HunterDouglas Design Studio PowerView Contempo Parts list manual

Design Studio™
PowerView
®
Motorization
Drapery Hardware
Contempo & Essential
Installation • Operation • Care

CONTENTS
Questions?
Call the Hunter Douglas Consumer Support Center at 1-888-501-8364.
© 2019 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.
GETTING STARTED
Product View—Contempo Motorized Drapery Hardware ..........................1
Product View—Essential Motorized Drapery Hardware ............................2
Tools and Fasteners Needed .......................................................................3
INSTALLATION
Wall Mount — Contempo...........................................................................4
Wall Mount — Essential.............................................................................6
Ceiling and Flush Ceiling Mounts — Contempo.........................................7
Flush Ceiling Mount — Essential................................................................9
Install the Track..........................................................................................10
Install the Drapery .....................................................................................12
Setting Close and Open Limits ..................................................................15
Using the PowerView®Remote ................................................................16
OPERATION
Operate the Track.......................................................................................17
Basic Operation..........................................................................................17
Reset End Limits (If Necessary).................................................................18
Troubleshooting ........................................................................................19
CARE
Remove Drapery (If Necessary) .................................................................20
Remove Drapery Track (If Necessary)........................................................20
Cleaning Procedures .................................................................................21
WARRANTY.................................................................................Back Cover

1
GETTING STARTED
Product View—Contempo Motorized Drapery Hardware
Wall Mount
Bracket
Drapery
Track
Lead
Carrier
Pleated
Carriers
PowerView®
Transceiver
Motor
Power
Supply
Data
Cable

2
GETTING STARTED
Product View—Essential Motorized Drapery Hardware
Wall Mount
Bracket
Drapery
Track
Lead
Carrier
PowerView®
Transceiver
Motor
Power
Supply
Data
Cable
Pleated
Carriers

3
GETTING STARTED
Thank you for purchasing Hunter Douglas Design Studio™PowerView®Motorized Drapery
Hardware. With proper installation, operation and care, your new drapery will provide years of
beauty and performance.
Please thoroughly review this instruction booklet and enclosed packing list before beginning
the installation.
Tools and Fasteners Needed
■ Phillips screwdriver
■ Level (laser level is recommended)
■ Measuring tape and pencil
■ Power drill,
1
∕ 8 " drill bit, and a Phillips driver
In addition, you will need fasteners designed to work with your specific mounting surface(s).
■ Contempo Wall Mount Brackets. Three 1
1
∕ 2 ” Phillips flat head screws are provided per
wall mount bracket.
■ Contempo Flush Ceiling and Ceiling Mount Brackets. One Phillips flat head screw is
provided per ceiling mount bracket.
■ Essential Flush Ceiling and Wall Mount Brackets. Three #8 1
3
∕ 4 ” Phillips pan head
screws.
Refer to the appropriate page below based on your order:
➤ “Wall Mount — Contempo” on page 4.
➤ “Wall Mount — Essential” on page 6.
➤ “Ceiling and Flush Ceiling Mounts — Contempo” on page 7.
➤ “Flush Ceiling Mount — Essential” on page 9.

4
INSTALLATION
Wall Mount — Contempo
■ Measure the width of the drapery track and use this measurement to determine where the
ends of the track will be located. Use a pencil to lightly mark where its ends are located.
■ Use the figure below to mark the locations on the wall for each of the brackets. Keep in
mind the following:
➤ A minimum of 1
7
⁄ 8 " flat vertical surface is required to mount the installation brackets.
➤ Measure the drapery ordered height plus 2
3
⁄ 4 " from the floor to mark the top hole
position of the brackets.
➤ Mount the end installation brackets 7" in from end marks.
➤ If more than two installation brackets came with your order, space additional bracket(s)
evenly between the two end brackets and mark their location. Mount into wood
whenever possible.
IMPORTANT: The installation brackets must be level and aligned after mounting.
■ Place the top hole of each back plate on the previously made marks and mark the two side
screw holes.
■ Drill the screw holes using a
1
∕ 8 " drill bit.
■ Attach the back plates using the screws provided.
➤ Check that the mounting surface is level and the back
plates are aligned. If mounting to a heavily textured
surface, shim the back plates, if needed.
WARNING: Product is heavy. Mount into wood/metal studs or into concrete
with concrete anchors. Drywall anchors can be used when studs are not present.
Choose the appropriate anchors to safely secure the track.
7"
End of Track Marks
Evenly Spaced Evenly Spaced Evenly Spaced
7"

