Heat & Glo LOGS-I30FB User manual

1
Heat & Glo • LOGS-I30FB Log Instructions • 2201-935 Rev. G • 5/18
Log Set Assembly: LOGS-I30FB
Models: ESCAPE-I30-C, ESCAPE-I30FB, ESCAPE-I30-F, ESCAPE-30-IFT
LOG PLACEMENT INSTRUCTIONS
CAUTION: Logs are fragile, handle with care.
Figure 1. Log Set Installed
Figure 2. Reference Points
PILOT
BRACKET
GRATE TINES
BURNER LEDGE BURNER LEDGE
LIGHT TRAYS
SRV2201-702
SRV2201-704
SRV2201-703
SRV2201-701
SRV2201-705
SRV2201-706
LOG PINS
Log #1 (SRV2201-702): See Figure 2 for additional references. Position Log #1 as shown in Figure 3. Rest the left and
right ends of Log #1 on the burner ledge. The pilot bracket will support the center of the log.
Figure 3. Log #1
LOG RESTS ON
PILOT BRACKET
REST LOG ON
BURNER LEDGE
FLAT SPOT FOR LOG #5
1
5
12
4
3
GRATE BAR
1
2
34
56
6

Heat & Glo • LOGS-I30FB Log Instructions • 2201-935 Rev. G • 5/182
Log #3 (SRV2201-704): See Figure 2 for additional details. Locate the log slot on the bottom right end of Log #3. Mate the
log slot with the left log pin. Rotate the left end of the log counterclockwise, until it contacts the grate tine.
Log #4 (SRV2201-705): See Figure 2 for additional details. Locate the log slot on the bottom left end of log #4. Mate the
log slot with the right log pin. Rotate the right end of the log clockwise, until it contacts the grate tine.
Figure 5. Log #3 Figure 6. Log #4
34
Log #2 (SRV2201-701): See Figure 2 for additional references. Position Log #2 as shown in Figure 4. Mate Log #2 with
the right corner of the burner as shown. Pull the log forward and to the left until it locks into position.
LOG CONTACTS LEFT
GRATE TINE
LOG CONTACTS RIGHT
GRATE TINE
Figure 4. Log #2
LOG HANGS OVER
ONTO BURNER TOP
2
1
4
LOG CONTACTS RIGHT
GRATE TINE
FLAT SPOT FOR
LOG #6

3
Heat & Glo • LOGS-I30FB Log Instructions • 2201-935 Rev. G • 5/18
Figure 8. Place Log #5
Figure 9. Place Log #6
GLASS ROCK (2201-853): Once Log #3 and Log #4 are installed, ll each light tray with the glass rock. See Figure 7.
WARNING! Risk of Explosion! DO NOT place glass rock on the burner surface. DO NOT place glass rock directly over
burner ports. Improperly placed glass rock interferes with proper burner operation.
LOG #5 (SRV2201-703): SEE FIGURE 2 FOR ADDITIONAL REFERENCES. Place the thick end of Log #5 on the at
spot of Log #1. Locate the groove on the thin end of the log. Mate the groove with the grate bar as shown above. Swing
the front end of the log to the right, until it contacts the second grate tine from the right.
PLACE LOG ON FLAT SPOT
FLAT SPOT
FOR LOG #6
Log #6 (SRV2201-706): See Figures 2 and 4 for additional references. Place the thick end of the log on the at spot of Log
#2. Place the thin end of the Log #6 on the at spot of Log #5 as shown in Figure 8.
GROOVE MATES
WITH GRATE BAR
5
6
Figure 7. Glass Rock in Place
GLASS ROCK
LOG TOUCHES GRATE TINE