HOMCOM A90-193 User manual

ASSEMBLY INSTRUCTION
INada080V01_UK
A90-193
READ AND SAVE THIS INSTRUCTION FOR FUTURE USE

Please read the User Manual carefully before using this product and retain for
future reference.
Important Safety Instructions
Please read carefully prior to using this product.
You should consult a physician before beginning any exercise program including a
program involving the use of the spin bike – this is especially important if you
are pregnant, sick, injured or have a pre-existing medical condition. Your doctor's
advice is essential if you are taking medication that affects your heart rate, blood
pressure or cholesterol level. If whilst using the spin bike you feel dizzy, faint, short of
breath, or any pain, STOP using the bike immediately and consult a physician.
When using fitness equipment, you should follow normal safety
procedures, especially if there are children or pets around.
1. Always place the bike flat on the ground in a dry clean area, to avoid placing the bike
on thick carpet. For safety, the equipment should have at least 0.5 meter of free
space all around it.
2. Adjust the front and back stabilizers each time you use the bike to ensure it’s
stable and level with the floor.
3. In the event the bike malfunctions, PUSH down on the red EMMERGENCY STOP –
the bike will stop immediately – contact the distributor for further instructions.
4. Never exceed the MAX or STOP mark when adjusting the handlebars and saddle,
to ensure the adjustment locks are tight and secure.
5. Spinning pedals can cause injury and damage the bike – to reduce pedal speed,
add resistance by turning the TENSION control.
6. Regular maintenance will prolong the life of your bike and prevent injury – refer
to the Maintenance section below.
7. Always use proper lifting techniques and / or assistance when lifting or moving
the bike to avoid injury.
8. Never leave the bike unattended especially if there are young children around.
9. The Spin bike is not suitable for children under 14 years of age or for people with
physical conditions unless supervised by an adult.
10. The maximum user weight for the bike is 120KG.
11. The Spin bike is designed for home use only and should only be used indoors in a
clean dry area.

EXPLODED VIEW

NO. DESCRIPTION No. DESCRIPTION
1 main frame 14 handlebar supporting tube
2 M8 nut 15 Handle bar
3 Flat gasket 16 Combination screw
4 front stabilizer 17 Phone holder under part
5 M5x45 carriage screws 18 Phone holder upper part
6 Pedal L/R 19 Cross Tapping screw
7 rear stabilizer 20 Monitor holder
8 seat supporting tube 21 Monitor
9 seat sliding set 22 Tapping screw
10 Seat 23 6mm Allen wrench
11 gasket 24 Multi-function screwdriver.
12 M10 knob 25 Wrench
13 M16 knob
PART LIST

STEP 1 and 2
1. Fix the front stabilizer (4) and the rear stabilizer (7) to the main frame (1).
2. Lock into the proper place with the bolts (05), washers (03) and nuts (02) provided
– see the illustrations.
3. Firmly fix the pedal marked L (4) to the crank arm marked L (16) in an
anti-clockwise direction until tight. fix the pedal marked R (4) to the crank arm
marked R (16) in a clockwise direction until tight – see the illustration.
ASSEMBLY INSTRUCTIONS

STEP 3 and 4 and 5
1. Fix the seat supporting tube (8) into the main frame (1), to tighten it with the
adjustable knob (13), then slide the seat sliding set (9) into the seat supporting
tube (8), to lock in with the adjustable knob (12).
2. Now fix the seat (5) into the seat sliding set (9), to screw the nut of the seat until
tight.

STEP 6 and 7
1. Fix the handlebar (15) to the handlebar supporting tube (14) with the provided
bolts and washers. then install the phone holder under part(19) to the handle
supporting tube(14) and lock the tube with the adjustable knob (13). Finally ,
tighten the screws of the upper and under parts of the phone holder.
2. Lock the monitor (20) into the handlebar (14), then insert the monitor holder
(20) into the flute on the back of the monitor(21) – see the illustration. Then
remember to load the button battery, and connect the computer wire to the
monitor – see the illustration.
STEP 8
1. Lock the monitor (20) into the handlebar (14), then insert the monitor holder (20)
into the flute on the back of the monitor(21) – see the illustration. Then remember
to load the button battery, and connect the computer wire to the monitor – see the
illustration.

Most Important
After all above steps finished, the most important is to make sure all the bolts and
parts are securely fixed before you are riding on the bike.
COMPUTER OPERATING INSTRUCTIONS
SCAN Scans all functions – TIME, SPEED, DISTANCE, TOTAL DIST, PULSE, CALORIES
TIME Displays work out time lapse while exercising
SPEED Displays the current speed
DISTANCE Displays the distance while exercising
RMP Show the number of rotations per minute
PULSE Displays your heart rate
CALORIES Displays the calories you have burned

1. You will need one button battery (provided) to operate the Computer.
2. To select the function you want, press the MODE button and then select the
function of choice from the table above.
3. To reset the Computer, hold down the MODE button for 4 seconds.
4. The Computer will automatically turn off after 4 minutes when the bike is not in
use. Press any key to restart.
5. To monitor your heart rate, place your thumbs on the heart rate sensor for a few
seconds and check the display.
6. To adjust the resistance, turn the tension control to the right (harder), or to the
left (easier) .
7. If there is an improper display on the Computer, please replace both batteries
with new ones at the same time.
8. To move the bike, hold onto the saddle support pole, lift and push forward.