IHP Superior 900347-00 User manual

P/N 900347-00
Rev. NC 12/2014
HEARTH PRODUCTS
SUPPLEMENTAL INSTRUCTIONS
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
GLASS DOOR ASSEMBLY REMOVAL
DRT/DRC6300 SERIES GAS FIREPLACES
Figure 1
(2) Latch
Screws Glass Door
Assembly
Firebox Floor
(2) Door
Latches
~
~
Top Flange
CAUTION
RISK OF PERSONAL INJURY
OR PROPERTY DAMAGE.
• Do NOT abuse glass doors by striking or slamming shut
• Never operate fireplace with glass door assemblies removed.
These direct-vent appliances are designed to operate only when glass
door assemblies are installed. Generally, the glass door assemblies
should not be removed, except when access to components within
the firebox is required.
• Securely tighten door latch screws when reinstalling glass door
assemblies to prevent doors from falling out.
• Handle glass door assemblies with extreme care. Replace dam-
aged glass door assemblies with approved replacement assem-
blies only.
The door assemblies on this fireplace contain ceramic glass. Handle
with care to prevent damage. If the door frame or glass on either
assembly becomes damaged, replace the entire glass door assembly
with a manufacturer-approved replacement assembly only. Do not
attempt to substitute any materials used on door assemblies or
replace cracked or broken glass with any other materials.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
• Install only when fireplace is OFF and COLD.
• Fireplace surfaces get EXTREMELY HOT!
• The glass on the front of the fireplace reaches EXTREMELY HIGH
temperatures and can cause severe burns if touched. Even after
the gas is turned off, fireplace surfaces remain extremely hot.
• Keep children away from an operating fireplace. Closely supervise
children in any room where a fireplace is operating to prevent
contact with glass.
REQUIRED TOOLS
• #3 Phillips screwdriver
REMOVING GLASS DOOR, BARRIER,
AND MODESTY PANEL
1) Remove the barrier, as follows:
a) Lift barrier up by the frame at the top.
b) Remove lower filler piece by pulling down off of the barrier.
c) Lower barrier and push barrier to left to release right side.
d) Pull the right side out of fireplace.
e) Remove barrier.
2) Remove the modesty panel from the top flange of the glass door by
firmly pulling up on it with both hands until it is disengaged.
3) Remove glass door, as follows:
a) See Figure 1. While holding the top of the glass door frame in
place, use a #3 Phillips screwdriver to remove the two (2) screws
securing the door frame to the two (2) door latches.
b) Carefully tilt the top of the glass door frame away from the unit (as
shown in Figure 1), and then lift the door assembly up and out of
the lower track.
c) Carefully place the glass door assembly on a padded surface in a
safe location to prevent damage.
Note: These instructions do NOT apply to the outer glass door
provided in the Outdoor Kit for indoor/outdoor installations of
Montebello See-Through models.
REMOVAL (AND REINSTALLATION) INSTRUCTIONS FOR GLASS DOOR ASSEMBLIES
USED ON DRT/DRC6300 SERIES DIRECT-VENT GAS FIREPLACES*
P900347-00
*Superior Models: DRT6345TEN, DRT6345TEP, DRT6345TYN,
DRC6345TEN, DRC6345TEP, DRC6345TYN, DRT6340TEN,
DRT6340TEP, DRT6340TYN, DRC6340TEN, DRC6340TEP, and
DRC6340TYN
See other side for installation instructions.
fire-parts.com

INSTALLING GLASS DOOR, BARRIER,
AND MODESTY PANEL
See WARNINGS and CAUTIONS on other side.
NOTICE: Only doors certified with the appliance shall be used.
AVIS : Seules des portes certifiées pour cet appareil doivent
être utilisées.
Note: These instructions do NOT apply to the outer glass door
provided in the Outdoor Kit for indoor/outdoor installations of
Montebello See-Through models.
1) Install glass door, as follows:
a) Retrieve the glass door. Visually inspect the gasket on the back of
the frame. Gasket surface must be clean, free of irregularities, and
seated firmly.
b) Position the door in front of the firebox opening, with the top of the
door held away from the fireplace (see Figure 1 on other side).
c) Lower the bottom of the door assembly onto the bottom door track,
engaging and centering it in the base channel, and then gently swing
the door up.
d) Using a #3 Phillips screwdriver, fasten the door frame to the door
latches with the two (2) latch screws. The latches should pull forward
to engage the door frame.
Note: Securely tighten latch screws when reinstalling glass door
assembly.
INNOVATIVE HEARTH PRODUCTS • DRT/DRC6300 DIRECT-VENT GAS FIREPLACES • DOOR REMOVAL/INSTALLATION INSTRUCTIONS
P/N 900347-00 Rev. NC 12/2014
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
IHP.US.com
Innovative Hearth Products reserves the right
to make changes at any time, without notice,
in design, materials, specifications, prices and
also to discontinue colors,styles, and products.
Consult your local distributor for fireplace
code information Printed in U.S.A. © 2014
Innovative Hearth Products, LLC .
P900347-00
2) Install the modesty panel on the top flange of the glass door, as follows:
a) Grasp the modesty panel with both hands (with the open hem facing
down).
b) Engage it with the upper lip of the glass door frame by pushing it
all the way down. Make sure the installed modesty panel is firmly
in place.
3) Install the barrier, as follows:
a) Slide the barrier, flat side toward the fireplace, into the right barrier
bracket with gap below.
b) Reinsert the lower filler piece by sliding the tab behind the barrier.
c) Center the barrier between the left and right barrier brackets and
lower the barrier until the lower filler piece and barrier are flush with
the bottom of the glass door.
fire-parts.com