Honeywell MaxLED 26m User manual

GB
MaxLED
Dimensional Drawings:
330mm
230mm
336mm
460mm
427mm
700mm
198mm
52mm
304mm
52mm
395mm
52mm
MaxLED 26m MaxLED 47m MaxLED 65m
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
Installation:
Step 1: To dismantle the luminaire, push the lock/unlock button, slide the luminaire to the left
and pull it down.
Step 2: To gain access to the module address SET-10, lift the inner plastic cover (on top of the
luminaire).
Step 4: To insert pictograms, first unscrew the two screws holding the side profile and remove
the profile.
Step 5: For double sided pictogram, insert the appropriate pictograms to both sides and refit
the profile. For single sided pictogram, there is one blind pictogram in the package.
Step 3: Set the module address. For more information about module settings see the next
page.
1 2 3
5
4

GB
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
The product contains bracket for wall mounting and spacers for ceiling mounting.
Step 3: Tighten the cable tie around the cables.
Step 4: Slide the luminaire into the socket. The lock/unlock button appears
indicating that the luminaire is securely installed.
Step 2: Pass the mains cables through the cable gland. Always use in any
case round mains cable, with a diameter of 5-10mm (H05RN-F
type 2x1mm² or any other type, at least equal to it's mechanical and
electrical properties). ATTENTION!! The cable must not be
deformed in any way (This requirement is important to ensure the
IP rating). Connect the mains to terminal blocks: L for live wire, N for
neutral and PE for ground.
Step 1: Fasten the mounting part (with screws from within) to either wall bracket (supplied), ceiling (with or without
supplied spacers). If mounted close to a wall make sure, that the
unlock button is facing outwards.
Mouting Methods:
PRESS HERE
TO UNLOCK
PRESS HERE
TO UNLOCK
Power
cable Power
cable
Metal Wall Bracket
Spacers
Wall Mounting
Ceiling Mounting
At the end of their useful life the packaging and product should
be disposed of via a suitable recycling centre. Do not dispose of
with your normal household waste. Do not burn.
Technical description
Part no.:
o
-10 to 60 C
Up to 95%
Produced in accordance with:
Ambient Temperature Range:
Maximum Power Consumption:
Operation Voltage:
Relative Humidity:
Technical lifetime (light source):
Lumen output
> 100000 hours
280lm 550lm 850lm
MaxLED 26m MaxLED 65mMaxLED 47m
3.1W / 3.8VA 5.4W / 5.9VA 7.7W / 8.2VA
220-240V AC/DC, 50-60 Hz
290253.S10 290255.S10290254.S10
IP40
Degress of cover protection:
EN 60598-1, EN 60598-2-22, EN 55015
EN 61547, EN 61000-3-2, EN 61000-3-3
Weight: 800 gr 1190 gr 1765 gr
The light source contained in this luminary shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.

GB
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
MODULE FOR SINGLE LAMP SELECTION AND MONITORING
Switching of one selected light in the electric circuit
SET010 select
DIP-switch 1
ON for non-maintained mode
OFF for maintained mode (Default)
DIP-switch 2
OFF for lighting address 1-16 (Default)
ON for lighting address 17-32
Indicator LED
Rotary coding switch
for setting the exact lamp adress DIP-switch 3 (OFF)
Attention!
Connect L and N correctly!
Exchanging L and N causes malfunction.
Function
Setting the lighting address is carried out by a rotary coding switch that is easily accessible from the
outside.
By means of a suitable control, it is possible with the aid of the SET010 select to determine whether the
lamp connected to it is ready for use or faulty.
In the mixed operation circuit, the connected lamp can also be additionally set in non-maintained mode
or maintained mode (DIP Switch 1).
The address range 17 to 32 can be selected by setting DIP switch 2 to ON.
The module is already prepared for administering a total of 32 lighting addresses.
Settings
Lighting addresses 1 to 16 can be slected when DIP switch 2 is set at OFF.
(DIP switch 2 = ON and rotary coding switch = 1 is equivalent to lighting address 17 etc.)
Technical description
Cross section:
Temperature:
Dimensions (L x W x H in mm) 78 x 30 x 20
2
Max: 1.5mm
-10°C up to +60°C, T =+75°C
cmax
SET010 select
Prewired