Herman Miller Layout Studio Installation instructions

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 1
YLayout Studio™Storage Installation and Disassembly for
Recycling Instruction
Parts Included:
Dual Sided Cubby Single Sided Cubby
Parallel Rail Mounted
Stanchion
Perpendicular Rail
Mounted Stanchion
Lower Plate Upper Plate
(L2SS.CE)
Upper Plate (2)
(L2SS.CS)
M6 Hex Nut (4)
M6 Hex Nut (4)
Clamp Assembly (2)
Flat Washer
5/16-18 x 3” Hex
Socket Head
Cap Screw
M6 x 35 Hex
Socket Head
Cap Screw (2)
AB
C
N
DEF
K
K
U
H
G
T
Hardware Pack
Hardware Pack
Lower Plate Upper Plate Spin Stanchion
PRS
L
L
M
V
M6 x 20 Socket
Flat Head Machine
Screw (2)
M6 x 20 Socket
Flat Head Machine
Screw (2)
10-13 x 3/4 Flat
Head Wood
Screw (4)
10-12x 5?8 Pan
Head Tapping
Screw (4)
T - Nut
J

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 2
H
G
C
J
M
E
A
1. Attach Upper Plate (E) (shown) or shared
stanchion Upper Plate (F) to Cubby (A)
with fl athead screws (M).
2. Assemble T-Nut (J) to Parallel Rail
Mounted Stanchion (C) with hex socket
head cap screw (G) and fl at washer (H).
Make sure “T” on T-Nut faces up.
3. Set stanchion assembly onto
performance rail.
Tools Required:
#4 Allen Wrench #5 Allen Wrench M6 wrench Level
Cubbly Insert Adhesive Spacer
WX
L2SS.CE & L2SS.CS
Performance Rail
“T”
#2 Phillips Bit
Power Driver

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 3
D
6. Align top edge of cubby with edge of work surface.
7. Slide stanchion assembly along rail until upper and lower plates align.
LFE
4. Attach Lower Plates (D) to stanchions with 2 fl at head machine screws (L).
5. Set cubby onto work surface.

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 4
11. Place cubby into position on stanchions.
12. Secure in place with hex nuts (K).
8. Secure stanchion to rail.
9. Align other stanchion assembly to upper plate.
10. Secure to rail.
K

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 5
L2SS.PRC
3. Loosely assemble 2 Clamp Assemblies (U) to Perpendicular Rail Mount
Stanchion (N) with 2 socket head cap screws (T).
4. Assemble Lower Plate (P) to stanchion with 2 fl at head machine screws (L).
1. Attach Spin Stanchion (S) to bottom of Single Sided Cubby (B) with 4 pan
head tapping screws (V).
2. Position Upper Plate (R) onto cubby. Note where pilot holes line up with
holes in plate.
3. Attach plate to cubby with 4 pan head tapping screws (V).
T
S
N
V
R
U
B
PL

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 6
5. Insert stanchion assembly into gap between rail and work surface.
6. Once stancion is in it’s proper location, tighten down clamps.
7. Place cubby onto stanchion.
8. Secure cubby to stanchion with hex nuts (K).
K

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 7
9. Level cubby by turning spin stanchion to obtain proper height.
1. Remove protective backing on one side of Adhesive Spacer (X).
2. Press spacers onto Cubby Insert (W).
3. Remove protective backing from double sided tape on insert.
LLCM.Z
WX
Double Sided
Tape

Z
© 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Part no. 1BHB0T rev B.
TM Y, L, Canvas are among the trademarks of Herman Miller, Inc.
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue products. 8
Disassembly for Recycling:
Materials Identifi cation and Segregation:
Where possible, plastic components are marked with ASTM recycling codes.
Use these codes to identify material type for recycling. Non marked components
should be treated as mixed plastic. Ferrous metals can be identifi ed using a
small magnet for recycling. Non-ferrous metals should be separated and recycled
separately.
To disassemble product, reverse the above installation steps.
4. Remove remaining protective backing from adhesive spacer.
5. Slide Cubby Insert into cubby. Hold right edge of insert tight against right end
panel. Firmly press insert onto cubby.
End Panel