Heat & Glo LOGS-6000GLX User manual

Heat & Glo • 6000GLX-IPI • 2101-910 Rev. C • 8/06 1
STEP 2.
Place the metal grate on top of the burner.
Position the legs of the grate into the forward set
of indentations in the burner top. See Figure 2.
STEP 1.
CAUTION: Logs are fragile! Carefully remove
the logs, grate and supporting cardboard from
the inside of the fireplace See Figure 1.
If the gas logs have been factory installed they
should not need to be positioned. If the logs have
been packaged separately, refer to the following
instructions.
Figure 2
Figure 4 Top View
1
1
2
2
3
3
4
4
5
5
STEP 3.
Log #1 NG (SRV2101-085):
Log #1 LP (SRV2101-087):
Log #1 is the left burning log. The air shutter in
theendofthe burnertube goesover theleft brass
orifice located behind the main burner. The left
endof the loggoes tightagainst theleftrefractory
wall. See Figures 3 and 4.
1
1
Figure 1
1
1
Figure 3 Front View
6
6
7
7
Log Set Assembly: LOGS-6000GLX
LOGS-6000GLXLP
Model: 6000GLX-IPI
LOG PLACEMENT
INSTRUCTIONS
HUMP
HUMP

Heat & Glo • 6000GLX-IPI • 2101-910 Rev. C • 8/06
2
Figure 6 Top View
STEP 4. Log #2 NG (SRV2101-086): Log #2 LP (SRV2101-088): Log #2 is the right burning log. The air
shutter in the end of the burner tube goes over the right brass orifice located behind the main burner. The right end of the
log goes tight against the right refractory wall.
STEP 5. Log #3 (SRV2101-197): Place log #3 on top of the burner surface in front of the hump. Slide it back against
the hump and the “V” notch in the bottom of the log rests into the second grate tine from the left.
STEP 6. Log #4 (SRV386-716): Place log #4 on top of the left side of log #2. The bottom of this log has a slot in it
that goes over the tab molded into the top of log #2. The other end of the log rests in the flat area on top of log #3
Figure 8 Top View
Figure 10 Top View
2
2
3
3
4
4
2
2
3
3
4
4
Figure 7 Front View
Figure 5 Front View
Figure 9 Front View

Heat & Glo • 6000GLX-IPI • 2101-910 Rev. C • 8/06 3
Figure 12 Top View
STEP 7. Log #5 (SRV2101-195): Place log #5 on top of log #1 and log #4. The bottom of this log has two slots in
it that both go over the two tabs molded in the top of log #1.
STEP 8. Log #6 (SRV2101-196): Place log #6 on top of log #2 and the grate. There is a slot in the bottom of this
log. Place the slot over the tab on top of the right end of log #2. The end of this log has a square notch in it that rests into
the second tine from the right on the grate. Note: May be necessary to tilt grate forward to interlock bottom notch in log.
STEP 9. Log #7 (SRV530-703): Place log #7 on top of log #1 and the grate. The lower right end of the log rests
against the second tine from the left on the grate.
Figure 14 Top View
Figure 15 Top View
5
5
6
6
7
7
5
5
6
6
7
7
Figure 13 Front View
Figure 14 Front View
Figure 11 Front View