Inspire Dual Chest/Shoulder Supplement

ASSEMBLY & OPERATION MANUAL
DUAL Chest/Shoulder
RECORD SERIAL NUMBER HERE
www.inspirefitness.com by Health In Motion LLC 1-10-17

CONGRATULATIONS… You’ve just taken the first step to a healthier
and stronger body. This Dual Chest/Shoulder machine by Inspire offers the
key to unlocking your body’s potential. Regular strength training on a
multi-gym has been shown to deliver a host of benefits including: increased
muscle tone, decreased body fat, improved energy levels, a reduction in
stress, and improved cardiac output. Once again, congratulations, you are
on your way to improving your self image, overall health, and quality of life.
BEFORE ASSEMBLING YOUR DUAL CHEST/SHOULDER
IMPORTANT: Read this entire manual before attempting to build or use
this Dual Chest/Shoulder machine. This manual contains step by step
instructions for proper assembly.
Use the parts list included in this manual to verify that all parts are
accounted for before assembly. If any parts are missing, contact the dealer
of this Dual Chest/Shoulder machine for replacement parts or call Inspire at
877-738-1729.
Make sure that adequate room has been cleared before attempting to build
your Dual Chest/Shoulder machine. A rubber mat is recommended for use
under your Dual Chest/Shoulder machine to protect wood flooring or
carpeting from damage during assembly and usage. In a multi-use setting
or commercial setting, it is recommended that the machine be bolted to the
floor through the holes in the base plates.
This Dual Chest/Shoulder machine is intended for indoor use only. Rust can
form on certain parts in a humid environment resulting in impaired function.
Service of your Dual Chest/Shoulder machine should only be preformed by
an authorized Inspire dealer. Service preformed by anyone else can result
in loss of warranty. If you need help finding an authorized dealer, please
contact us directly:
Inspire Fitness
255 Airport Circle
Suite 101
Corona, CA 92880
Ph: 877-738-1729
Fx: 714-738-1728
www.inspirefitness.com

TABLE OF CONTENTS
Section Description……………………………………………………. Page
Important Safety Instructions………………………………………. 1
Tools Required………………………………………………………………… 1
Parts & Hardware List……………………………………………………. 2
Cable Charts…………….……………………………………………………. 3
Assembly Instructions……………………………………………………. 5
Decal Reference……………………………………………………………… 25
Decal Placement……………………………………………………………. 27
Options, Training Tips…………………………………………………… 28
Maintenance Schedule…….……………………………………………… 29
Limited Warranty…………………………………………………………….. 31

Page 1
IMPORTANT SAFETY INSTRUCTIONS
Please read this entire manual and familiarize yourself with all decals and
warnings before using this Dual Chest/Shoulder machine.
• WARNING! It is necessary to inspect this Dual Chest/Shoulder machine
regularly to maintain safety and proper function. Please use the
maintenance schedule included towards the back of this manual.
Immediately replace any and all defective or worn parts. Pay special
attention to moving parts such as the cables and pulleys and connections
to accessories. See General Maintenance section for complete details.
• Use this Dual Chest/Shoulder machine for its intended purpose as
described in this Operation Manual or the Exercise Book. Do not use
attachments not recommended by the manufacturer.
• Make sure bystanders are at least 5 feet away from the Dual
Chest/Shoulder machine while it is in use.
• Keep children off the Dual Chest/Shoulder machine at all times.
• Keep the Dual Chest/Shoulder machine away from walls and clear of any
obstructions.
• Stop immediately if you experience shortness of breath, pain, or dizziness
during your workout. Inspire strongly recommends consulting your
doctor before starting an exercise program.
TOOLS REQUIRED FOR ASSEMBLY
• Metric socket set (including 16mm, 17mm, and 19mm sockets)
• Metric wrenches (16mm, 17mm, and 19mm)
• 4mm, 5mm, and 6mm Allen wrenches (supplied in hardware pack)
• Adjustable wrench
• Philips screwdriver

