Honeywell Home Lynx 5210 User manual

6. If an alarm has been triggered:
a. Before proceeding, verify that the alarm was triggered accidentally. If you aren’t
sure, wait for the phone call from central station.
1. To set your alarm when leaving home:
a. Close doors and windows until a green ready light appears on the
security system panel.
b. Press the icon that says ARM AWAY and enter your four digit user code.
c. The keypad will begin to beep. Exit the home, close the door, and lock
it behind you.
2. To disarm the system when you return home:
a. Press the icon that says DISARM and enter your four digit user code.
3. To set the alarm with a delay when at home:
a. Close doors and windows until a green ready light appears on the
security system panel.
b. Press the icon that says STAY, and then enter your four digit user code.
4. In the morning, or before opening any protected door or window:
a. Press the icon that says DISARM, and then enter your four digit user
code.
5. To set the alarm when at home with no delay (night mode):
a. Press the icon that says DELAY. The security system panel should then
read INSTANT.
b. Press the STAY icon and enter your four digit user code.
Continued on Back
Lynx 5210
quick reference guide

The manufacturer of your security system recommends that you test it weekly to insure
that the system is communicating fully with the Monitoring Station in the event that an
alarm is triggered. If for any reason you feel your security system is not functioning
properly, do not hesitate to call our office at 770-963-0305. We have technicians available
to assist you twenty-four hours per day.
Lynx Touch 5210
quick reference guide
1. To set your alarm when leaving home:
a. Close doors and windows until a green ready light appears on the security system
panel.
b. Press the icon that says ARM AWAY and enter your four digit user code.
c. The keypad will begin to beep. Exit the home, close the door, and lock it behind
you.
2. To disarm the system when you return home:
a. Press the icon that says DISARM and enter your four digit user code.
3. To set the alarm with a delay when at home:
a. Close doors and windows until a green ready light appears on the security system
panel.
b. Press the icon that says STAY, and then enter your four digit user code.
4. In the morning, or before opening any protected door or window:
a. Press the icon that says DISARM, and then enter your four digit user code.
5. To set the alarm when at home with no delay (night mode):
a. Press the icon that says DELAY. The security system panel should then read
INSTANT.
b. Press the STAY icon and enter your four digit user code.
5. If an alarm has been triggered:
a. Before proceeding, verify that the alarm was triggered accidentally. If
you aren’t sure, wait for the phone call from central station.
b. Press the icon that says DISARM and enter your four digit user code.
This will silence the alarm.
6. Press the icon that says DISARM and enter your four digit user code again.
This will reset the alarm so that it can be set activated again later.
a. The Monitoring Station will call you and ask for your password to cancel
dispatch of local authorities. If you do not receive a call from the
Monitoring Station within sixty seconds, call 1-888-745-4733 immediately
with your password to cancel dispatch of local authorities.
b. To turn the door chime on or off:
c. Press the icon that says MORE.
d. Press the icon that says SETTINGS.
7. Press the icon that says CHIME. The green light will be on if the chime has
been activated or off if it has been deactivated.
a. To change your four digit master code:
b. Tap on the MORE icon.
c. Press the TOOLS icon and enter your current four digit master code.
8. Tap on the USERS icon, then MASTER and EDIT.
a. Under NAME is an icon that will display the code.
b. Enter your new four digit master code and press DONE and SAVE.
c. Tap the HOME button. Your four digit master code has been changed.