5
INSTALLATION
■ Place decorative face plate over the back plate.
■ Thread the installation bracket on the back plate until it is tight.
■ Make sure the end of the installation bracket is oriented as shown. If not, change the
orientation:
➤ Loosen the bracket set screw then rotate the installation bracket. Once the installation
brack is oriented correctly, tighten the set screw.
Proceed to “Install theTrack” on page 10.
Bracket
Set Screw
Orient
Facing
Down

6
INSTALLATION
Wall Mount — Essential
■ Measure the width of the drapery track and use this measurement to determine where the
ends of the track will be located. Use a pencil to lightly mark where its ends are located.
■ Use the figure below to mark the locations on the wall for each of the brackets. Keep in
mind the following:
➤ A minimum of 1
1
⁄ 2 " flat vertical surface is required to mount the installation brackets.
➤ Measure the drapery ordered height from the floor to mark the top outside
hole position.
➤ Mount the end installation brackets 4" in from end marks.
➤ If more than two installation brackets came with your order, space additional bracket(s)
evenly between the two end brackets and mark their location. Mount into wood
whenever possible.
IMPORTANT: The front edges of the installation brackets must be level and aligned
after mounting.
■ Place the outside top hole of each wall bracket on previously made marks and mark the
top two and bottom hole.
■ Drill the screw holes using a
1
∕ 8 ” drill bit.
■ Attach the installation brackets using the three screws
provided.
➤ Check that the mounting surface is level and the brackets
are aligned. If mounting to a heavily textured surface, shim
the brackets, if needed.
WARNING: Product is heavy. Mount into wood/metal studs or into concrete
with concrete anchors. Drywall anchors can be used when studs are not present.
Choose the appropriate anchors to safely secure the track.
Proceed to “Install theTrack” on page 10.
4"
End of Track Marks
Evenly Spaced Evenly Spaced Evenly Spaced
4"

7
INSTALLATION
Ceiling and Flush Ceiling Mounts — Contempo
The following steps apply to both brackets.
■ Measure the width of the drapery track and use this measurement to determine where the
ends of the track will be located. Use a pencil to lightly mark where its ends are located.
■ Use the figure below to mark the locations on the ceiling for each of the brackets. These
marks will be the screw hole position of the ceiling bracket. Keep in mind the following:
➤ The marks need to be exactly 4
1
∕ 2 " away from the wall for the ceiling mount brackets
and 3
1
∕ 2 ” away for the flush ceiling mount brackets.
➤ Mount the end installation brackets 7" in from end marks.
➤ If more than two installation brackets came with your order, space additional bracket(s)
evenly between the two end brackets and mark their location. Mount into wood
whenever possible.
IMPORTANT: The front edges of the installation brackets must be level and aligned
after mounting.
7"
End of Track Marks
Evenly Spaced Evenly Spaced Evenly Spaced
7"

8
INSTALLATION
■ Loosen the brackets/stems to adjust.
➤ For standard brackets, loosen the bracket stems by turning it counterclockwise.
➤ For flush mount brackets, loosen the securing screws with the Allen wrench provided.
■ Measure and slide the stems/brackets along the drapery track to position each of them
the same distance as the previously made marks on the ceiling.
■ Drill the screw holes using a
1
∕ 8 " drill bit.
■ Attach the installation brackets using the screws provided.
➤ For flush mount bracket, hold the track up and align the brackets with the previously
made marks.
➤ Check that the mounting surface is level and the brackets are aligned.
WARNING: Product is heavy. Mount into wood/metal studs or into concrete
with concrete anchors. Drywall anchors can be used when studs are not present.
Choose the appropriate anchors to safely secure the track.
For Flush Ceiling Mount Brackets proceed to “Install the Motor and
Transceiver” on page 11.
For Ceiling Mount Brackets proceed to “Install theTrack” on page 10.
Marked Placement
Ceiling Mount Brackets
Ceiling
Installation
Bracket
Hex Screw
Flush Ceiling
Mount Brackets
Securing
Screw
Bracket
Track