedures which, if improperly performed, might possibly
result in personal harm to the user, or damage to property.
CAUTION!
(1). Do not install the wired controller in the damp place or under direct sunlight.
(2). Do not drop, toss, or frequently assemble/disassemble the wired controller.
(3). Do not operate the wired controller with wet hands and keep dry at all times.
(4). Do not install or remove the wired controller by yourself. If necessary, please contact
a trained service technican.
(5). This wired controller is applicable to various kinds of air conditioners, while some specic functions
are unavailable to the duct type air conditioners will not be described in this manual.
(6). Before operating the air conditioner, please read this manual carefully and keep it for
future reference.

OVERVIEW OF WIRED CONTROLLER
XK60 Tether Wired Controller
Wired Controller Button Description
Button
Button Name
Function
1
Enter/Cancel
Function selection and cancellation.
2
▲
6
▼
Adjust room setpoint temperature (61 ~ 81°F / 16 ~ 30℃range).
Or adjust Timer & Sleep setting, (0.5-24 hr. range)
3
Fan
Set Fan Speed (High, Medium, Low & Auto)
4
Mode
Set Operating Mode (Cooling, Heating, Dry, Fan Only and Auto mode)
5
Function
Press to select Timer, Sleep Turbo & X-Fan, functions
7
Timer
Set Timer Mode.
8
On/Off
Turn on/off the unit.
1

OVERVIEW OF WIRED CONTROLLER
Wired Controller LCD Display
No.
Symbols
Description
1
Swing function
2
Sleep Mode function
3
Running modes (Heating Cooling, Dry, and Fan Only).
4
Defrosting function for the outdoor unit.
5
Not Available
Function not available
6
Keyboard Lock function.
7
Fan Speed (High, Medium, Low or Auto fan speed)
8
Not Available
Function not available
9
TURBO
Turbo Mode function.
10
MEMORY
Power Failure Recovery
11
Not Available
Function not available
12
Not Available
Function not available
13
Not Avail.
Function not available
14
188
Room Ambient/Setpoint temperature value.
15
Not Avail Function not available
16
X-Fan Mode function.
17
88.8
Timer Mode value.
2

OPERATION OF WIRED CONTROLLER
Operation Instructions
On/Off
Press On/Off to turn on the unit and press again to turn it off.
“OFF” State ON” State
Mode Setting
The system can be put in Auto, Cooling, Dry, Heating or Fan Only operating mode.
Select an operating mode, press the Mode button until the desiredoperating mode symbol
appearson the display.
Mode Sequence
Temperature Setting
In the Cooling, Dry, Fan Only or Heating mode, press ▲or ▼ to increase/decrease the room
setpoint temperature. The room temperature range is 61 ℉- 86 ℉(16℃- 30℃).
In the Auto mode, the unit will automatically selecting heat or cooling to maintain room setpoints.
The Heating setpoint is fixed at 82 ℉(28℃) and the Cooling and Dry setpoint is fixed at 77 ℉(25℃).
Neither can be adjusted.
Press ▲or ▼ to increase/decrease the room setpoint
3

OPERATION OF WIRED CONTROLLER
Setting Fan Speed
Press Fan button to change fan speed of the indoor unit. The fan speeds will change circularly as
shown above.
Setting Timer Mode
To set the Timer ON Mode, press Timer button and the LCD display will blink “xx.x hour”. Press the
▲or ▼ buttons to adjust the timing period between 0.5 to 24-hrs. Then press Enter to confirm the
settings. The system timer will start counting down and turn OFF or ON when time expires.
Turn ON unit Press TIMER button Select time period Press Enter to start Timer
To cancel Timer Mode, Press Timer Button.
Press Timer button Press Cancel to stop Timer
4

OPERATION OF WIRED CONTROLLER
Setting Swing Louver
To turn ON the Swing Louvers, press the Function button. The swing louver symbol will start
blinking. Press the Enter button to confirm.
To start - Turn ON unit Press FUNCTION button Press ENTER button to confirm
To turn OFF the Swing Louvers, press the Function button. The swing louver symbol will start
blinking. Press the Cancel button to confirm.
To cancel- Press FUNCTION button Press CANCEL button to Stop Swing Louver
5

