IHP RIVROCK-25PK User manual

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
RIVROCK-25PK
TOOLS REQUIRED
1 Pair of gloves for handling media.
GENERAL INFORMATION
The River Rock Media is to be used as a decorative addition
to the fireplace models listed on this instruction sheet. Please
read this instruction sheet in its entirety before applying this
Contemporary Media.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY
TO THESE INSTRUCTIONS.
TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY
COOL BEFORE PROCEEDING.
CAUTION: TURN OF GAS TO THE APPLIANCE AND LOCK OUT
ANY ELECTRICAL SWITCHES.
INSTALLATION INSTRUCTIONS FOR RIVROCK-25PK KIT MEDIA
FOR USE IN ASTRIA ALLUMEDLX60TEN, ALLUME60TEN AND SUPERIOR DRL4060TEN FIREPLACES
HEARTH PRODUCTS
KITS AND ACCESSORIES
900933-00 REV. NC 10/2018
Table Of River Rock Media
Catalog
Number
Model
Number
Contemporary Media Name
F3775 RIVROCK-25PK River Rock - 25 Piece Kit
WARNING
Only use materials listed here. Only contemporary
media authorized have been tested for use within
the firebox and its environment. Do not attempt to
use any different materials in the fireplace. Doing
so may be dangerous and will void the warranty
and will result in incomplete combustion, sooting,
and poor flame quality.
WARNING
If media are not installed according to the installa-
tion instructions, flame impingement and improper
combustion could occur and result in soot and/or
excessive production of carbon monoxide (CO), a
colorless, odorless, toxic gas.
WARNING
Handle glass door with extreme care! Glass door is
susceptible to damage – do not scratch or handle
roughly while removing or installing the glass door.
PREPARING THE FIREPLACE FOR RIVER ROCK MEDIA INSTAL-
LATION
1. To access the glass door securing latches, first remove trim
kit (if installed) and screen barrier from fireplace.
2. Lift the barrier to clear the bottom channel and swing the
bottom of the barrier out. Then lower the barrier to clear the
top channel.
3. Detach the four (4) door latches on top of firebox.
4. Swing the top of the glass door away from the fireplace at
about 15° angle.
5. Carefully grip the door at the top and bottom, and remove it
from the fireplace. Place the door in a safe location for later
re-installation.
fire-parts.com

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
IHP.us.com
Innovative Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2018 Innovative Hearth Products LLC
P/N 900933-00 Rev. NC 11/2018 1769 East Lawrence Street • Russellville, AL 35654
Figure 1 - Glass Media and River Rocks placement
Figure 2 - Glass Media, River Rocks and Driftwood Logs
INSTALLING THE MEDIA
Install the River Rocks
IMPORTANT: Reflective glass liner panels (if applicable) should
be installed before any of the media are installed.
Note: Glass media is required. River rocks cannot be installed
without glass media installed.
Note: Maximum of 4 kits of river rocks when using river rocks
alone with glass media.
Note: Maximum of 2 kits of river rocks when using river rocks
combined with driftwood logs and glass media.
NOTE: The area for installing the river rocks measures 57” x
9-1/2”; burner area is located along the center of this dimension.
1. Spread the glass media in a thin layer, evenly over the burner
and pan media. Make sure not to place any media over the
pilot shield cover.
NOTE: Do NOT mound the media.
2. Place river rocks over the glass media, in any aesthetically
pleasing manner to suit individual taste. See Figures 1 and
2 for an example.
IMPORTANT: Be sure river rocks do not impinge on the burner
outlet.
Re-Installing Glass Door, Access Door Cover and Barrier
1. Retrieve the glass door. Visually inspect the gasket on the
backside of the frame. Gasket surface must be clean, free of
irregularities and seated firmly.
2. Position the door in front of the firebox opening with the top
of the door held away from the fireplace at 15° angle. Hook
the bottom flange of the door frame over the bottom of the
firebox frame.
NOTE: Ensure the glass door is centered—with even spacing
on each side.
3. Let the top of the glass door swing gently in towards the
fireplace ensuring that the gasket seats evenly as the door
draws shut. Securely fasten the four (4) latches on firebox
top to secure door in place.
4. Install the access door into rectangular opening in front of
the glass door with the slanted side facing forward. Insert
tabs on sides of access door into slots on retaining brackets.
5. Install the barrier by sliding in into the top channel with the
flat side toward the fireplace, then swinging the base of the
barrier into the bottom channel and lowering it into place.
fire-parts.com