Page 2
DUAL CHEST/SHOULDER PARTS & HARDWARE LIST
Item Parts Description Qty Qty Rec'd Item Hardware Description Qty Qty Rec'd
1 Main Frame 1 1 M10 x 25 Hex Bolt 18
2 Guide Cable Support 1 2 M10 x 95 Hex Bolt 2
3 Upright 1 1 3 M10 x 75 Hex Bolt 6
4 Upper Arm 1 4 M10 x 95 Hex Bolt 2
5 Lower Arm Mount 1 5 M10 x 90 Hex Bolt 4
6 Base Frame 1 6 M10 x 125 Hex Bolt 2
7 Upper Pulley Mount, Left 1 7 M8 x 20 Hex Bolt 2
8 Upper Pulley Mount, Right 1 8 M10 x 100 Hex Bolt 3
9 Top Weight Stop Assembly 2 9 M10 x 20 Hex Bolt 2
10 Guide Rods 4 10 M10 x 50 Hex Bolt 6
11 Top Weight/Selector Stem 2 11 M8 x 100 Hex Bolt 1
12 Rubber Donut 4 12 M6 x 12 Button Head Bolt 10
13 Upright 2 1 13 M10 x 50 Fully Threaded Hex Bolt 3
14 Floating Pulley Bracket 2 14 M10 x 25 Button Head Bolt 3
15 Lower Arm Mount 1 15 M10 x 70 Hex Bolts 2
16 Seat Frame 1 16 M8 x 12 Button Head Bolt 7
17 Weight Spacer 4
18 Top Weight 2 17 M10 Flat Washer 88
19 Springs 4 18 M8 Flat Washer 11
20 Left Metal Shroud Plate 1 19 M10 Large OD Flat Washer 2
21 Right Metal Shroud Plate 1 20 M6 Flat Washer 10
22 Seat Pad 1
23 Backpad 1 21 M10 Locknut 37
24 Guide Cables 4 22 M8 Locknut 1
25 Upper Metal Shroud 1
26 Lower Metal Shroud 1 22 Cable Adapter 2
27 Fabric Shroud 1 23 "U" Bracket Cable End 4
28 Metal Shroud Placard Left 1 24 Cable Ball 4
29 Metal Shroud Placard Right 1 25 Spring Clip 4
30 Rubber Cup 2 26 Weight Pin 2
31 Rubber Tablet Holder 1 27 4 mm Allen Wrench 1
32 Molded Top Cap 1 28 5 mm Allen Wrench 2
33 Lower Pulley Mount 1 29 6 mm Allen Wrench 1
34 Seat Stem 1
35 Guide Rod Lube 1
36 "D" Handle Assembly, Long 2
37 "D" Handle Assembly 2
38 Touch-up Paint 1
38 3 1/2" Pulley 2
39 4 1/2" Pulley 2

Page 3
1233 mm
5722 mm
1291 mm
Weight Cable p/n GM881-500-002
Cable lengths are in millimeters and for reference only.
Cable lengths could change at any time without notice.
Main Cable p/n GM884-500-001
Guide Cable p/n GM881-500-001
DUAL LINE CHEST/SHOULDER CABLE CHART

Page 4
ASSEMBLY INSTRUCTIONS

Page 5
Step 1: Attach Upright 1 to the Main Frame using: 2 - M10 x 25 Hex Bolts
2 - M10 x 95 Hex Bolts
6 - M10 Flat Washers
2 - M10 Locknuts
Step 2: Attach Guide Cable Support to Main Frame
and Upright 1 using: 4 - M10 x 75 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
NOTE: Finger Tighten Only.
Step 1
Step 2
2 - M10 x25 Hex Bolts
2 - M10 x 95 Hex Bolts
6 - M10 Flat Washers
2 - M10 Locknuts
4 - M10 x 75 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
Upright 1
Main Frame
Guide Cable
Support

Page 6
Step 3: Attach the Base Frame to the Upright 1 using: 2 – M10 x 125 Hex Bolts
4 – M10 Flat Washers
2 – M10 Locknuts
Adjust the height of the adjustment foot in the
back of the machine so that the adjustment foot is
resting on the floor.
NOTE: Finger Tighten Only.
Step 3
2 - M10 x 125 Hex Bolts
4 - M10 Flat Washers
2 - M10 Locknuts
Base Frame
Upright 1
Adjustment Foot