OPERATION OF WIRED CONTROLLER
Setting Sleep Mode
The unit will automatically adjust room temperature during your sleep time. This slight
change in temperature will not affect your comfort level due to the natural effects that
sleeping has on the body, but it will save on energy consumption and will lower your electric
bill.
In Cool or Dry modes:
The unit will run at current room setpoint for 1 hour. After 1 hour, the setpoint will increase by
2° F.
After 2 hours, the setpoint will increase by 4° F and maintain this setpoint until Sleep Mode is
cancelled.
In Heat mode:
The unit will run at current room setpoint for 1 hour. After 1 hour, the setpoint will decrease
by 2° F. After 2 hours, the setpoint will decrease by 4° F and maintain this setpoint until
Sleep Mode is cancelled.
To start Sleep Mode,turn the system ON and press the Function button until the
Sleep icon appears on the display and the “xx.x hour” will start blinking. Press the ▲or ▼
buttons to adjust the timing period between 0.5 to 24-hrs. Then press Enter to confirm the
settings.
To start - Turn ON unit Press FUNCTION button Press the ▲or ▼ Press ENTER button to confirm
To cancel Sleep Mode, press the Function button until the Sleep icon starts blinking. Then,
press the Cancel button.
6

OPERATION OF WIRED CONTROLLER
Turbo Setting
The desired room setpoint, either in heating or cooling, can be achieved faster in TURBO mode. The
unit will run at ultra-high speed fan until room setpoint is satisfied.
In the Cooling or Heating mode, press Function button until the Turbo symbol will start blinking.
Press the Enter button to confirm.
To start - Turn ON unit Press FUNCTION button Press ENTER button to confirm
To cancel Turbo Mode, press the Function button until the Turbo icon starts blinking. Then,
press the Cancel button.
Press Timer button Press Cancel to stop Timer
7

OPERATION OF WIRED CONTROLLER
Setting X-Fan Mode
After turning OFF the system, the indoor fan will continue to run for 10 minutes at low speed
to evaporate excess moisture on indoor coil.
In the Cooling or Dry, press Function button until the X-Fan symbol BLOW will start blinking. Press
the Enter button to confirm.
To start - Turn ON unit Press FUNCTION button Press ENTER button to confirm
To cancel X-Fan Mode, press the Function button until the X-Fan icon BLOW starts blinking.
Then, press the Cancel button.
Press FUNCTION button Press Cancel to stop X-Fan
8

OPERATION OF WIRED CONTROLLER
Setup Modes
The system has three (3) special setup modes to customize the unit to the installation.
Keyboard Lock
The Locking Keypad prevents unauthorized access to the heating and
cooling controls.
To lock the keypad on the wired controller, the unit must be in the “Off”
state. Press ▲and ▼buttons at the same time for 5s. The Keypad
Lock icon will be display to signal the keypad is locked.
To unlock the keypad, press ▲and ▼buttons at the same time for 5s.
The Keypad Lock icon will disappear from the display to signal the
keypad is unlocked.
Failure Recovery Power Mode
The system can be configured to resumes the original settings
or be placed in Off Mode after power failure.
To activate the Power Failure Recovery Mode, the unit must be in the
“Off” State. Press Mode and ▲buttons at the same time for 5s. The
Power Failure Recovery display icon MEMORY will be display.
To deactivate Power Failure Recovery Mode, press Mode and ▲
buttons at the same time for 5s. The Power Failure Recovery display
icon MEMORY will disappear from the display.
The unit will power up in Off Mode as the default setting from the factory.
Fahrenheit or Celsius Display
The wired controller LCD display may display temperatures Fahrenheit
or Celsius.
To set the Fahrenheit or Celsius Temperature display, the unit must be
in the “Off” State. Press Mode and ▼Timer buttons at the same time
for 5s. The display will toggle between Celsius and Fahrenheit scales.
Press Enter to save.
9

OPERATION OF WIRED CONTROLLER
Temperature Display Mode
The wired controller LCD display may display either room temperature sensed at the system,
room temperature sensed at the wired controller, or return air temperature sensed at the
indoor unit.
To set the temperature display, the unit must be in the “Off” State. Press Function and Timer
buttons at the same time for 5s. The temperature display will show 00. Press the Mode button to
select the Display Code for the desired temperature display. Press Enter to save the section.
Press the Function & Timer Buttons Select with Mode Button Press Enter button to save.
Display
Code
Temperature Display Mode
01 Return air temperature sensed at the return air inlet.
02
Indoor ambient temperature sensed at the wired controller.
03 Return air temperature sensed at the return air inlet during Cooling, Dry and Fan modes.
And display the indoor ambient temperature sensed at the wired controller during Heating & Auto modes.
04
Indoor ambient temperature sensed at the wired controller during Cooling, Dry and Fan Only modes.
And return air temperature sensed at the return air inlet during Heating & Auto modes.
Factory default setting is Display Code 03.
CAT NO: GREE_X60_OWNERS_112918