Page 7
Step 4: Attach the Upright 2 to the Base Frame and
Upright 1 using: 4 – M10 x 125 Hex Bolts
8 – M10 Flat Washers
4 – M10 Locknuts
NOTE: Wrench tighten all hardware from Steps 1, 3, and 4 now.
Step 4
4 - M10 x 125 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
Upright 1
Upright 2
Base Frame

Page 8
Step 5: Attach the Lower Arm Mount to the Base Frame and
Upright 2 and the Seat Frame to the Upright 2 using: 2 – M10 x 95 Hex Bolts
1 – M10 x 100 Hex Bolt
2 – M10 x 20 Hex Bolts
8 – M10 Flat Washers
3 – M10 Locknuts
NOTE: Wrench Tighten Now.
Step 5
2 - M10 x 95 Hex Bolts
1 - M10 x 100 Hex Bolts
2 - M10 x 20 Hex Bolts
8 - M10 Flat Washers
3 - M10 Locknuts
Lower Arm Mount
Upright 2
Base Frame
Seat Frame

Page 9
Step 6: Attach the Lower Arm to the Lower Arm Mount using: 4 – M10 x 25 Hex Bolts
8 – M10 Flat Washers
4 – M10 Locknuts
NOTE: Wrench Tighten Now.
Step 6
4 - M10 x 25 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
Lower Arm
Lower Arm Mount

Page 10
Step 6: Attach the Upper Arm to the Upright 2 using: 4 – M10 x 25 Hex Bolts
8 – M10 Flat Washers
4 – M10 Locknuts
NOTE: Wrench Tighten Now.
Step 7
4 - M10 x 25 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
Upright 2
Upper Arm

Page 11
Step 8: Insert two Guide Rods into the holes in the bottom tube of the Main Frame. Carefully tilt the
Guide Rods back away from the machine. Slide one Rubber Donut and Weight Spacer into each
Guide Rod. Slide fifteen Weight Plates onto the Guide Rods. Make sure the recessed area on the
front of the weight plate is facing towards the front of the machine. Slide Top Weight assembly
onto the Guide Rods. Slide the Top Weight Stop Assembly onto the Guide Rods making sure the
rubber pad is facing down. Attach the Upper Pulley Mount, Top Weight Stop Assembly, and Guide
Rods to the Main Frame Using:
1 - M10 x 75 Hex Bolt
Optional: To make room for heavy stack application, 2 - M10 x 90 Hex Bolts
do not add the two weight spacers but 6 - M10 Flat Washers
instead add 50 lbs on each side above the 3 - M10 Locknuts
rubber donuts.1 - M8 x 20 Hex Bolt
1 - M8 Flat Washer
NOTE: Finger Tighten Only.
Step 8
1 - M8 x 20 Hex Bolts
1 - M8 Flat Washer
1 - M10 x75 Hex Bolts
2 - M10 x90 Hex Bolts
6 - M10 Flat Washers
3 - M10 Locknuts
Bottom of weight
plate has three feet
Front of weight plate has recessed
area for the number sticker
Upper Pulley Mount, Left
Rubber Donut
Guide Rods
Weight Spacer
Top Weight
Top Weight
Stop Assembly
Main Frame

Page 12
Step 9: Insert two Guide Rods into the holes in the bottom tube of the Main Frame. Carefully tilt the
Guide Rods back away from the machine. Slide one Rubber Donut and Weight Spacer into each
Guide Rod. Slide fifteen Weight Plates onto the Guide Rods. Make sure the recessed area on the
front of the weight plate is facing towards the front of the machine. Slide Top Weight assembly
onto the Guide Rods. Slide the Top Weight Stop Assembly onto the Guide Rods making sure the
rubber pad is facing down. Attach the Upper Pulley Mount, Top Weight Stop Assembly, and Guide
Rods to the Main Frame Using:
1 - M10 x 75 Hex Bolt
Optional: To make room for heavy stack application, 2 - M10 x 90 Hex Bolts
do not add the two weight spacers but 6 - M10 Flat Washers
instead add 50 lbs on each side above the 3 - M10 Locknuts
rubber donuts.1 - M8 x 20 Hex Bolt
1 - M8 Flat Washer
NOTE: Finger Tighten Only.
Step 9
1 - M8 x 20 Hex Bolts
1 - M8 Flat Washer
1 - M10 x75 Hex Bolts
2 - M10 x90 Hex Bolts
6 - M10 Flat Washers
3 - M10 Locknuts
Front of weight plate has recessed
area for the number sticker
Bottom of weight
plate has three feet
Top Weight
Stop Assembly
Main Frame
Top Weight
Guide Rods
Rubber Donut
Weight Spacer
Upper Pulley Mount, Right

Page 13
Step 10: Attach the Lower Pulley Mount to the Upright 1 using: 4 – M10 x 25 Hex Bolts
8 – M10 Flat Washers
4 – M10 Locknuts
NOTE: Finger Tighten Only.
Step 10
4 - M10 x 25 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
Lower Pulley Mount
Upright 1

Page 14
Step 11: Insert the Hex Bolt end of the Weight Cable into the Top Weight Stack. Take the other end of
the Weight Cable and guide it straight up through the Top Weight Stop and around both of the
pulleys in the Upper Pulley Mount, Left. Attach the Floating Pulley to the cable end as shown.
You may need to unscrew the tiny screws in order for the cable adapter to fit.
Repeat same steps for the right side of the machine with the Upper Pulley Mount, Right.
NOTE: Bolts need to be tightened all the way down to the Top Weight Stack or else
bolts may come loose.
Step 11
Upper Cable Routing
Floating Pulley
Top Weight Stack
Upper Pulley Mount, Left
Upper Pulley Mount, Right
Top Weight Stop
Floating Pulley
(Side View)
Cable Adapter
Cable
Selector Stem
Jam Nut
Thread bolt completely into selector stem
and tighten jam nut
DUAL LINE CHEST/SHOULDER CABLE CHART
Cable lengths are in millimeters and for reference only.
Cable lengths could change at any time without notice.
Guide Cable p/n GM881-500-001
Main Cable p/n GM884-500-001
Weight Cable p/n GM881-500-002
Weight Cable

Page 15
Step 12: Insert the Main Cable through the Swivel Pulley on the Upper Arm and around Pulley 1.
Continue to guide the Main Cable into the Open Pulley Slot #1 and out the back of the machine
towards Pulley 3. Wrap around Pulley 3 and go straight downwards towards Pulley 5 on the
Lower Pulley Mount and then up and around the Floating Pulleys. From the Floating Pulleys, go
through the hole on top of the Lower Pulley Mount and down through Pulley 7. Continue to
route the Main Cable through the Open Pulley Slot #2 inside the Base Frame until you can feel
the Main Cable in the Base Frame. Grab the cable and pull it through the swivel pulley and
install the “U” Bracket Assembly on both ends of the Main Cable.
NOTE: Be sure not to pull the Main Cable too hard before installing the “U” Bracket
Assembly as it may slip through the Swivel Pulley.
Repeat for Main Cable on other side for Pulley 2, Pulley 4, Pulley 6, and Pulley 8.
Step 12
Route Cables
“U” Bracket Assembly
Pulley 6
Base Frame
Lower Pulley
Mount
Upright 1
Pulley 5
Pulley 7
Pulley 8
Pulley 1
Pulley 2
Pulley 4
Pulley 3
Floating
Pulleys
Pulley 7
Pulley 5
Open Pulley Slot #2
Open Pulley Slot #1
Swivel Pulley
DUAL LINE CHEST/SHOULDER CABLE CHART
Cable lengths are in millimeters and for reference only.
Cable lengths could change at any time without notice.
Guide Cable p/n GM881-500-001
Main Cable p/n GM884-500-001
Weight Cable p/n GM881-500-002
Main Cable

Page 16
Step 13: When inserting Pulley 9 and Pulley 11, make sure the
cables are in front of the pulleys and are in the pulley
grooves; not above or below the pulley. Attach the Pulley
to the Base Frame using: 4 – M10 x 50 Hex Bolts
8 – M10 Flat Washers
Repeat for Pulley 10 and Pulley 12 on the right side 4 – M10 Locknuts
of the machine.
NOTE: Wrench Tighten Now.
Step 13
4 - M10 x 50 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
Upright 2
Base Frame
Pulley 9
Pulley 11
Pulley 12
(Right side of machine)
Pulley 10
(Right side of machine)
Pulley 9 & Pulley 10 Cable Guide
Pulley 11 & Pulley 12 Cable Guide